Acura Integra / RSXproblems, repair costs and recalls
Problems reported across 1996–2024. Pick your model year below to see what applies to your vehicle.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems
33 documented issues across all years, most serious first.
Sticky or notchy steering (recall)
- What you'll notice
- The steering feels sticky or notchy, takes extra effort, or doesn't return to center on the highway. Some owners notice it more in cold weather.
- Why it happens
- The steering gearbox may have been built with too much internal friction. Recall 24V-744 covers 2023-2025 Integra and 2024-2025 Integra Type S, and Acura bulletin 24-037 describes the repair.
- What to do
- Check your VIN for open recalls. A dealer will replace the worm gear spring and regrease the gearbox for free.
Free at an Acura dealer under recall 24V-744.
Stability control unit may leak brake fluid (recall)
- What you'll notice
- The brake pedal travels further than usual, or the car creeps while Brake Hold is on.
- Why it happens
- A ball valve in the vehicle stability assist (VSA) unit can leak brake fluid. Recall 23V-430 covers the 2023 Integra.
- What to do
- Check your VIN for open recalls; the dealer replaces the VSA modulator for free. Don't rely on Brake Hold until it's fixed.
Free under recall 23V-430.
Cranks but won't start (fuel pump main relay)
- What you'll notice
- The engine turns over but won't fire, often when the car is hot or after it has sat in the sun. It may start again once it cools down. You may not hear the fuel pump hum when you turn the key.
- Why it happens
- The main relay that powers the fuel pump and injectors develops cracked solder joints with age and heat, so it stops sending power. RepairPal has more than 80 owner reports of this no-start on the Integra.
- What to do
- Have a shop check for fuel pump power while the problem is happening. A new or resoldered main relay is a cheap fix; don't let anyone replace the fuel pump until the relay has been ruled out.
Distributor failure: stalling or no spark
- What you'll notice
- The engine misfires, stalls while driving, or cranks without starting. It often happens on high-mileage cars and may come and go at first.
- Why it happens
- The distributor houses the ignition coil and igniter, which wear out with heat and age. Owners report replacing the whole distributor, not just the cap and rotor.
- What to do
- Have the ignition system tested for spark. Replacing the cap and rotor is cheap maintenance, but a failed coil or igniter usually means a new or remanufactured distributor.
Radiator cracks and leaks coolant
- What you'll notice
- Green coolant under the front of the car, a sweet smell, the low coolant level, or the temperature gauge rising.
- Why it happens
- The plastic radiator tanks become brittle with age and crack, especially on high-mileage cars. Owners report radiator failures at around 180,000 km.
- What to do
- Don't drive if the engine is overheating. Replace the radiator and check the hoses and cap at the same time.
Alternator stops charging
- What you'll notice
- The battery light comes on, lights dim, or the battery keeps going dead.
- Why it happens
- The alternator wears out with age and mileage. Owners of these cars report alternator replacements.
- What to do
- Have the charging system tested. Replace the alternator if output is low, and check the battery since a weak one adds strain.
Manual transmission grinds or pops out of 3rd gear
- What you'll notice
- Grinding when shifting into 2nd or 3rd, especially on quick shifts, 3rd gear that is hard to get into, or the shifter popping out of 3rd. It usually starts mild and gets worse.
- Why it happens
- The 3rd gear synchronizer or the 3-4 shift sleeve wears. Acura Service Bulletin 08-018 covers this on the 6-speed, and earlier bulletins covered gear grinding on these manuals.
- What to do
- Try fresh Honda manual transmission fluid first; it sometimes helps. If grinding continues, the transmission needs a rebuild with new synchros. Shift gently to slow the wear.
A/C stops blowing cold (compressor failure)
- What you'll notice
- The air conditioning blows warm or cycles on and off, sometimes with noise from the compressor.
- Why it happens
- The A/C compressor or its clutch fails on many of these cars, and leaks in the system are common. Owners report this can be a costly repair.
