Home › Symptom guides › Traction control light on
Warning light

Why is my traction control light on?

The traction or stability control light (usually a car with wavy skid marks behind it) does two different jobs. A quick flash while driving on a slippery road usually means the system is working. A light that stays on usually means it's been switched off or has found a fault, and the other lights on the dash often help show why.

Stop and get help right away if:
  • If the red BRAKE light is on too, or the brake pedal feels soft, don't drive it until the brakes are checked.
  • If the check engine light is flashing and the engine shakes or runs rough, pull over safely and turn the engine off.
  • With traction or stability control off, slow down and leave extra room on wet, snowy or icy roads.
Question 1

What is the light doing?

Depending on the car, it may be called TCS, ESC, ESP, VSC, VSA, DSC or StabiliTrak. They all control wheel spin and skids.

Full guide: every possible outcome

Prefer to read it all? Here's every result this guide can reach.

The system is likely doing its job on a slippery roadSafe to check yourself first

What to do now: Ease off the gas, steer smoothly, and slow down for the conditions. The light usually goes out once the tires have grip again.

Why: When a wheel starts to spin or the car starts to slide, the system brakes that wheel or cuts engine power for a moment. The light flickers to tell you it's stepping in, which means the road is slippery.

Possible causes: Wheel spin on a slippery surface; Worn tires.

A shop will usually test: Tire inspection.

Traction or stability control has been switched offSafe to check yourself first

What to do now: Press the traction control button (often a car with skid marks and the word OFF) once, or turn the car off and restart it. Most systems turn back on at startup.

Why: Most cars let you switch traction control off, which is useful when stuck in snow or mud. The OFF light usually just shows it's switched off. It's easy to press the button by accident.

Possible causes: Button pressed by accident; Stuck button; System fault shown as OFF.

A shop will usually test: Stability control code scan; Switch test.

The system may be stepping in when it shouldn't, often from a bad sensor readingGet it checked in the next few days

What to do now: Get the stability control system scanned within a few days. Until then, allow extra time when pulling into traffic, because the car may cut power without warning.

Why: The system compares wheel speeds and steering angle to detect skids. If a sensor sends a wrong reading, or one tire spins at a different speed, the system can think the car is sliding and brake a wheel or cut power on a dry road. A shop will usually watch live sensor data on a test drive before replacing a sensor.

Possible causes: Faulty wheel speed sensor; Mismatched or underinflated tire; Steering angle or yaw sensor reading wrong.

A shop will usually test: Stability control and ABS code scan; Live wheel speed and steering angle data on a test drive; Steering angle sensor calibration.

Traction, ABS and red brake lights together can point to a brake system problemStop — don't drive it

What to do now: Don't drive it. Check that the parking brake is fully released and look at the brake fluid level, then have it towed or call a mobile mechanic.

Why: Traction and stability control rely on the ABS system. When the red brake light joins them, fluid may be low or the system that balances front and rear braking may not be working. The car can skid or spin in a hard stop, and low fluid can also mean a leak or very worn brakes.

Possible causes: Low brake fluid; ABS module or wheel speed sensor fault; Parking brake not fully released.

A shop will usually test: ABS and brake system code scan; Brake fluid leak inspection; Wheel speed sensor check.

A wheel speed sensor fault may have switched off ABS and traction controlGet it checked in the next few days

What to do now: Get the ABS codes read within the next few days. Until then, brake earlier and leave extra room, especially in rain or snow, and pay attention to how the brakes feel.

Why: Traction control, stability control and ABS all use the same wheel speed sensors. When one stops sending a signal, the car switches these systems off and lights the warnings. Regular braking is designed to keep working without ABS, but the wheels can lock in a hard stop, so allow more distance. A shop will usually check live sensor data and the wiring before replacing a sensor.

Possible causes: Failed wheel speed sensor; Damaged sensor wiring; ABS module fault.

A shop will usually test: ABS code scan; Live wheel speed sensor data; Sensor wiring inspection.

The engine may be misfiring, and traction control has shut off as a resultStop — don't drive it

What to do now: Pull over safely and turn the engine off. Have the car towed or call a mobile mechanic.

Why: A flashing check engine light usually means a misfire bad enough to overheat and damage the catalytic converter. Many cars switch traction control off when the engine has a serious fault, because they can't control engine power reliably.

Possible causes: Failed ignition coil or spark plug; Fuel injector problem; Serious engine mechanical problem.

A shop will usually test: Engine code scan; Misfire diagnosis (coils, plugs, injectors); Compression test if needed.

An engine fault may have switched off traction controlGet it checked in the next few days

What to do now: Have the engine codes read within a few days. Many auto parts stores can read basic codes for you.

Why: Traction control works partly by reducing engine power. When the engine computer finds a fault, many cars switch traction control off as a precaution. Fixing the engine fault often turns the traction light off too.

Possible causes: Engine sensor or emissions fault; Throttle or accelerator pedal sensor fault; Shared wiring or voltage problem.

A shop will usually test: Engine and stability control code scan; Throttle system check; Battery and charging test.

The steering angle sensor may need to be reset or calibratedBook a check when convenient

What to do now: Check your owner's manual for a reset step, such as turning the wheel fully left and right with the engine running. If that doesn't work, book a calibration.

Why: Stability control needs to know where the steering wheel is pointed. After the battery is disconnected or the wheels are aligned, some cars lose that setting and turn the light on until the sensor is reset.

Possible causes: Steering angle sensor lost calibration; Steering wheel off-center after an alignment; Faulty steering angle sensor.

A shop will usually test: Stability control code scan; Steering angle sensor calibration; Wheel alignment check.

Mismatched or low tires can confuse the systemSafe to check yourself first

What to do now: Check all four tire pressures and set them to the door-sticker values. If a compact spare is on, get the regular tire back on soon.

Why: The system compares how fast each wheel turns. A low tire, a smaller spare, or tires with very different wear spin at a different speed, which can look like wheel slip and turn the light on.

Possible causes: Underinflated tire; Compact spare in use; Mismatched tire sizes or wear.

A shop will usually test: Tire size and tread depth check; Stability control code scan.

Traction and stability control may have switched off because of a faultGet it checked in the next few days

What to do now: Get the stability control and ABS codes read within the next few days. Until then, drive more gently, leave extra room, especially on slippery roads, and pay attention to how the brakes feel.

Why: A steady traction or stability light without the word OFF usually means the system found a fault and turned itself off. The car won't get the system's help if a wheel spins or the car starts to slide. A scan shows which sensor or circuit to test next.

Possible causes: Wheel speed sensor fault; Steering angle sensor fault or calibration; Engine or throttle fault.

A shop will usually test: Stability control, ABS and engine code scan; Wheel speed and steering angle sensor data.

Related guides

Sources and references: Nissan · National Highway Traffic Safety Administration (NHTSA)

This guide helps you understand what may be going on and how urgent it is. It doesn't replace an in-person inspection.