Audi A8problems, repair costs and recalls
Problems reported across 1997–2024. Pick your model year below to see what applies to your vehicle.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems
34 documented issues across all years, most serious first.
Air suspension sags and the compressor wears out
- What you'll notice
- One corner or the whole car sits low after parking, a suspension warning light, the compressor running often or loudly, or a harsh, uneven ride.
- Why it happens
- The air struts leak as their rubber ages, which overworks the compressor until it fails. Ride height sensors can fail too.
- What to do
- Have the system checked for leaks before replacing the compressor, or the new one will fail too. Replacing leaking struts and the compressor together is often the lasting fix.
Timing belt failure bends the valves
- What you'll notice
- The engine suddenly quits and will not restart, sometimes after a ticking or squeal from the front of the engine.
- Why it happens
- The 3.7L and 4.2L V8 engines in these years use a timing belt. Worn belts, tensioners or rollers can let it slip or break, and the engine's valves then hit the pistons.
- What to do
- If there is no record of a belt, tensioner and roller change in the last 100,000 miles or so, have it done now. An independent Audi specialist is often much cheaper than a dealer.
Timing chain and tensioner wear on the 4.2 FSI
- What you'll notice
- A rattle from the engine on cold start, then cam timing codes or rough running if it gets worse.
- Why it happens
- The direct-injection 4.2L V8 has several timing chains with tensioners and guides that wear, usually from around 100,000 miles. The chains are at the back of the engine, so the repair is big.
- What to do
- Do not ignore a startup rattle. Have the cam timing checked; on high-mileage cars, chains and guides are best replaced before they fail.
Automatic transmission shifts harshly or slips
- What you'll notice
- Harsh or delayed shifts, the engine revving between gears, lurching from a stop, or the car not wanting to engage a gear.
- Why it happens
- Old or low fluid, leaks and internal wear of clutches and solenoids in the 5-speed automatic.
- What to do
- Check for fluid leaks and have a transmission scan done. A fluid service or solenoid repair can help if caught early; slipping usually means a rebuild.
Plastic coolant pipe at the oil filter housing leaks
- What you'll notice
- A large coolant leak on the passenger side above the oil pan, a low coolant warning, and a sweet coolant smell.
- Why it happens
- A plastic coolant union pipe on the oil filter housing of the 4.2L V8 cracks with age. The part is cheap but reaching it means taking a lot of the engine apart.
- What to do
- Keep an eye on the coolant level and stop if the engine overheats. Get quotes from an Audi specialist; aluminum replacement pipes are available.
W12 burns oil and builds sludge
- What you'll notice
- The oil level drops quickly between changes, blue smoke, or a low-oil warning.
- Why it happens
- The 6.0L W12 uses a lot of oil and does not tolerate long oil change intervals. Sludge can block oil passages and speed up timing chain wear.
- What to do
- Check the oil often and change it every 5,000-7,500 miles with the correct oil. Have the timing chains checked if you hear rattles.
Coolant pump leaks and coolant level drops
- What you'll notice
- A low coolant warning, coolant falling with no puddle under the car, a check engine light, sometimes a low-boost code (P0299).
- Why it happens
- The coolant pump on the 3.0L V6 can leak, and coolant can contaminate a vacuum switch valve. A 2026 lawsuit says the pump wears out early and can lead to overheating.
- What to do
- Have a pressure test done when the warning appears and do not drive if it overheats. Ask about Audi bulletin 2070349 while under warranty.
Turbo oil strainer can clog and wreck the turbos (recall)
- What you'll notice
- Turbo whine, loss of boost, the engine refusing to idle, or stalling.
- Why it happens
- A blocked oil strainer on the 4.0L twin-turbo V8 starves the turbo bearings, which can break the turbo shaft. Owners report very expensive turbo repairs before the recall.
- What to do
- Check your VIN for open recalls. The dealer replaces the strainer and changes the oil free; if turbos already failed, ask about reimbursement.
High-pressure fuel pump supply line can leak (recall)
- What you'll notice
- A fuel smell from the engine bay.
- Why it happens
- The fuel line feeding the high-pressure pump can become porous and leak, which is a fire risk. A second recall added a pressure damper.
- What to do
- Check your VIN for open recalls and do not drive if you smell fuel.
Fuel rails can leak (recall)
- What you'll notice
- A fuel smell from the engine bay.
- Why it happens
- The left and right fuel rails on the supercharged V6 can leak fuel, which is a fire risk.
