Home › Symptom guides › Creaking when turning the wheel
Noise

Why does my car creak or groan when I turn the steering wheel?

A creak or groan when you turn the wheel usually comes from a rubber or metal joint in the steering or front suspension that's dry or worn. Often it's a minor wear item, but some of those joints hold the wheel to the car, so it's worth finding out which one it is. These questions help you tell which is which.

Stop and get help right away if:
  • If the steering suddenly feels loose, the car wanders, or a front wheel looks tilted, pull over and don't drive it.
  • If you hear a loud bang or clunk and the steering changes, stop as soon as it's safe and call for a tow.
  • If the steering suddenly gets very hard to turn, slow down and pull over carefully.
Question 1

Besides the noise, how does the steering feel?

"Loose" means the wheel moves a bit before the car responds, or you're constantly correcting to stay straight.

Full guide: every possible outcome

Prefer to read it all? Here's every result this guide can reach.

A worn steering or suspension joint may be close to failingStop — don't drive it

What to do now: Don't drive it. Have the car towed or have a mobile mechanic inspect the front end.

Why: Creaking plus loose steering or a heavy clunk suggests a ball joint or tie rod end is badly worn. These parts connect the wheels to the car and the steering. If one separates, you can lose control of that wheel.

Possible causes: Badly worn ball joint; Worn tie rod end; Broken coil spring or control arm mount.

A shop will usually test: Ball joint and tie rod inspection with the wheels off the ground; Front suspension inspection on a lift; Wheel alignment check after repairs.

The power steering may not be giving full assistGet it checked in the next few days

What to do now: If your car has a power steering fluid reservoir, check the level with the engine off. Get the steering checked within the next few days, and avoid highway driving and long trips until then.

Why: A groan with heavier steering often means the power steering isn't giving full assist. On cars with hydraulic steering, low fluid or a worn pump are common causes, and a shop will usually find the leak or pressure-test the pump before replacing anything. On electric steering, it can be a motor or sensor fault.

Possible causes: Low power steering fluid from a leak; Worn power steering pump; Electric power steering fault.

A shop will usually test: Power steering fluid and leak inspection; Power steering pump pressure test; Code scan for electric steering faults.

Possibly a dry or worn ball jointGet it checked in the next few days

What to do now: Have the front suspension inspected within the next few days. Until then, avoid potholes, curbs and sharp turns at speed.

Why: Ball joints are pivots that let the front wheels steer and move up and down. When the grease inside dries out or the joint wears, it creaks as it moves, especially when you turn and hit a bump at the same time. A worn ball joint gets worse over time and can eventually separate, so a shop will usually check it for play with the wheels off the ground to tell a dry joint from a worn one.

Possible causes: Worn or dry lower ball joint; Torn ball joint boot; Worn control arm bushing.

A shop will usually test: Ball joint play check with the wheels off the ground; Control arm bushing inspection; Front suspension inspection on a lift.

Possibly dry rubber bushings, often in the sway bar or control armsBook a check when convenient

What to do now: Book a front suspension check when convenient, and mention that it's worse in cold or wet weather.

Why: The suspension uses rubber bushings to cushion metal parts. As they age, they harden and creak when they twist, and cold or wet weather makes it worse. Dry bushings are often more noise than danger, but only an inspection can rule out a worn joint, and worn bushings can affect handling and tire wear over time.

Possible causes: Dry or worn sway bar bushings; Worn control arm bushings; Dry strut mount.

A shop will usually test: Bushing inspection on a lift; Sway bar link and bushing check; Front suspension inspection.

Possibly the tires scrubbing in tight turns, which can be normalSafe to check yourself first

What to do now: Check your tire pressures and set them to the numbers on the sticker inside the driver's door. If you have 4WD or AWD with a selectable mode, make sure it's in 2WD or Auto on dry pavement.

Why: At full lock, the front tires turn at slightly different angles and can scrub on the pavement, which makes a groan, especially on smooth parking garage floors. A 4WD system locked in on dry pavement causes a similar binding or hopping feel. If the noise happens outside those tight turns, it's worth an inspection rather than assuming it's normal.

Possible causes: Normal tire scrub at full lock; 4WD engaged on dry pavement; AWD or differential problem.

A shop will usually test: Wheel alignment check; 4WD or AWD system inspection; Differential fluid check.

Possibly a worn strut mount or strut bearingBook a check when convenient

What to do now: Book a front suspension check when convenient. Mention that the creak or pop happens when turning at low speed.

Why: On many cars, the top of each front strut sits in a mount with a bearing that rotates when you steer. When the bearing wears or the rubber dries out, it creaks, groans or pops as you turn, especially at low speed. It's often not urgent, but it tends to get worse, and a technician should confirm the noise isn't from a ball joint or spring.

Possible causes: Worn strut bearing; Worn strut mount rubber; Worn strut or broken coil spring.

A shop will usually test: Strut mount and bearing inspection; Coil spring inspection; Front suspension inspection on a lift.

The noise may be in the steering column or trim, not the suspensionSafe to check yourself first

What to do now: With the car parked, turn the wheel slowly and see whether the steering wheel cover or the plastic trim around the column is rubbing.

Why: If the creak comes from inside the car, the cause is usually something rubbing in the steering column or the trim around it. Trim rubbing is a comfort issue, but a worn steering shaft joint or clock spring can sound similar, so it's worth having a technician confirm which it is.

Possible causes: Steering wheel or column trim rubbing; Dry or worn steering shaft joint; Worn clock spring.

A shop will usually test: Steering column and shaft inspection; Clock spring check; Airbag system code scan if the light is on.

Have the steering and front suspension inspectedBook a check when convenient

What to do now: Book a front-end inspection when convenient. Record a short video with sound of the creak while turning the wheel to show the technician.

Why: Creaks when turning come from a handful of joints in the steering and suspension. A technician can check them all for wear in a few minutes with the car on a lift.

Possible causes: Worn strut mount or bearing; Dry or worn ball joint; Dry suspension bushings.

A shop will usually test: Front suspension inspection on a lift; Ball joint and tie rod check; Strut mount inspection.

Related guides

Sources and references: Brake & Front End · National Highway Traffic Safety Administration (NHTSA)

This guide helps you understand what may be going on and how urgent it is. It doesn't replace an in-person inspection.