Why does my car click when I turn?
A rhythmic clicking when you turn, especially in parking lots, is a common sign of a worn CV joint on a front axle. A single pop or click when you turn the wheel often points somewhere else, like a strut mount. Answer the questions below to narrow it down and see how urgent it is.
- If the steering suddenly feels loose or a wheel looks tilted, stop driving and get help.
- If you hear a loud bang and the car won't move even though the engine revs, the axle may have broken. Don't keep trying to drive.
- Never crawl under a car that's held up only by a jack.
Along with the clicking, is any of this happening?
Pick the most serious one that fits.
Full guide: every possible outcome
Prefer to read it all? Here's every result this guide can reach.
A CV joint or axle may be close to breakingStop — don't drive it
What to do now: Park it and don't drive any further. Have it towed or have a mobile mechanic come to you.
Why: A CV joint that has gone from clicking to clunking or banging may be badly worn. When it fails, the wheel stops getting power and the car can stop moving, sometimes in traffic. In rare cases it can damage nearby parts. A shop will check the axles for play and look at the mounts, which can also clunk.
Possible causes: Badly worn outer CV joint; Worn inner CV joint; Worn engine or transmission mount.
A shop will usually test: CV axle and joint inspection for play; Engine and transmission mount check.
A steering or suspension joint may be wornStop — don't drive it
What to do now: Have the steering and suspension inspected before the car is driven further. A tow or a mobile mechanic is the safest way to get it checked.
Why: Clicking or popping plus loose steering or clunks over bumps can point to worn parts that hold the wheel in place, like ball joints, tie rod ends or sway bar links. These usually wear gradually, but a ball joint or tie rod that separates can make you lose control, and the site can't tell how worn yours are. A shop will check each joint for play to find which one.
Possible causes: Worn ball joint; Worn tie rod end; Worn sway bar link or bushing.
A shop will usually test: Ball joint and tie rod play check; Sway bar link and bushing inspection; Alignment check after repair.
A worn inner CV joint or axle may be the causeGet it checked in the next few days
What to do now: Have the axles checked within a few days. Accelerate gently until then.
Why: The inner CV joint lets the axle change length as the suspension moves. When it wears, it often causes a shudder when accelerating, sometimes with clicking in turns. It tends to get worse over time. A shop will usually check the axles and mounts together, because a worn mount can feel similar.
Possible causes: Worn inner CV joint; Bent or damaged axle; Worn engine or transmission mount.
A shop will usually test: CV axle inspection and test drive; Engine and transmission mount check; Tire balance check.
A torn CV boot may have let grease out and dirt inGet it checked in the next few days
What to do now: Book an inspection within the next week or so. Avoid sharp turns at speed until it's checked.
Why: The CV boot keeps grease in and dirt and water out of the joint. Once it tears, the joint can run dry and wear quickly. Clicking in turns suggests wear has already started, and it tends to get louder until the joint fails. A shop will check the joint for play to see whether the boot or the axle needs attention.
Possible causes: Torn outer CV boot; Torn inner CV boot.
A shop will usually test: CV boot and joint inspection; Axle play check.
A worn outer CV joint on a front axle is a likely causeBook a check when convenient
What to do now: Book an axle inspection in the next couple of weeks. Avoid hard acceleration in tight turns until then.
Why: Front-wheel-drive and many all-wheel-drive cars have CV joints that let the front wheels steer and get power at the same time. When the outer joint wears, it often clicks in a steady rhythm during tight turns. It usually gets worse gradually, but once it starts clunking it can fail without much more warning.
Possible causes: Worn outer CV joint; Torn CV boot you can't see; Worn strut mount or suspension part.
A shop will usually test: CV joint and boot inspection on a lift; Axle play check; Road test in tight turns.
On a rear-wheel-drive car, a front steering or suspension part is more likelyBook a check when convenient
What to do now: Book a front suspension and steering check in the next couple of weeks.
Why: Rear-wheel-drive cars don't send power through the front wheels, so the classic CV-joint click doesn't apply up front. Clicking or popping when turning is more often a strut or shock mount, a ball joint, or loose brake hardware. A shop will usually check each for play.
Possible causes: Worn strut mount or upper bearing; Worn ball joint or tie rod end; Loose brake caliper or pads shifting.
A shop will usually test: Front suspension and steering inspection; Strut mount check; Brake hardware check.
A worn strut mount or its bearing is a likely causeBook a check when convenient
What to do now: Book a front suspension check. Mention that it pops when you turn the wheel at low speed.
Why: On many cars the top of each front strut sits on a mount with a bearing that lets it turn with the steering. When that bearing or rubber mount wears, it can bind and then pop as you turn the wheel, especially when the car is barely moving. A ball joint can make a similar pop, so a shop will usually check both.
Possible causes: Worn strut mount or bearing plate; Worn ball joint; Worn sway bar link or bushing.
A shop will usually test: Strut mount and bearing inspection; Ball joint check; Sway bar link inspection.
That's the turn signal. If it's clicking fast, a bulb may be outSafe to check yourself first
What to do now: Walk around the car with the turn signal on and check each front and rear signal bulb, including the side markers.
Why: The normal turn signal tick comes from a relay or the car's computer. Many cars flash faster on purpose when a bulb is out, to warn you that other drivers can't see your signal.
Possible causes: Burned-out turn signal bulb; Corroded bulb socket or bad connection; Wrong bulb type.
A shop will usually test: Bulb socket and wiring check; Flasher relay test.
Brake pads or a caliper may be shifting slightly when the car changes directionBook a check when convenient
What to do now: Mention it at your next brake service, or book a quick brake check if it's new or getting louder.
Why: Brake pads sit in clips with a tiny bit of room to move. When you switch from Reverse to Drive and brake, the pads can shift and click once. Missing or worn clips, or a loose caliper bolt, can make it louder, so a shop will check the clips and bolts.
Possible causes: Worn or missing pad clips; Loose caliper or bracket bolt; Worn suspension bushing.
A shop will usually test: Brake pad clip and caliper bolt check; Suspension bushing inspection.
Often a CV joint or front suspension part. Have it inspectedBook a check when convenient
What to do now: Book a front axle and suspension check in the next couple of weeks. Note when you hear the click so you can tell the shop.
Why: Clicking when turning usually comes from a worn CV joint or a front suspension part. Where and when it happens tells the shop which one, and a quick inspection on a lift usually confirms it.
Possible causes: Worn outer CV joint; Worn strut mount; Worn ball joint or tie rod end.
A shop will usually test: CV axle and boot inspection; Front suspension and steering inspection.
Related guides
Sources and references: YourMechanic · National Highway Traffic Safety Administration (NHTSA)