Home › Symptom guides › Check engine light flashing
Warning light

Why is my check engine light flashing?

A flashing check engine light is the engine computer's most urgent warning. It usually means the engine is misfiring badly enough to damage the catalytic converter, and in the worst cases overheat the exhaust. Answer a few questions to see what's likely going on and what to do right now.

Stop and get help right away if:
  • If the light is flashing and the engine is shaking, pull over as soon as it's safe and turn the engine off.
  • If you smell raw fuel or burning, or see smoke from under the car or hood, turn the engine off and get everyone away from the car.
  • If the temperature gauge reaches red, pull over and turn the engine off. Don't open the radiator cap while it's hot.
Question 1

Is the light flashing right now with the engine running?

Flashing means blinking on and off about once a second. A light that stays lit without blinking is a steady check engine light, which is usually less urgent.

Full guide: every possible outcome

Prefer to read it all? Here's every result this guide can reach.

The engine may be misfiring badly. Stop driving it nowStop — don't drive it

What to do now: Pull over where it's safe, turn off the engine, and have the car towed or call a mobile mechanic.

Why: A flashing light with shaking usually means one or more cylinders aren't firing. Unburned fuel goes into the exhaust and burns in the catalytic converter, which can overheat it within minutes. Every mile you drive raises the repair bill and the fire risk. A shop will check misfire data by cylinder and test the coil, plug and injector before replacing anything.

Possible causes: Failed ignition coil; Worn or fouled spark plug; Fuel injector stuck or not firing; Mechanical engine problem.

A shop will usually test: Code scan and misfire counts by cylinder; Ignition coil and spark plug test; Fuel injector test; Compression or leak-down test.

A misfire may be happening even if you can't feel it. Don't keep drivingStop — don't drive it

What to do now: Pull over where it's safe and turn off the engine. Have the car towed or call a mobile mechanic.

Why: The computer flashes the light when it counts enough misfires to risk overheating the catalytic converter. A misfire on one cylinder isn't always easy to feel, especially at steady speed, but the damage to the converter still happens.

Possible causes: Failing ignition coil or spark plug; Fuel injector problem; Vacuum leak.

A shop will usually test: Code scan and misfire counts by cylinder; Ignition coil and spark plug test; Smoke test for vacuum leaks.

Fuel or exhaust heat may be creating a fire riskStop — don't drive it

What to do now: Pull over, turn off the engine, get everyone out and away from the car, and call for help.

Why: A severe misfire sends raw fuel into a very hot exhaust. That can make the catalytic converter glow red-hot and ignite anything nearby, like dry grass under the car. A fuel smell can also mean a leak near hot engine parts.

Possible causes: Overheated catalytic converter from misfire; Leaking fuel injector or fuel line; Oil or fluid on hot exhaust.

A shop will usually test: Fuel leak inspection; Catalytic converter and exhaust inspection; Code scan and misfire tests.

Coolant may be getting into the engineStop — don't drive it

What to do now: Pull over, turn off the engine, and have the car towed. Don't open the radiator cap while the engine is hot.

Why: A misfire together with overheating or coolant loss can mean coolant is leaking into a cylinder, for example through a failed head gasket. Coolant doesn't burn, so that cylinder misfires. Driving on it can warp the engine and cause major damage. A shop will pressure-test the cooling system and test for combustion gases before deciding what has failed.

Possible causes: Failed head gasket; Cracked cylinder head or intake gasket leak; Overheating causing misfires.

A shop will usually test: Cooling system pressure test; Combustion gas (block) test; Compression or leak-down test.

Bad or wrong fuel, or fuel starvation, may be causing the misfireStop — don't drive it

What to do now: Pull over where it's safe, turn off the engine, and have the car towed. Tell the shop where and when you filled up.

Why: Water in the fuel, the wrong fuel, or a fuel pump struggling on an almost-empty tank can all leave the engine without the right mixture. That causes misfires across several cylinders at once, which flashes the light.

Possible causes: Contaminated or wrong fuel; Fuel starvation from a very low tank or weak pump; Clogged fuel filter or injectors.

A shop will usually test: Fuel sample check; Fuel pressure test; Code scan and misfire data.

Possibly a weak ignition coil or worn spark plugsGet it checked in the next few days

What to do now: If the light flashes again or the engine shakes hard, pull over when it's safe and turn the engine off. Otherwise: Get it checked within a few days. Until then, drive gently, avoid hard acceleration and steep hills, and don't tow or haul anything.

Why: Spark plugs and coils need more energy to fire when the engine is working hard. A weak coil or worn plug can cope at light throttle but misfire under load. A shop will usually swap or test the coil and inspect the plugs to confirm which one is at fault, and the repair is often fairly simple if it's done before the catalytic converter is damaged.

Possible causes: Weak ignition coil; Worn spark plugs; Fuel delivery weakness.

A shop will usually test: Code scan and misfire counts by cylinder; Ignition coil test or swap test; Spark plug inspection.

A cold-start misfire may be a coil, plug or injector starting to failGet it checked in the next few days

What to do now: If the light flashes again or the engine shakes hard, pull over when it's safe and turn the engine off. Otherwise: Get it checked within a few days. On cold mornings, let it idle until it runs smoothly before driving off.

Why: A cold engine is harder to fire, so a weak coil, worn plug or leaky injector often shows up there first. A misfire that only happens cold and then clears up is an early warning that often gets worse. The stored code and a few tests will show which part is involved.

Possible causes: Weak ignition coil or worn spark plug; Leaking or sticking fuel injector; Small coolant leak into a cylinder.

A shop will usually test: Code scan and misfire data; Ignition and injector tests; Cooling system pressure test if coolant is dropping.

The misfire may come back. Get the code read soonGet it checked in the next few days

What to do now: If the light flashes again or the engine shakes hard, pull over when it's safe and turn the engine off. Otherwise: Have the stored code read within a few days. Drive gently and keep trips short until then.

Why: The computer stores a misfire code even after the light stops flashing. A one-time flash often comes from a part that's starting to fail, and it's usually much cheaper to fix now than after it damages the catalytic converter.

Possible causes: Ignition coil or spark plug starting to fail; One-off fuel or moisture problem; Loose connector on a coil or injector.

A shop will usually test: Code scan including stored misfire data; Ignition coil and spark plug inspection; Connector check.

Watch the light closely. If it's flashing, stop drivingGet it checked in the next few days

What to do now: If the light is blinking, pull over when it's safe and turn the engine off. If it's steady and the car drives normally, have the code read within a few days.

Why: A flashing light and a steady light mean very different things. Flashing means a misfire that can damage the catalytic converter right now. Steady means a fault worth checking, which is usually not an emergency unless the car runs poorly or other warning lights come on.

Possible causes: Misfire; Emissions or sensor fault.

A shop will usually test: Code scan; Misfire data review.

Related guides

Sources and references: AAA · Edmunds

This guide helps you understand what may be going on and how urgent it is. It doesn't replace an in-person inspection.