Home › Symptom guides › Car shakes when accelerating
Shaking

Why does my car shake when I accelerate?

A shake that shows up when you press the gas usually comes from the engine, the parts that carry power to the wheels, or the tires. When it happens, and whether a warning light is on, helps separate a simple balance issue from a problem that can do real damage. Answer the questions below to narrow it down.

Stop and get help right away if:
  • If the check engine light is flashing, ease off the gas and pull over. A severe misfire can overheat and ruin the catalytic converter.
  • If the shaking suddenly becomes violent or you hear a thumping that wasn't there before, slow down and pull over safely right away.
  • If you smell fuel or see smoke, stop the car, turn it off and step away.
Question 1

Which of these fits best?

A "misfire" is when one cylinder of the engine doesn't fire properly. It feels like a stumble, jerk or uneven shake, often with a loss of power.

Full guide: every possible outcome

Prefer to read it all? Here's every result this guide can reach.

A flashing check engine light usually means a severe misfireStop — don't drive it

What to do now: Ease off the gas, pull over when it's safe and turn the engine off. Have it towed or call a mobile mechanic.

Why: A flashing light usually means the misfire is bad enough to cause damage now. Unburned fuel goes into the exhaust and can overheat the catalytic converter, which can be costly to replace and is a fire risk in extreme cases.

Possible causes: Faulty ignition coil or spark plug; Fuel injector problem; Internal engine problem.

A shop will usually test: Code scan and misfire counter data; Ignition coil and spark plug inspection; Fuel injector test; Compression test if needed.

The engine may be misfiring under loadGet it checked in the next few days

What to do now: Get the code read and the engine checked within the next few days. Until then, keep trips short, drive gently and avoid hard acceleration and towing a trailer.

Why: A steady check engine light with a rough, weak feeling under acceleration often means one cylinder isn't firing properly when the engine is working hardest. Worn spark plugs and failing ignition coils are common reasons, but the code and a few tests are needed to know which part is at fault.

Possible causes: Worn spark plugs or a failing ignition coil; Vacuum or intake air leak; Dirty or failing fuel injector or low fuel pressure.

A shop will usually test: Code scan and misfire data; Spark plug and coil inspection; Smoke test for intake leaks; Fuel pressure test.

Sudden, violent shaking can mean a tire or wheel is failingStop — don't drive it

What to do now: Slow down, pull over somewhere safe and stop. Walk around the car and look at each tire. Call roadside assistance if anything looks wrong.

Why: A shake that appears suddenly and hard is different from one that grew over weeks. It often means a tire's internal belts have separated, a wheel is loose, or a drive part has broken. Any of these can lead to losing control.

Possible causes: Tire tread separation or damaged tire; Loose wheel; Broken CV joint, driveshaft joint or engine mount.

A shop will usually test: Tire and wheel inspection on a lift; Lug nut and wheel stud check; Drive axle and mount inspection.

A light shudder at moderate speeds is often linked to the transmission's torque converterBook a check when convenient

What to do now: Book a transmission check and ask the shop to look for a torque converter shudder and the condition of the transmission fluid.

Why: In an automatic, the torque converter has a clutch that locks up at cruising speeds to save fuel. When that clutch or the fluid is worn, it can grab unevenly, which feels like rolling over rumble strips under light gas. A misfire can feel very similar, so a shop will usually check for engine codes as well.

Possible causes: Torque converter clutch shudder; Old or degraded transmission fluid; Mild engine misfire.

A shop will usually test: Code scan, including transmission codes; Transmission fluid condition check; Road test watching torque converter lockup data.

Worn engine or transmission mounts are a possible causeBook a check when convenient

What to do now: Book an inspection of the engine and transmission mounts.

Why: Mounts are rubber blocks that hold the engine and transmission in place and soak up vibration. When they crack or collapse, the engine rocks when you put power on or let off, and you feel it as a jolt or shake through the car. A shop will usually inspect the mounts and the drive axles together, because a worn axle joint can feel similar.

Possible causes: Worn or broken engine mount; Worn transmission mount; Worn inner CV joint.

A shop will usually test: Visual mount inspection for cracks and separation; Engine torque test watching mount movement; Drive axle inspection.

A worn CV axle is a likely causeGet it checked in the next few days

What to do now: Have the front axles inspected within the next few days. Drive gently and avoid hard acceleration until then.

Why: On front-wheel-drive cars, the CV axles carry power to the wheels through flexible joints. When the inner joint wears, it can wobble under load, so the shake grows as you accelerate and fades when you coast. A torn rubber boot lets grease out and dirt in, which speeds this up. A shop will usually check the axles for play and the mounts before deciding which part is at fault.

Possible causes: Worn inner CV joint; Torn CV boot; Worn engine mount.

A shop will usually test: CV axle and boot inspection on a lift; Check for play in the inner and outer joints; Mount inspection.

A worn driveshaft joint is a possible causeGet it checked in the next few days

What to do now: Have the driveshaft and its joints inspected within the next few days. Drive gently until then.

Why: The driveshaft carries power from the transmission to the rear axle through small universal joints. When a joint wears or the shaft goes out of balance, it shakes more when it's under load and often clunks when you shift into gear.

Possible causes: Worn universal joint (U-joint); Worn driveshaft center support bearing; Driveshaft out of balance or bent.

A shop will usually test: U-joint and center bearing inspection for play; Driveshaft balance and angle check; Differential and mount inspection.

This points to a tire or wheel issue more than an acceleration problemBook a check when convenient

What to do now: Have the tires balanced and inspected at a tire shop.

Why: If the shake depends on speed and not on the gas pedal, it's most likely coming from something that spins with the wheels. An out-of-balance tire, a bent wheel or a damaged tire is the usual reason, though worn wheel bearings or suspension parts can feel similar.

Possible causes: Tire out of balance; Bent wheel; Damaged or out-of-round tire.

A shop will usually test: Wheel balance; Wheel runout (bend) check; Tire inspection.

Have a shop road-test it to find where the shake comes fromBook a check when convenient

What to do now: Book a check and tell the shop when the shake happens: the speed, how hard you're pressing the gas, and whether it fades when you coast.

Why: Shaking under acceleration can come from the engine, the axles, the mounts or the tires. A short road test with a technician usually narrows it down quickly.

Possible causes: Worn CV axle or driveshaft joint; Engine misfire; Worn engine or transmission mounts; Tire or wheel balance.

A shop will usually test: Road test; Code scan; Axle, mount and tire inspection.

Related guides

Sources and references: National Highway Traffic Safety Administration (NHTSA)

This guide helps you understand what may be going on and how urgent it is. It doesn't replace an in-person inspection.