- What to do
- Check your VIN for open recalls. The dealer replaces both rails free.
Engine bay seal can touch hot parts (recall)
- What you'll notice
- A loose rubber seal at the edge of the hood or a burning-rubber smell.
- Why it happens
- The engine compartment seal can come loose and rest on hot engine parts, which is a fire risk.
- What to do
- Check your VIN for open recalls. The dealer fits a retaining plate free.
Coolant valve can leak into the engine computer (recall)
- What you'll notice
- Loss of power, stalling, or coolant loss.
- Why it happens
- A leaking coolant valve can let coolant run into the engine control module connector.
- What to do
- Check your VIN for open recalls. The dealer replaces the valve and checks the connector free.
Sunroof glass may come loose (recall)
- What you'll notice
- No warning before failure; the glass panel could separate while driving.
- Why it happens
- The sunroof glass may not be properly bonded to its frame.
- What to do
- Check your VIN for open recalls. The dealer adds adhesive between the glass and frame free.
Sunroof glass can shatter (recall)
- What you'll notice
- Cracks in the sunroof glass or the panel breaking.
- Why it happens
- On cars built in mid-2013, the standard sunroof glass panel can shatter.
- What to do
- Check your VIN for open recalls. The dealer replaces the glass free.
Driver or passenger airbag may not work correctly (recall)
- What you'll notice
- An airbag warning light, or no sign at all before a crash.
- Why it happens
- On 2004-2005 cars the driver airbag may not unfold properly. On 2006-2007 cars a wiring issue or a weak battery can switch the passenger airbag off when it should be on.
- What to do
- Check your VIN for open recalls. Dealers replace the airbag, modify the wiring or update the airbag computer free.
Shifter can leave Park without the key (recall)
- What you'll notice
- The gear lever can be moved out of Park without the key in the ignition, and the car could roll away.
- Why it happens
- The automatic transmission's locking cable can shift out of position.
- What to do
- Always set the parking brake. Check your VIN for open recalls; the dealer installs an adjusting piece free.
Driver airbag can go off from static shock (recall)
- What you'll notice
- In very dry weather, the driver airbag could deploy when the driver touches the steering wheel.
- Why it happens
- Static electricity could trigger the airbag's firing circuit.
- What to do
- Check your VIN for open recalls. The dealer installs a ground wire free.
Driver airbag inflator can absorb moisture (recall)
- What you'll notice
- No warning before a crash.
- Why it happens
- Moisture can get into the driver airbag inflator, so it may burst or underinflate in a crash.
- What to do
- Check your VIN for open recalls right away and have the inflator replaced free.
Moisture in engine computer connector can stall the engine (recall)
- What you'll notice
- Warning lights, rough running, or the engine stalling.
- Why it happens
- A missing sealing pin lets moisture into the engine control module connector.
- What to do
- Check your VIN for open recalls. The dealer installs the pin and replaces corroded connectors free.
Rear trailing arm nut can break (recall)
- What you'll notice
- The car pulls or tracks oddly, or the rear tires wear unevenly.
- Why it happens
- The lock nut on a rear trailing arm can crack from stress corrosion and misalign the rear axle. A follow-up recall checks alignment on repaired cars.
- What to do
- Check your VIN for open recalls. The dealer replaces the nuts and checks alignment free.
Passenger airbag may deploy too forcefully (recall)
- What you'll notice
- No warning before a crash.
- Why it happens
- The front passenger airbag may be folded wrongly and inflate with too much force.
- What to do
- Check your VIN for open recalls. The dealer replaces the airbag module free.
Front passenger airbag may switch off (recall)
- What you'll notice
- The passenger airbag 'off' light shows with an adult in the seat.
- Why it happens
- A loose connection at the passenger occupant detection module can turn off the airbag.
- What to do
- Check your VIN for open recalls. The dealer replaces the module free.
MMI screen freezes, dims or won't boot
- What you'll notice
- The MMI infotainment screen locks up, goes dim or black, the navigation will not load, the radio and settings stop responding, or on 2011-2018 cars the pop-up screen sticks and will not open or close.
- Why it happens
- Early MMI units suffer hard drive and screen failures with age and need software updates; the later retractable screen's mechanism and software can also fail.
- What to do
- Try a system reset and ask about software updates first. If hardware has failed, a used or rebuilt unit can be coded to the car.
Oil leaks from valve cover and camshaft seals
- What you'll notice
- Oil spots under the car, a burning-oil smell after a drive, oily residue on the engine, and the oil level falling between changes.