- What to do
- Have the system checked for leaks and pressure. A failed compressor is usually replaced along with the drier and a system flush.
Check engine light from the VTC oil control valve
- What you'll notice
- The check engine light comes on, sometimes with rough idle or less power. Codes often relate to cam timing.
- Why it happens
- The oil control valve that runs the variable valve timing (VTC) can stick or get clogged with debris. An Acura bulletin covers VTC faults from a contaminated or stuck solenoid. RepairPal reports it at about 72,500 miles on average.
- What to do
- Have the codes read. Change the oil if it's overdue, then clean or replace the VTC oil control valve and its screen.
Timing chain or tensioner rattle and cam timing codes
- What you'll notice
- A rattle from the engine, often at startup, and a check engine light with cam or crank timing codes.
- Why it happens
- An Acura bulletin covers timing-related codes from the timing chain, tensioner, sprocket or low oil pressure. The tensioner wears and lets the chain slap.
- What to do
- Have the codes and oil pressure checked. Replace the tensioner, and the chain if it's stretched, before it can jump a tooth.
Clutch master cylinder squeaks, then fails
- What you'll notice
- The clutch pedal squeaks, then feels soft, sticks to the floor, or the car is hard to shift because the clutch doesn't fully release.
- Why it happens
- The clutch master cylinder wears internally. Acura issued a bulletin for clutch pedal squeak, and owners report master and slave cylinder failures.
- What to do
- Check the clutch fluid level. Have the hydraulics bled or the master cylinder replaced; owners recommend flushing the fluid regularly.
Broken engine or transmission mount
- What you'll notice
- Clunking when shifting or getting on and off the gas, and more vibration in the cabin at idle.
- Why it happens
- The rubber in the engine and transmission mounts tears with age. TrueDelta owners report both failing.
- What to do
- Have the mounts inspected. Replacing a torn mount stops the clunk and protects the exhaust and axles.
Starter clicks or won't crank
- What you'll notice
- You hear a click or nothing when you turn the key, even though the battery is good.
- Why it happens
- The starter motor wears out. It's one of the most-reported RSX repairs on TrueDelta.
- What to do
- Have the battery and cables tested first, then test and replace the starter.
Harsh or noisy automatic downshifts when slowing
- What you'll notice
- The automatic makes a hard or noisy shift from 3rd to 2nd or 2nd to 1st as you slow down, or the D light flashes.
- Why it happens
- Acura issued bulletins for harsh downshifts on these automatics and set rules for replacing shift solenoids. Old fluid makes it worse.
- What to do
- Change the fluid with genuine Honda ATF and have the codes read. Ask a dealer about the related bulletins and software updates.
Driver seat frame may be loose (recall)
- What you'll notice
- The driver's seat feels loose or shifts, especially under braking.
- Why it happens
- The driver's seat cushion frame may not have been tightened properly at the factory. Recalls 24V-859 and 26V-054 cover the 2024 Integra.
- What to do
- Check your VIN for open recalls; the dealer replaces the seat cushion frame for free.
Free under recalls 24V-859 and 26V-054.
Oil leak at the distributor and check engine light
- What you'll notice
- Oil on the back of the cylinder head below the distributor, and sometimes a check engine light or rough running if oil gets inside the distributor.
- Why it happens
- The O-ring that seals the distributor to the cylinder head hardens with age and lets oil seep out, and the shaft seal can let oil into the distributor itself. RepairPal lists this for 1990-2001 Integras at about 135,000 miles on average.
- What to do
- Replace the distributor O-ring soon; it's a cheap part. If oil is inside the distributor cap, the distributor seal or the whole unit may need replacing.
Squeal from the distributor that sounds like a loose belt
- What you'll notice
- A loud squeal or chirp from the engine that sounds like a slipping belt, even after the belts are adjusted or replaced.
