Home › Symptom guides › ABS light on
Warning light

Why is my ABS light on?

The ABS light means the anti-lock part of your brakes has switched itself off because it found a fault. Normal braking is designed to keep working without ABS, but the wheels can lock up in a hard stop, and a website can't check the rest of the brake system for you. What else is on the dash and how the pedal feels decide how urgent it is.

Stop and get help right away if:
  • If the red BRAKE light is on together with the ABS light, don't drive the car until it's checked.
  • If the brake pedal feels soft, sinks toward the floor, or the car takes longer to stop, pull over safely and don't drive on.
  • If you smell burning from a wheel or see smoke from a wheel after driving, stop and let it cool. A brake may be dragging.
Question 1

Along with the ABS light, which of these is true?

The red BRAKE light usually says BRAKE or shows an exclamation mark inside a circle. It is different from the amber ABS light.

Full guide: every possible outcome

Prefer to read it all? Here's every result this guide can reach.

ABS and red brake light together can mean a real brake problemStop — don't drive it

What to do now: Don't drive it. Check the brake fluid level if you can, then have the car towed or call a mobile mechanic.

Why: The red brake light warns about the main braking system, not just the anti-lock part. When both are on, the system that balances braking between front and rear wheels may also be off, or fluid may be low. The rear wheels can lock and the car can spin in a hard stop.

Possible causes: Low brake fluid from a leak or very worn pads; ABS module or wheel speed sensor fault that can also switch off front-to-rear brake balance; Parking brake not fully released.

A shop will usually test: ABS and brake system code scan; Brake fluid leak inspection; Brake pad and hydraulic system check.

A soft or sinking pedal means the brakes themselves need attentionStop — don't drive it

What to do now: Don't drive it. Have the car towed or have a mobile mechanic check the brakes where it is.

Why: With an ABS fault alone, normal braking is designed to keep working. A pedal that feels soft or sinks is different: it can point to air in the lines, a fluid leak or a master cylinder problem, and the brakes can get worse quickly.

Possible causes: Brake fluid leak; Master cylinder problem; Air in the brake lines.

A shop will usually test: Brake system inspection for leaks; Master cylinder test (a shop will usually rule out leaks and air before replacing it); Brake bleed and ABS code scan.

Low battery voltage can set the ABS light. It may clear on its ownSafe to check yourself first

What to do now: Make sure the battery clamps are tight, then turn the car off for a minute and restart it. Many cars turn the light off after a short, gentle drive once they see the wheels moving normally. Until it goes out, anti-lock braking is off, so leave extra stopping distance.

Why: The ABS system checks itself every time you start the car. If the voltage dips during a weak start or a jump, it can log a fault and switch off as a precaution. Once the power is steady, it often passes its self-check again.

Possible causes: Fault logged during a low-voltage start; Loose or corroded battery connection; Weak battery or charging problem.

A shop will usually test: ABS code scan and clear; Battery and charging system test.

A wheel speed sensor or its wire may have been disturbed or damagedGet it checked in the next few days

What to do now: Get the ABS codes read within the next few days. If the light came on right after a repair, go back to the shop that did the work.

Why: Each wheel has a sensor that tells the ABS how fast it is turning. Brake, hub or suspension work can leave a sensor unplugged or a wire stretched, and a hard pothole can crack the sensor or the toothed ring it reads.

Possible causes: Wheel speed sensor unplugged or damaged; Damaged sensor wiring; Damaged or dirty tone ring.

A shop will usually test: ABS code scan to find which wheel; Live wheel speed sensor data on a test drive; Sensor wiring and tone ring inspection.

An on-and-off ABS light often points to a wheel speed sensor or its wiringBook a check when convenient

What to do now: Book an ABS check when convenient, and ask the shop to read the stored codes even if the light is off that day.

Why: When the light comes and goes, the ABS is usually getting a weak or broken signal from one wheel. Rust, road salt and flexing wires are common causes. While the light is on, anti-lock braking is off.

Possible causes: Wheel speed sensor with a weak signal; Wiring chafed or corroded near a wheel; Rust buildup under the sensor.

A shop will usually test: ABS code scan, including stored codes; Wheel speed sensor data on a test drive; Wiring and connector inspection at each wheel.

The anti-lock system has switched off and needs a code scanGet it checked in the next few days

What to do now: Get the ABS codes read within the next few days. Until then, leave extra following distance and brake earlier.

Why: A steady ABS light means the system found a fault and turned anti-lock braking off. Normal braking is designed to keep working without it, but the wheels can lock and skid in a hard stop. An ABS code scan tells the shop which wheel or circuit to test first.

Possible causes: Wheel speed sensor or its wiring; Low brake fluid; ABS module, pump or fuse problem.

A shop will usually test: ABS code scan (a basic engine code reader may not see ABS codes); Wheel speed sensor data; ABS fuse, pump and module check.

Related guides

Sources and references: Nissan · Mazda · National Highway Traffic Safety Administration (NHTSA)

This guide helps you understand what may be going on and how urgent it is. It doesn't replace an in-person inspection.