BMW 4 Seriesproblems, repair costs and recalls
Problems reported across 2014–2026. Pick your model year below to see what applies to your vehicle.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems
32 documented issues across all years, most serious first.
Timing chain guides break on the 2.0L turbo
- What you'll notice
- A whine or rattle from the front of the engine, worst on cold starts, timing or camshaft fault codes, a Drivetrain Malfunction warning, or sudden loss of power and stalling.
- Why it happens
- The plastic timing chain guides on the early 428i's 2.0L turbo engine turn brittle and break. The chain can then go slack, skip teeth or snap, which can destroy the engine. Cars built after about February 2015 got revised parts.
- What to do
- If you hear a whine or rattle, stop driving it hard and get it inspected right away. Ask for records showing updated chain parts were installed. BMW's extended coverage and a class-action settlement have aged out for most cars, but a dealer can check your VIN.
Electric water pump or thermostat fails and the engine overheats
- What you'll notice
- Engine temperature warning, the radiator fan running hard all the time, a reduced-power mode, coolant leaks or a drained battery. A common fault code is 2E83.
- Why it happens
- These engines use an electric water pump that wears out, usually between 50,000 and 100,000 miles. The thermostat is a weak point too and can stick.
- What to do
- If the temperature warning comes on, pull over and shut the engine off; driving an overheating engine can ruin it. Replace the thermostat along with the pump.
M4 crank hub can spin and knock timing out
- What you'll notice
- Sudden limp mode, a Drivetrain Malfunction warning, hard starting, rough idle, a check engine light and timing or VANOS codes.
- Why it happens
- On the S55 engine in the 2015-2020 M4, the crank hub is held only by friction and can spin on the crankshaft, throwing off engine timing. It is rare on stock cars and more likely on tuned ones.
- What to do
- Stop driving if timing warnings appear; running it can damage the engine. Owners of tuned cars often install a locking or keyed crank hub kit.
Water pump connector can short and start a fire (recall)
- What you'll notice
- Coolant temperature or water pump warnings, or a burning or electrical smell from the engine bay.
- Why it happens
- The electrical connector on the 2.0L turbo's water pump isn't sealed well enough. Water can get in and short it, which could start a fire.
- What to do
- Check your VIN for recall 24V-608 and park outside until it's fixed. The dealer inspects the pump and connector and adds a protective shield.
Free at a BMW dealer under the recall. Ask the dealer to check your VIN for open recalls.
Fuel pump can fail and stall the engine (recall)
- What you'll notice
- Hard starting, stalling, misfires, hesitation or a Drivetrain Malfunction warning.
- Why it happens
- Bad plating inside the in-tank fuel pump can make it fail, and the engine can stall without warning.
- What to do
- Have a dealer confirm recall 15V-189 is done. Fuel pumps can also wear out normally over time.
Free at a BMW dealer under the recall. Ask the dealer to check your VIN for open recalls.
Brake vacuum pump can fail and the pedal gets hard (recall)
- What you'll notice
- The brake pedal becomes hard and the car takes more effort to stop.
- Why it happens
- Poor lubrication can make the engine-driven brake vacuum pump fail, reducing power braking assist on 2014 428i coupes.
- What to do
- If the pedal suddenly feels hard, drive carefully to a dealer and ask about recall 14V-627.
Free at a BMW dealer under the recall. Ask the dealer to check your VIN for open recalls.
Side curtain airbag inflator weld can fail (recall)
- What you'll notice
- None before a crash.
- Why it happens
- The weld on the head (curtain) airbag inflator can fail, so the airbag may leak and inflate weakly, or the inflator can rupture and throw metal pieces.
- What to do
- Have a dealer replace the head airbags under recall 24V-288 as soon as possible.
Free at a BMW dealer under the recall. Ask the dealer to check your VIN for open recalls.
Driver airbag inflator can rupture (recall)
- What you'll notice
- None before a crash.
- Why it happens
- A manufacturing defect can make the driver's front airbag inflator burst when it deploys, sending sharp metal pieces toward people inside.
- What to do
- Get the driver's airbag replaced under recall 24V-527 right away.
Free at a BMW dealer under the recall. Ask the dealer to check your VIN for open recalls.
M4 driveshaft can fail and cut power (recall)
- What you'll notice
- A sudden loss of power to the rear wheels, often with a bang or vibration from under the car.
- Why it happens
- Some M4 driveshafts left the factory without grease in the slip joint (2015-2016), and on 2016-2017 cars the joint between driveshaft and flange can fail.
- What to do
- Check your VIN for both driveshaft recalls (including 18V-713). The dealer replaces the driveshaft for free.