- Why it happens
- On high-mileage cars the bearing inside the distributor wears out and squeals. RepairPal notes it is often mistaken for a belt problem.
- What to do
- Ask a shop to confirm where the noise comes from with a stethoscope before replacing belts. A worn distributor bearing usually means replacing the distributor.
Rough, high or hunting idle
- What you'll notice
- The idle speed surges up and down, stays too high when warm, or the engine idles roughly.
- Why it happens
- The fast idle thermo valve and the idle air control valve get dirty or loose with age, so the engine computer can't hold a steady idle.
- What to do
- Have the throttle body, fast idle thermo valve and idle air control valve cleaned. Replace the idle air control valve if cleaning doesn't help, and check for vacuum leaks.
Oil leaks from the valve cover gasket and cam plug
- What you'll notice
- Oil on top of or around the engine, a burning oil smell after driving, or oil drips on the transmission side.
- Why it happens
- The rubber valve cover gasket and the O-ring on the plastic camshaft end plug harden with age and start to seep.
- What to do
- Replace the valve cover gasket and cam plug O-ring together. Both are inexpensive and stop oil from dripping on hot exhaust parts.
Sunroof leaks water inside
- What you'll notice
- Water drips from the headliner, the dome light area or down the pillars after rain or a car wash.
- Why it happens
- The sunroof's drain tubes clog with dirt and leaves, so water overflows into the cabin instead of draining out.
- What to do
- Clear the drain tubes with low air pressure or a flexible line. Dry the carpet promptly to prevent mold and electrical problems.
Knocking from worn rear trailing arm bushings
- What you'll notice
- A metallic knock from the rear on uneven roads, and the rear end may feel loose.
- Why it happens
- The large rubber bushings in the rear trailing arms crack after about 10 years and eventually break.
- What to do
- Have the rear bushings inspected and replaced in pairs. Check ball joints and tie rods at the same time; owners say they wear on these cars too.
Temperature gauge reads low or stops moving
- What you'll notice
- The temperature gauge slowly reads lower than normal, then the needle may stop moving at all, even though the engine is warm.
- Why it happens
- The single-wire coolant temperature sender for the dashboard gauge wears out. It's separate from the sensor the engine computer uses.
- What to do
- Make sure the engine actually warms up and the thermostat works. Replacing the gauge sender is inexpensive.
Burns some oil between changes
- What you'll notice
- The oil level drops between changes, sometimes with a little blue smoke on startup.
- Why it happens
- Owners say slight oil burning is common on high-revving Integra engines, and some RSX Type-S owners report the same. Worn rings or valve seals make it worse with age.
- What to do
- Check the oil level every other fill-up and top it off. If you're adding more than about a quart every 1,000 miles, have a compression and leak-down test done.
Water in the trunk from leaking taillight seals
- What you'll notice
- Water pools in the trunk or spare tire well, or moisture shows inside the taillights.
- Why it happens
- The rubber gaskets behind the taillights harden and shrink with age and let water in. Owners report it on both Integras and RSXs.
- What to do
- Replace the taillight gaskets or reseal the housings. Dry out the trunk to stop rust and musty smells.
Check engine light from a failed EVAP purge valve
- What you'll notice
- The check engine light comes on with an evaporative emissions code. The car usually drives normally.
- Why it happens
- The purge valve that sends fuel vapor into the engine fails. RepairPal reports it at about 94,000 miles on average.
- What to do
- Check the gas cap first. If the code returns, replace the purge valve; it's not urgent but the car may fail an emissions test.
Power window cable snaps or window sticks
- What you'll notice
- The window drops into the door, moves slowly or crooked, makes a grinding noise, or the auto-up stops working.
- Why it happens
- The cables in the window regulator fray and break. Owners report a moderately expensive repair.
- What to do
- Tape the window up if it falls, then replace the regulator. Clean and lubricate the window channels to reduce strain.
