Why are my brakes dragging or one wheel hot?
A dragging brake stays partly on when you're not pressing the pedal. You may notice a hot wheel, a burning smell, the car pulling to one side, or a car that feels like it's working harder than it should. Answer a few questions to find which brake is sticking and how soon to deal with it.
- If you see smoke from a wheel or smell strong burning, pull over safely and let the brakes cool before going near them.
- If the brake pedal goes soft or sinks, or the car is much harder to stop, stop driving and have it towed.
- If the red brake warning light stays on with the parking brake fully released, have the brakes checked before driving.
- Never touch a brake rotor or wheel to test it. It can be hot enough to burn you.
What are you noticing?
A caliper is the clamp at each wheel that squeezes the brake pads against the disc (rotor).
Full guide: every possible outcome
Prefer to read it all? Here's every result this guide can reach.
A brake may be overheating, possibly from sticking onStop — don't drive it
What to do now: Pull over somewhere safe, turn off the engine and let the brakes cool for at least 30 minutes. Then have the car towed or call a mobile mechanic.
Why: Smoke or a burning smell usually means a brake is getting far hotter than normal. That often happens when it doesn't release, so it rubs constantly. Overheated brakes can fade and stop working well, and in bad cases can set grease or the tire alight.
Possible causes: Sticking caliper; Parking brake left on or not releasing; Heavy braking on a long descent.
A shop will usually test: Caliper and slide pin inspection; Brake hose inspection; Pad and rotor heat damage check.
A problem in the brake hydraulics or booster may be holding all the brakes onStop — don't drive it
What to do now: Don't drive it. Have the car towed or call a mobile mechanic.
Why: When every wheel drags at once, the cause is often in the parts shared by all four brakes: the master cylinder, the brake booster, or the fluid itself. Brakes that won't release can overheat quickly and then fade when you need them.
Possible causes: Master cylinder not releasing pressure; Brake booster or pedal not returning; Contaminated or wrong brake fluid.
A shop will usually test: Master cylinder release test; Brake booster and pedal return check; Brake fluid inspection.
A sticking brake caliper is a likely causeGet it checked in the next few days
What to do now: Have the brakes checked within a few days. Drive only short, gentle trips until then.
Why: Calipers slide on pins and use a piston that can corrode or stick. When one doesn't release, its pads keep rubbing. That wheel gets hot, the car pulls toward it, and the pads and rotor wear out fast. A shop will usually check the slide pins, piston and hose before deciding which part needs replacing.
Possible causes: Seized or sticking caliper slide pins; Sticking caliper piston; Collapsed brake hose acting like a one-way valve.
A shop will usually test: Raise the car and spin each wheel by hand; Caliper, slide pin and piston inspection; Brake hose inspection; Pad and rotor measurement.
The parking brake may not be fully releasingGet it checked in the next few days
What to do now: Make sure the lever or pedal is fully released, then have the rear brakes checked within a few days. Drive only short, gentle trips until then.
Why: Parking brake cables can rust or freeze, and the springs or parts inside rear brakes can stick. When they don't fully release, the rear brakes keep rubbing, overheat and wear quickly.
Possible causes: Rusted or frozen parking brake cable; Rear brake parts sticking or out of adjustment; Parking brake switch out of adjustment.
A shop will usually test: Parking brake cable inspection; Rear brake inspection and adjustment; Parking brake switch check.
The electronic parking brake may not be releasingGet it checked in the next few days
What to do now: Check the owner's manual for the release steps, which usually involve the brake pedal, the button and the engine running. If it won't release, have the car towed or call a mobile mechanic rather than forcing it.
Why: An electronic parking brake uses small motors at the rear calipers. A weak battery, a failed motor or a system fault can stop it from releasing, and driving against it can damage the brakes quickly.
Possible causes: Parking brake motor or caliper fault; Low battery voltage; System needs a reset after brake work.
A shop will usually test: Parking brake module code scan; Motor and caliper test; Battery and charging test.
The red brake light with the parking brake off can mean low brake fluidStop — don't drive it
What to do now: Don't drive until the brakes are checked. With the engine off, look at the brake fluid level in the reservoir, then have the car towed or call a mobile mechanic.
Why: The red brake light covers the parking brake and the brake fluid level. If it stays on with the parking brake released, fluid may be low from a leak or very worn pads, which can affect stopping.
Possible causes: Low brake fluid from a leak; Very worn brake pads; Parking brake switch stuck on.
A shop will usually test: Brake fluid leak inspection; Pad thickness check; Brake warning switch test.
Something from the recent brake work may be bindingGet it checked in the next few days
What to do now: Take it back to the shop that did the work within a few days, and tell them which wheel is hot or noisy. Drive only short, gentle trips until then.
Why: New pads that fit too tightly, slide pins that weren't cleaned and lubricated, or a parking brake that needs adjusting can all keep a brake from releasing fully. The shop that did the work will want to know, and it's often a straightforward recheck, but it shouldn't wait.
Possible causes: Pads binding in the caliper bracket; Slide pins dry or caliper not seated; Rear brakes or parking brake over-adjusted.
A shop will usually test: Recheck pad fit and slide pins; Parking brake adjustment check; Spin each wheel by hand on a lift.
No wheel stands out, so something besides a single brake may be holding the car backBook a check when convenient
What to do now: Check the tire pressures, then book a check for the wheel bearings and drivetrain when convenient.
Why: If no wheel is hotter than the others, a single sticking brake is less likely, but the hand test is rough and can't rule it out. Low tires, a worn wheel bearing, or an engine or transmission problem can also make a car feel sluggish or coast poorly. A shop can spin each wheel on a lift to check.
Possible causes: Low tire pressure; Worn wheel bearing; Engine or transmission not delivering full power.
A shop will usually test: Spin each wheel by hand on a lift; Wheel bearing check; Code scan and road test.
Have the brakes checked to find which wheel is draggingGet it checked in the next few days
What to do now: Make sure the parking brake is fully released, then have the brakes inspected within a few days. Drive only short, gentle trips until then.
Why: A shop can lift the car and spin each wheel by hand to find one that doesn't turn freely. That quickly shows whether a caliper, the parking brake or something else is causing the drag.
Possible causes: Sticking caliper; Parking brake not releasing; Something other than the brakes.
A shop will usually test: Spin each wheel by hand on a lift; Brake inspection; Parking brake check.
Related guides
Sources and references: NAPA Know How · PR Newswire