Free at a BMW dealer under the recall. Ask the dealer to check your VIN for open recalls.
Seat side airbags may not inflate (recall)
- What you'll notice
- None before a crash.
- Why it happens
- The igniter in the seat-mounted side airbags may not fire in a crash.
- What to do
- Have the dealer replace the seat airbag modules under recalls 16V-914 and 17V-115.
Free at a BMW dealer under the recall. Ask the dealer to check your VIN for open recalls.
Convertible front seat belts may not lock (recall)
- What you'll notice
- None before a crash.
- Why it happens
- Parts inside the front seat belt retractors on 2018 4 Series convertibles may not match, so the belt might not lock in a crash.
- What to do
- Have the dealer inspect and replace the belts under recall 17V-507.
Free at a BMW dealer under the recall. Ask the dealer to check your VIN for open recalls.
Crankshaft sensor software can stall the engine (recall)
- What you'll notice
- The engine stalls while driving.
- Why it happens
- Some 2019 430i and 440i models got a crankshaft sensor with the wrong firmware, which can make the engine stall.
- What to do
- Have the dealer replace the sensor under recall 18V-465.
Free at a BMW dealer under the recall. Ask the dealer to check your VIN for open recalls.
Knee airbags may not inflate correctly (recall)
- What you'll notice
- None before a crash.
- Why it happens
- The driver and passenger knee airbags may have been folded and assembled incorrectly.
- What to do
- Have the dealer replace the knee airbag modules under recall 19V-352.
Free at a BMW dealer under the recall. Ask the dealer to check your VIN for open recalls.
M4 fuel injectors can damage the fuel line (recall)
- What you'll notice
- A fuel smell from the engine bay.
- Why it happens
- Some 2020 M4 injectors were missing a part that damps vibration, which can damage the fuel line and cause a fire risk.
- What to do
- Have the dealer inspect the injectors and replace them and the fuel rail if needed under recall 20V-666.
Free at a BMW dealer under the recall. Ask the dealer to check your VIN for open recalls.
Passenger seat belt locking mode can switch off early (recall)
- What you'll notice
- None you can notice in normal driving.
- Why it happens
- The passenger seat belt's automatic locking retractor (used for child seats) may turn off before the belt fully retracts.
- What to do
- Have the dealer inspect the belts under recall 21V-554.
Free at a BMW dealer under the recall. Ask the dealer to check your VIN for open recalls.
48-volt battery connection can overheat (recall)
- What you'll notice
- Usually none. Possibly a burning smell or electrical warnings.
- Why it happens
- On the M440i's mild-hybrid system, the connection between the 48-volt battery and the starter-generator may be assembled poorly, raising resistance and fire risk.
- What to do
- Have the dealer inspect and fix the connection under recall 20V-761.
Free at a BMW dealer under the recall. Ask the dealer to check your VIN for open recalls.
M4 integrated brake unit can come apart under hard braking (recall)
- What you'll notice
- Brake warnings or loss of brake assist, especially under hard braking.
- Why it happens
- A rotor and shaft inside the integrated brake system of 2021 M4s may not be welded properly and could separate.
- What to do
- Have the dealer replace the integrated brake system under recall 21V-062.
Free at a BMW dealer under the recall. Ask the dealer to check your VIN for open recalls.
Starter relay can corrode and short out (recall)
- What you'll notice
- The car sometimes won't start, or there's a burning smell near the starter.
- Why it happens
- The starter relay on the 430i's 2.0L engine can corrode, overheat and short, raising fire risk.
- What to do
- Park outside and away from buildings until the dealer replaces the starter under recall 25V-636.
Free at a BMW dealer under the recall. Ask the dealer to check your VIN for open recalls.
Starter can overheat and catch fire (recall)
- What you'll notice
- Trouble starting, a burning smell, or smoke near the engine after starting.
- Why it happens
- Wear inside the starter can make it overheat. Recall 26V-056 covered 2021-2024 cars, and 26V-438 expanded it.
- What to do
- Check your VIN for both starter recalls and park outside until the starter is replaced.
Free at a BMW dealer under the recall. Ask the dealer to check your VIN for open recalls.
Transmission control unit can leak and cut drive power (recall)
- What you'll notice
- Sudden loss of drive power or transmission warnings.
- Why it happens
- A weld on the cover of the automatic transmission's control unit can let transmission fluid inside, which could lock up the gears.
- What to do
- Have the dealer replace the mechatronic unit and fluid if needed under recall 23V-821.
Free at a BMW dealer under the recall. Ask the dealer to check your VIN for open recalls.
