Home › Symptom guides › Reduced engine power / limp mode
Warning light

Why does my car say reduced engine power?

"Reduced engine power" and "limp mode" mean the car's computer has deliberately cut power to protect the engine or transmission, or because it can't trust a sensor. The message itself doesn't say why, so the other signs matter. Answer a few questions to see how serious it is and what's most likely behind it.

Stop and get help right away if:
  • If power drops while you're in traffic, turn on your hazard lights and steer to the shoulder or a side street.
  • If the check engine light is flashing and the engine shakes, pull over and turn the engine off.
  • If the temperature gauge is in the red or there's steam from under the hood, stop and turn the engine off.
  • If you smell burning or see smoke, stop and step away from the car.
Question 1

How much power do you have right now?

Full guide: every possible outcome

Prefer to read it all? Here's every result this guide can reach.

Power is cut too far to drive safelyStop — don't drive it

What to do now: Turn on your hazard lights, get out of traffic and park. Have the car towed or call a mobile mechanic.

Why: When a car can barely move, it's a hazard on any road with traffic. The computer usually cuts power this hard only for a fault it treats as serious, and pushing on can damage the engine or transmission.

Possible causes: Electronic throttle or accelerator pedal sensor failure; Engine overheating protection; Severe transmission fault; Badly clogged exhaust or catalytic converter.

A shop will usually test: Engine and transmission code scan; Throttle and pedal sensor tests; Cooling system check; Exhaust back-pressure test.

The engine may be overheating and cutting power to protect itselfStop — don't drive it

What to do now: Pull over where it's safe and turn the engine off. Don't open the radiator cap while it's hot. Have it towed or call a mobile mechanic.

Why: Some engines reduce power when they get too hot to slow down the damage. Driving an overheating engine can warp or crack major parts in minutes.

Possible causes: Low coolant from a leak; Cooling fan or water pump failure; Stuck thermostat.

A shop will usually test: Cooling system pressure test; Cooling fan and water pump tests; Code scan.

A severe misfire is possible, and it can damage the engine and exhaustStop — don't drive it

What to do now: Pull over where it's safe and turn the engine off. Have the car towed or call a mobile mechanic.

Why: A flashing check engine light usually means the engine is misfiring badly enough to send unburned fuel into the exhaust. That can overheat and ruin the catalytic converter, and the car may cut power because of it.

Possible causes: Failed ignition coil or spark plug; Fuel injector fault; Engine mechanical problem.

A shop will usually test: Code scan and misfire counts; Ignition coil and spark plug tests; Compression test if needed.

The transmission may have a fault that put the car in limp modeGet it checked in the next few days

What to do now: Get off highways and busy roads. Drive only a short, slow distance to a shop if it's close. If it isn't, have it towed.

Why: When the transmission computer sees a problem, it often holds the transmission in one gear and limits power. The car can still move slowly, but it isn't built to be driven this way for long.

Possible causes: Shift solenoid or speed sensor fault; Low or overheated transmission fluid; Wiring or low battery voltage.

A shop will usually test: Transmission code scan; Fluid level and condition check; Solenoid and sensor tests.

The turbo may be losing boost through a leak or faultGet it checked in the next few days

What to do now: Drive gently, avoid hard acceleration and highways, and get it checked within the next few days.

Why: A whoosh or hiss under acceleration often means pressurized air is escaping before it reaches the engine. The computer sees too little boost and cuts power. A split hose or loose clamp is a common cause, and a shop will usually pressure-test the hoses before looking at the turbo itself.

Possible causes: Split or loose boost hose or clamp; Wastegate or boost control fault; Failing turbocharger.

A shop will usually test: Code scan and live boost readings; Boost leak (smoke or pressure) test; Turbo inspection.

The diesel exhaust filter may be clogged with sootGet it checked in the next few days

What to do now: Have a shop check it within the next few days. They can run a forced cleaning cycle. Avoid more short trips until then.

Why: Diesel soot filters clean themselves by burning off soot during longer drives. Lots of short trips stop that from happening, and once the filter is too full, the engine cuts power to protect itself.

Possible causes: Too many short trips; Faulty pressure sensor or hose on the filter; An engine fault making extra soot.

A shop will usually test: Code scan and soot level reading; Forced filter cleaning (regeneration); Filter pressure sensor test.

Often the electronic throttle or gas pedal sensorGet it checked in the next few days

What to do now: Find a safe place to stop, turn the car off for a minute and restart it. Then have the codes read within the next few days, and avoid highways until it's fixed.

Why: On modern cars, the gas pedal is a sensor, and a motor opens the throttle. If the computer gets readings it can't trust from either one, it limits power so the car can't speed up on its own. A dirty throttle, a sensor or a wiring connection are common causes. A shop will usually read the codes and test the sensors and wiring before replacing parts.

Possible causes: Dirty or failing electronic throttle body; Accelerator pedal sensor fault; Wiring or connector problem; Low battery voltage.

A shop will usually test: Code scan; Throttle body inspection and cleaning; Pedal and throttle sensor tests; Wiring and connector check.

A fault that clears with a restart is still a faultGet it checked in the next few days

What to do now: Get the stored codes read within the next few days, before it happens again in traffic.

Why: Restarting resets the computer, so power comes back, but the code that caused it is often still stored. Problems like this tend to return, often at a bad moment.

Possible causes: Electronic throttle or pedal sensor glitch; Loose or corroded wiring connector; Weak battery or charging problem.

A shop will usually test: Code scan, including stored and history codes; Battery and charging test; Throttle and pedal sensor tests.

Related guides

Sources and references: MOTOR · National Highway Traffic Safety Administration (NHTSA)

This guide helps you understand what may be going on and how urgent it is. It doesn't replace an in-person inspection.