Why does my car squeal when I start it or turn the wheel?
A squeal from under the hood at startup, or when you turn the wheel or switch on the A/C, is usually a drive belt slipping on its pulleys. Often it's a simple fix, but the same belt can run the charging system, power steering and water pump. Answer the questions below to see how urgent it is.
- If the temperature gauge climbs toward red or you see steam, pull over and turn the engine off.
- If the steering suddenly gets very heavy while driving, slow down and pull over safely.
- Never reach near the belt or pulleys while the engine is running.
Along with the squeal, is any of this happening?
The drive belt (often called the serpentine belt) is the long ribbed rubber belt on the front or side of the engine. On many cars it turns the alternator, power steering pump and water pump.
Full guide: every possible outcome
Prefer to read it all? Here's every result this guide can reach.
The drive belt may have broken or come offStop — don't drive it
What to do now: Pull over safely and turn the engine off. Have the car towed, or have a mobile mechanic come to you.
Why: On many engines the same belt drives the water pump and power steering. If it slips badly or comes off, the engine can overheat within minutes and steering gets very heavy. Driving on can cause serious engine damage.
Possible causes: Broken or thrown drive belt; Failed tensioner or pulley; Seized water pump or accessory.
A shop will usually test: Belt, tensioner and pulley inspection; Accessory bearing check (water pump, alternator, power steering pump); Cooling system pressure test if it overheated.
The belt may be slipping on the alternator, so the battery may not be chargingGet it checked in the next few days
What to do now: Get it checked within a day. Keep driving to a minimum, turn off accessories like the heated seats and radio, and watch the temperature gauge.
Why: The alternator recharges the battery, and it's turned by the drive belt. A squeal plus the battery light often means the belt is slipping or the alternator is struggling. If so, the car is running on battery power, which won't last long. A shop will usually test charging output and the belt tension before replacing the alternator.
Possible causes: Worn or loose drive belt; Weak belt tensioner; Failing alternator.
A shop will usually test: Charging system output test; Belt and tensioner inspection; Alternator bearing check.
The belt may be coming apart, or a pulley may be failingStop — don't drive it
What to do now: Turn the engine off. Have the car towed, or have a mobile mechanic inspect and repair it where it's parked.
Why: A frayed or slapping belt can come off at any moment, taking out charging, power steering and often cooling at once. A loose strand can also wrap around other parts and damage them.
Possible causes: Worn-out belt; Misaligned or wobbling pulley; Failing tensioner.
A shop will usually test: Belt replacement; Pulley alignment check; Tensioner and idler pulley inspection.
The belt may be worn or a bit loose, and slipping until it warms upBook a check when convenient
What to do now: Book a belt and tensioner check when convenient. Mention that it only happens on cold starts.
Why: A cold, stiff belt grips less, and the alternator works hardest right after startup to recharge the battery. If the belt is worn or the tensioner is weak, it slips for a few seconds and squeals. It usually gets worse over time.
Possible causes: Worn or glazed drive belt; Weak automatic tensioner; Battery that needs a lot of recharging.
A shop will usually test: Belt wear check; Tensioner and pulley inspection; Water spray test to tell slipping from pulley misalignment.
The power steering may be loading up a slipping belt, or the fluid may be lowBook a check when convenient
What to do now: With the engine off, check the power steering fluid level if your car has a reservoir, and book a check when convenient.
Why: A hydraulic power steering pump is usually turned by the drive belt. Turning the wheel, especially all the way to one side, makes the pump work hardest. A worn belt or low fluid can make it squeal at that moment.
Possible causes: Worn or loose drive belt; Low power steering fluid; Failing power steering pump.
A shop will usually test: Belt and tensioner inspection; Power steering fluid and leak check; Power steering pump pressure test.
The belt may be slipping when the A/C compressor kicks onBook a check when convenient
What to do now: Book a belt and A/C check when convenient. Mention that the squeal starts when the A/C or defroster turns on.
Why: When the A/C compressor engages, it adds a sudden load to the belt. A worn belt or weak tensioner can slip for a moment and squeal. The defroster often runs the A/C too, which is why it can happen in winter.
Possible causes: Worn belt or weak tensioner; A/C compressor clutch or bearing problem; A/C compressor starting to seize.
A shop will usually test: Belt and tensioner inspection; A/C compressor clutch and bearing check; A/C pressure check.
The belt may be slipping under loadBook a check when convenient
What to do now: Book a belt and tensioner check within the next couple of weeks.
Why: Revving the engine makes the belt speed up quickly, and accessories resist that change. A belt that's worn, stretched or not held tight enough slips briefly and squeals.
Possible causes: Worn or stretched belt; Weak tensioner; Oil or coolant on the belt.
A shop will usually test: Belt inspection; Tensioner test; Leak check near the belt.
A pulley, tensioner or accessory bearing may be wearing outGet it checked in the next few days
What to do now: Get it checked within a few days. Keep trips short until then.
Why: A squeal or chirp that never stops usually isn't just a cold belt. A pulley or bearing that's starting to drag, or a pulley that's out of line, makes the belt squeal constantly. If that bearing seizes, the belt can come off.
Possible causes: Worn idler or tensioner pulley bearing; Misaligned pulley; Failing accessory bearing (alternator, water pump, A/C).
A shop will usually test: Engine-running stethoscope check of each pulley; Pulley alignment check; Tensioner and idler bearing inspection.
Water on the belt may be making it slip for a momentSafe to check yourself first
What to do now: If it clears up within a few minutes once the belt dries, it's often just water on the belt. Keep an ear on it and mention it at your next service.
Why: Water reduces the grip between the belt and pulleys, so it can slip and squeal briefly after rain or puddles. A belt in good shape usually goes quiet once it dries. A worn belt gets noisier in wet weather first.
Possible causes: Water splashed on the belt; Worn belt that slips easily.
A shop will usually test: Belt and tensioner inspection if it continues.
Often a drive belt that needs a checkBook a check when convenient
What to do now: Book a belt and tensioner check when convenient. Note when the squeal happens so you can tell the shop.
Why: Many squeals from under the hood come from the drive belt slipping or a pulley wearing out. An inspection can usually pinpoint which part is making the noise.
Possible causes: Worn or loose drive belt; Weak tensioner or worn pulley; Power steering or A/C load.
A shop will usually test: Belt, tensioner and pulley inspection; Charging system check.
Related guides
Sources and references: Gates TechZone · Dayco Aftermarket