- Why it happens
- Valve cover gaskets, camshaft seals and oil pan gaskets on these V8s harden with age. A clogged crankcase vent (PCV) can push oil past them faster.
- What to do
- Have the leak traced and the gaskets replaced before oil drips onto the exhaust. Check the crankcase vent at the same time.
Carbon buildup on the intake valves
- What you'll notice
- Rough idle, misfires and a gradual loss of power, sometimes with a check engine light.
- Why it happens
- On direct-injection engines fuel never washes the intake valves, so oil vapor bakes onto them and restricts airflow, typically from about 60,000-80,000 miles.
- What to do
- If misfires persist after coils and plugs, ask for the intake valves to be inspected and walnut-blasted.
Control arm bushings and ball joints wear
- What you'll notice
- Clunks over bumps, vague or wandering steering, and uneven tire wear.
- Why it happens
- The many aluminum control arms in the front suspension have rubber bushings and ball joints that wear out, often around 60,000-80,000 miles.
- What to do
- Have the front suspension checked for play and replace worn arms, then get an alignment.
Oil leaks from the cylinder head cover
- What you'll notice
- Oil level dropping, a burning-oil smell, and oil residue around the valve covers or under the car.
- Why it happens
- Audi found metal shavings left in the cylinder head cover sealing groove at the factory, causing leaks around the cover, injectors and valve-lift actuator.
- What to do
- Have it resealed before oil reaches the hot exhaust, and mention Audi bulletin 2053278.
Fuel filler neck can leak fuel vapor (recall)
- What you'll notice
- A fuel smell near the filler door.
- Why it happens
- The filler neck's cover may not seal, letting fuel vapor escape.
- What to do
- Check your VIN for open recalls. The dealer replaces the filler neck and expansion tank free.
Rear camera screen blank from infotainment fault (recall)
- What you'll notice
- A black or blank screen instead of the camera image when reversing.
- Why it happens
- Software errors, and on some cars damage inside the infotainment unit at shutoff, can stop the camera image from appearing.
- What to do
- Check your VIN for open recalls. The dealer updates the software or replaces the unit free.
Rear camera image may not display (recall)
- What you'll notice
- The rear camera picture is missing or wrong when reversing.
- Why it happens
- A software error can stop the rearview camera image from displaying.
- What to do
- Check your VIN for open recalls. The dealer updates the software free.
Water pump and thermostat housing leak coolant
- What you'll notice
- Coolant level slowly dropping, a sweet smell after driving, pink or white crust on the front of the engine, or a low coolant warning.
- Why it happens
- The plastic water pump and thermostat housing on the supercharged 3.0L V6 develop leaks, mostly on higher-mileage cars.
- What to do
- Have the cooling system pressure tested. Replace the leaking pump or housing before the engine overheats.
Sunroof drains clog and leak water inside
- What you'll notice
- Damp carpets, water dripping from the headliner or pillars, or a musty smell after rain.
- Why it happens
- The drain tubes at the corners of the sunroof tray clog with debris, so rainwater overflows into the cabin.
- What to do
- Have the drains cleared and tested. Dry wet carpets quickly, since water can damage modules and wiring under them.
Crankcase vent (PCV) valve fails
- What you'll notice
- An oil smell, rough idle, whistling from the engine, or oil use between changes.
- Why it happens
- The crankcase vent and oil separator on the supercharged V6 and twin-turbo V8 wear out with age.
- What to do
- Have the PCV valve and oil separator checked if the engine idles rough or smells of oil; many owners replace it around 80,000 miles.
Brief rattle on cold start from the 3.0T
- What you'll notice
- A rattle lasting 1-3 seconds from the back of the engine on the first cold start of the day.
- Why it happens
- Audi traced it to an upper timing chain tensioner. Audi says it does not cause damage.
- What to do
- Ask the dealer about bulletin 2039995, which installs improved tensioners on both sides.
Repair prices for your Audi A8
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace leaking air strut(s) and compressor
- Replace timing belt, tensioner, rollers and water pump
- Replace timing chains, guides and tensioners
- Replace and code MMI unit
- Replace valve cover gaskets (both banks)
- Transmission fluid service and solenoid/leak repair
- Replace coolant union pipe at oil filter housing
- Replace front control arm(s) and align
- Replace coolant pump and clean contaminated vacuum parts
- Reseal cylinder head (valve) covers
- Replace water pump and thermostat housing
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Dealer recall repairNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Pick a model year to see its safety recalls.