Home › Symptom guides › Check engine light on
Warning light

Why is my check engine light on?

A steady check engine light means the engine computer has found a fault and stored a code. It covers hundreds of problems, from a loose gas cap to a failing sensor. Many are not emergencies, but the light alone can't tell you which. How the car is driving gives you a sense of how urgent it is, and a code scan tells the shop where to start testing.

Stop and get help right away if:
  • If the check engine light starts flashing, or the engine shakes or stumbles hard, pull over and turn the engine off. A severe misfire can overheat the exhaust.
  • If the temperature gauge reaches red, or the red oil light comes on, pull over and turn the engine off.
  • If you smell raw fuel or see smoke from under the hood, pull over, turn the engine off and step away from the car.
Question 1

How is the car driving right now?

Full guide: every possible outcome

Prefer to read it all? Here's every result this guide can reach.

The engine may be misfiring. Stop driving it until it's checkedStop — don't drive it

What to do now: Pull over where it's safe, turn off the engine, and have the car towed or call a mobile mechanic.

Why: Shaking or stumbling with the check engine light on usually means one or more cylinders aren't firing. Unburned fuel then goes into the exhaust, where it can overheat and ruin the catalytic converter, and in bad cases start a fire. Driving on it can turn a small repair into a big one. The code and misfire data tell the shop which cylinder and parts to test.

Possible causes: Failed ignition coil or worn spark plug; Fuel injector problem; Vacuum leak or mechanical engine problem.

A shop will usually test: Code scan and misfire data; Spark plug and ignition coil check; Fuel injector test; Compression test if needed.

A red warning light comes first. Stop and deal with thatStop — don't drive it

What to do now: Pull over safely, turn off the engine, and don't restart it. Have the car towed or call a mobile mechanic.

Why: Red warning lights mean something that can damage the engine or leave you stranded within minutes: overheating, low oil pressure or a charging failure. The check engine light is often just reporting the same problem. The red light sets the urgency.

Possible causes: Engine overheating; Low oil pressure; Charging system failure.

A shop will usually test: Code scan; Cooling system pressure test; Oil pressure test; Charging system test.

The car may have gone into a protective low-power modeGet it checked in the next few days

What to do now: Keep driving to a minimum. A tow is the safest option. If you must move it, keep it to a short, gentle trip to a shop on low-speed roads and avoid highways.

Why: When the computer sees a fault that could damage the engine or transmission, it often limits power or holds a single gear to protect them. The car can still move, but it can be dangerously slow merging or on hills. A code scan points to the cause.

Possible causes: Throttle or accelerator pedal sensor fault; Transmission fault; Turbocharger or boost problem.

A shop will usually test: Code scan and live data; Throttle and pedal sensor tests; Transmission scan and fluid check.

A fuel leak is possible. Don't drive until it's foundStop — don't drive it

What to do now: Turn the engine off, look under the car for wet spots or dripping fuel, and have the car towed to a shop.

Why: The check engine light often comes on for fuel vapor leaks. A faint smell from a loose cap is minor, but a strong raw fuel smell can mean liquid fuel is leaking near hot engine or exhaust parts, which is a fire risk.

Possible causes: Leaking fuel line, injector or fuel rail; Leaking fuel tank, filler neck or vapor hose; Loose or damaged gas cap.

A shop will usually test: Fuel leak inspection; Evaporative system smoke test; Code scan.

A loose or worn gas cap is a common causeSafe to check yourself first

What to do now: Take the gas cap off, check the rubber seal for cracks, and put it back on until it clicks. Then drive normally for a few days.

Why: The fuel system is sealed to keep gasoline vapor in. If the cap isn't tight after a fill-up, the computer can detect a small leak and turn on the light. The light doesn't go out right away after you fix it. It usually needs several days of driving to recheck. If it stays on, the code will show whether the cap or another part of the system is the cause.

Possible causes: Gas cap not tightened; Worn or cracked gas cap seal; Other fuel vapor system leak.

A shop will usually test: Code scan; Gas cap pressure test; Evaporative system smoke test.

Possibly an oxygen sensor or catalytic converter problemBook a check when convenient

What to do now: Have the code read and book a check within the next couple of weeks.

Why: Oxygen sensors measure the exhaust so the computer can adjust the fuel mix. When one fails, mileage often drops. A worn catalytic converter can't clean the exhaust properly, which can cause a sulfur smell. A shop will usually test the sensors and check for misfires or fuel mixture problems before replacing a converter, since those can damage a new one too.

Possible causes: Failing oxygen sensor; Worn catalytic converter; Engine running too rich or lean.

A shop will usually test: Code scan and live sensor data; Oxygen sensor test; Catalytic converter efficiency and back-pressure test.

A small misfire or vacuum leak may be the causeGet it checked in the next few days

What to do now: Have the code read and get it checked within a few days. Keep trips short and gentle until then.

Why: A rough idle with the check engine light on often means a cylinder is misfiring now and then, or extra air is getting in through a cracked hose. Caught early, these are often simple repairs once a shop confirms the cause. Left alone, a misfire can damage the catalytic converter.

Possible causes: Worn spark plug or weak ignition coil; Vacuum leak; Dirty throttle body or fuel injector.

A shop will usually test: Code scan and misfire data; Smoke test for vacuum leaks; Spark plug and coil inspection.

Possibly a sensor or wiring fault that comes and goesBook a check when convenient

What to do now: Have the code read while the light is on, or ask a shop to read stored codes, and book a check when convenient.

Why: A light that turns itself off often means the fault cleared for now, but the code stays stored. Damp or cold weather can bring out marginal sensors, connectors and small vapor leaks. The stored code shows the shop where to start testing.

Possible causes: Marginal sensor; Corroded connector or chafed wire; Small fuel vapor leak.

A shop will usually test: Code scan including stored and pending codes; Wiring and connector inspection; Evaporative system test if needed.

Get the code read. That's the fastest way to know what it isBook a check when convenient

What to do now: Have the trouble code read within the next week or so. Many auto parts stores do it free, or a shop can do it.

Why: A steady light with a car that drives normally is usually not an emergency, but it's not something to ignore either. The code tells the shop which system to test. Waiting months can let a small fault damage something more expensive, and a second problem may hide behind the light that's already on.

Possible causes: Fuel vapor (evaporative) system leak; Oxygen or airflow sensor fault; Early misfire or ignition problem.

A shop will usually test: Code scan and freeze frame data; Tests for the system the code points to.

Related guides

Sources and references: AAA · Edmunds

This guide helps you understand what may be going on and how urgent it is. It doesn't replace an in-person inspection.