Why is my airbag light on?
The airbag light (often marked SRS or showing a seated person with a ball in front) should come on for a few seconds at startup and then go out. If it stays on or flashes, the system has found a fault and the airbags may not work in a crash. The car may drive the same, but you may not have full crash protection, so the main question is how soon to get it checked.
- Don't unplug, probe or remove airbag parts or the yellow connectors under the seats yourself. An airbag can deploy and cause serious injury.
- Until it's fixed, seat children in the back seat in the right car seat or booster, as you always should.
- If an airbag has deployed, don't drive the car. Deployed airbags can't protect you again, and there's likely other damage.
What exactly are you seeing?
SRS stands for Supplemental Restraint System, which means the airbags and seat belt tensioners. The separate PASSENGER AIRBAG OFF light, usually near the center of the dash or by the mirror, is a different indicator.
Full guide: every possible outcome
Prefer to read it all? Here's every result this guide can reach.
The passenger airbag indicator is often normal. Check who's in the seatSafe to check yourself first
What to do now: Check whether the light matches who's sitting there. It should show OFF when the seat is empty or holds a small child or child seat, and ON (or go out) when an adult sits normally.
Why: Many cars have a weight or occupant sensor in the passenger seat that turns that airbag off for an empty seat or a small passenger. The OFF light is usually telling you what it decided, which isn't necessarily a fault.
Possible causes: Normal operation; Passenger sitting out of position; Faulty passenger seat sensor.
A shop will usually test: Airbag system code scan; Occupant sensor test and recalibration.
After an airbag deploys, the system must be repaired before drivingStop — don't drive it
What to do now: Don't drive it. Have it towed to a collision repair shop or dealer.
Why: A deployed airbag can't protect you again, and the crash sensors and control module usually need replacing too. The crash itself may also have damaged steering, suspension, or lights.
Possible causes: Deployed airbags and seat belt tensioners; Crash data stored in the airbag module.
A shop will usually test: Airbag system code scan; Replacement of deployed airbags, tensioners and crash sensors; Airbag module replacement or reset; Collision damage inspection.
A crash sensor or its wiring may have been damaged in the bumpGet it checked in the next few days
What to do now: Have the airbag system scanned within the next few days, ideally by the shop repairing the collision damage.
Why: Crash sensors sit near the front bumper and in the doors or pillars. Even a minor impact can damage a sensor or its wiring, and the system then switches itself off and turns the light on.
Possible causes: Damaged front or side crash sensor; Damaged or disconnected wiring; Stored crash event in the airbag module.
A shop will usually test: Airbag system code scan; Crash sensor and wiring inspection; Airbag module check.
The steering wheel clockspring is a likely place to startGet it checked in the next few days
What to do now: Have the airbag system checked within the next few days. Until then, your driver's airbag may not work, and the horn may not either.
Why: The clockspring is a coiled ribbon cable behind the steering wheel. It keeps the driver's airbag, horn and wheel buttons connected while you turn the wheel. When it wears or breaks, all of these can stop working at once.
Possible causes: Worn or broken clockspring; Clockspring damaged during steering work; Driver airbag connector fault.
A shop will usually test: Airbag system code scan; Clockspring resistance test; Steering wheel circuit check.
A connector under a front seat may have been disturbedGet it checked in the next few days
What to do now: Remove any loose items from under the front seats, then have the airbag codes read and the connector checked within a few days. Don't unplug or reseat the connector yourself.
Why: Side airbags and seat belt tensioners are wired through connectors under the front seats. Sliding the seat, items jammed underneath, or seat removal can loosen a connector or strain a wire, and the system turns the light on.
Possible causes: Loose seat airbag or tensioner connector; Worn wiring under the seat; Faulty seat sensor.
A shop will usually test: Airbag system code scan; Under-seat connector and wiring inspection; Fault code clearing after repair.
Low battery voltage can leave a stored airbag faultSafe to check yourself first
What to do now: Turn the car off for a minute, then restart it and watch whether the light goes out after a few seconds.
Why: The airbag system checks itself at every start. A weak battery or a jump start can make that check fail and log a fault. On some cars it clears itself, on others it stays until a technician clears it.
Possible causes: Fault logged during a low-voltage start; Loose battery connection; A separate airbag fault that showed up at the same time.
A shop will usually test: Airbag system code scan and clear; Battery and charging system test.
A seat belt buckle or tensioner fault may be the causeGet it checked in the next few days
What to do now: Have the airbag and seat belt system checked within a few days. Keep wearing the belt and make sure it latches firmly every time.
Why: Seat belt buckles have switches that tell the airbag system whether you're belted, and the belts have tensioners that tighten in a crash. A faulty buckle switch or tensioner circuit turns the airbag light on.
Possible causes: Buckle switch problem; Tensioner circuit fault; Debris in the buckle.
A shop will usually test: Airbag system code scan; Buckle switch test; Seat belt tensioner circuit check.
The airbag system has a fault and may not deploy in a crashGet it checked in the next few days
What to do now: Have the airbag system scanned within the next few days. Also check for open airbag recalls using your VIN.
Why: When the airbag light stays on, the system may have disabled some or all airbags because it can't confirm they'll work properly. The car may drive the same, but you may not have full crash protection. An airbag scan tool reads the stored codes, which tell the shop which circuit to test first.
Possible causes: Steering wheel clockspring; Seat connector, buckle or occupant sensor; Crash sensor or airbag module fault.
A shop will usually test: Airbag (SRS) code scan (a basic engine code reader can't read these); Clockspring and seat connector checks; Crash sensor and module check.
Related guides
Sources and references: Kia owner's manual · National Highway Traffic Safety Administration (NHTSA)