Power door locks won't lock or unlock
- What you'll notice
- One door won't lock or unlock with the switch or remote, or it makes a buzzing sound.
- Why it happens
- The door lock actuators wear out. Acura issued a bulletin for power locks that won't work.
- What to do
- Have the failing door's actuator replaced. Use the key in the meantime.
Check engine light from a failed oxygen sensor
- What you'll notice
- The check engine light comes on, and fuel economy may drop.
- Why it happens
- The upstream air-fuel (oxygen) sensor is the most-reported failure on the RSX. Owners say it often fails around 80,000-100,000 miles.
- What to do
- Have the codes read and replace the failed sensor. Don't ignore it for long; a bad sensor can hurt the catalytic converter.
Exhaust leak or rattle at the header flex joint
- What you'll notice
- A rattle or louder exhaust sound, especially on hard acceleration, and possibly an exhaust smell.
- Why it happens
- Acura bulletins cover exhaust leaks at the flexible joint behind the exhaust header and rattling heat shields.
- What to do
- Have the exhaust inspected. Fix leaks near the engine promptly so fumes don't get into the cabin.
Seat seams split or seat covers come loose
- What you'll notice
- Seat upholstery seams pull apart, or the seat covers come loose near the headrests.
- Why it happens
- The seat covers are a known weak spot. The most-reported RSX complaint on CarComplaints is a seat seam coming apart, and Acura issued bulletins about loose covers at the headrests.
- What to do
- Have an upholstery shop restitch it before the tear spreads, or replace the cover.
Check engine light with code P0011 (valve timing)
- What you'll notice
- The check engine light comes on with code P0011, a cam timing (VTC) fault.
- Why it happens
- Acura Service Bulletin 24-026 says the engine computer doesn't control oil flow to the variable valve timing precisely enough, so the timing overshoots its target.
- What to do
- Check the oil level and top off if low. Have a dealer apply the engine software update from bulletin 24-026.
Door window weatherstrip comes loose
- What you'll notice
- The rubber seal along the door window frame pulls loose or sits out of place, which can cause wind noise.
- Why it happens
- Acura Service Bulletin B23090A covers loose door sash weatherstrips.
- What to do
- Ask a dealer to reinstall or replace the weatherstrip under warranty.
Wipers stop working after blade changes or snow
- What you'll notice
- The windshield wipers stop moving, move out of sync, or make noise after the blades were changed or pulled away from the glass in snow.
- Why it happens
- Acura Service Bulletin B23110A says changing the blade inserts the wrong way, or lifting the arms in snow and ice, can damage the wiper motor linkage.
- What to do
- Follow the owner's manual when changing blades. If the wipers act up, have the linkage checked before driving in rain or snow.
Repair prices for your Acura Integra / RSX
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace PGM-FI main relay
- Replace distributor (new or remanufactured)
- Replace distributor O-ring
- Replace distributor
- Clean throttle body, fast idle valve and idle air control valve
- Replace valve cover gasket and cam plug O-ring
- Replace radiator and refill coolant
- Clear sunroof drain tubes
- Replace rear trailing arm bushings (pair)
- Replace coolant temperature gauge sender
- Replace alternator
- Replace taillight gaskets and reseal
- Replace A/C compressor, drier and recharge
- Clean or replace VTC oil control valve and screen
- Replace EVAP purge valve
- Replace timing chain tensioner
- Replace clutch master cylinder and bleed
- Replace power window regulator
- Replace door lock actuator
- Replace one engine mount
- Replace upstream air-fuel (oxygen) sensor
- Replace starter
- Replace exhaust flex pipe or gasket
- Change transmission fluid and update software
- Update engine software and relearn cam timing
- Reinstall or replace door sash weatherstrip
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Replace steering gearbox worm gear spring and regreaseNo charge if your vehicle is included
- Replace VSA modulatorNo charge if your vehicle is included
- Replace driver seat cushion frameNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Pick a model year to see its safety recalls.