Cylinder head cover can crack and leak oil (recall)
- What you'll notice
- Oil smell or smoke from the engine bay, or oil drips under the front of the car.
- Why it happens
- The plastic cylinder head (valve) cover on some 2024 430i convertibles can crack, and oil reaching hot parts could catch fire.
- What to do
- Have the dealer inspect and replace the cover under recall 23V-863.
Free at a BMW dealer under the recall. Ask the dealer to check your VIN for open recalls.
Starter-generator battery cable can come loose (recall)
- What you'll notice
- The engine may stall, or there may be a burning smell from wiring.
- Why it happens
- The connection between the starter-generator and the battery on some 2025 430i models can loosen, which can stall the engine or overheat the wiring.
- What to do
- Have the dealer inspect and replace the starter-generator and battery cable as needed under recall 25V-202.
Free at a BMW dealer under the recall. Ask the dealer to check your VIN for open recalls.
Battery cable at the power distribution box may not connect (recall)
- What you'll notice
- The engine may stall, or there may be a burning smell or electrical warnings.
- Why it happens
- On some 2026 430i and M4 models, the positive battery cables may not be properly attached to the power distribution box, which can stall the engine or start a fire.
- What to do
- Have the dealer inspect and replace the cables and box under recall 25V-643.
Free at a BMW dealer under the recall. Ask the dealer to check your VIN for open recalls.
Valve cover gasket leaks oil or the plastic cover cracks
- What you'll notice
- Burning-oil smell, light smoke from around the engine, oil on the spark plugs, or a low-oil warning.
- Why it happens
- The valve cover gasket wears out, and the plastic valve cover itself can warp or crack. It is most common on the 2014-2016 engines but newer engines get it too.
- What to do
- Have the leak confirmed. Fix it before oil drips onto the hot exhaust or soaks the ignition parts.
Crankcase vent valve fails and the engine whistles
- What you'll notice
- A whistle, howl or squeal at idle, white exhaust smoke, rough running, or new oil leaks at the crankshaft seals.
- Why it happens
- The crankcase vent (PCV) valve is built into the valve cover, and its rubber diaphragm tears. Pressure then builds inside the engine and pushes oil past seals.
- What to do
- Have the vent valve tested. Dealers usually replace the whole valve cover; aftermarket repair kits also exist.
Oil filter housing gasket leaks oil
- What you'll notice
- Oil dripping at the front of the engine, oil on the drive belt, or a burning-oil smell.
- Why it happens
- The gasket under the oil filter housing hardens and leaks, and the plastic housing can crack. Leaks often show up around 50,000 miles.
- What to do
- Fix it soon. Oil on the drive belt can make it slip off and get pulled into the engine. Check the oil level often until it's repaired.
Plastic turbo charge pipe cracks and power drops
- What you'll notice
- A loud pop followed by a big loss of power, no boost, a check engine light or a Drivetrain Malfunction warning.
- Why it happens
- The plastic pipe carrying pressurized air from the turbo cracks or blows apart under boost. It happens sooner on tuned cars but also on stock ones.
- What to do
- The car can usually be driven gently to a shop. Many owners replace it with a stronger aluminum pipe.
Plastic coolant hoses and expansion tank crack and leak
- What you'll notice
- Low-coolant warning, a sweet smell, or coolant spots under the car.
- Why it happens
- Plastic cooling parts get brittle with age. The expansion tank hose is the most common failure, often between 50,000 and 90,000 miles.
- What to do
- Check the coolant level every few months. If the engine overheats, stop and have it towed.
VANOS solenoid fault causes rough running
- What you'll notice
- Check engine light, rough idle, hesitation, loss of power, a rattle, or limp mode.
- Why it happens
- A VANOS (variable valve timing) solenoid sticks or fails. On these newer engines the solenoids sit at the back of the engine, so they're harder to reach.
- What to do
- Have the codes read. Often only the solenoid needs replacing, and sometimes cleaning it fixes the problem.
Convertible driver airbag timing is set wrong (recall)
- What you'll notice
- None you can notice.
- Why it happens
- A programming error in the airbag control module of some early 2015 428i and 435i convertibles can deploy the driver's airbag at the wrong time.
- What to do
- Have the dealer reprogram the airbag module.
Free at a BMW dealer under the recall. Ask the dealer to check your VIN for open recalls.
Rearview camera image can go missing (recall)
- What you'll notice
- The backup camera screen stays dark or part of the picture is blocked when you shift into reverse.
- Why it happens
- Software in the rearview camera system can fail to show the full image.
- What to do
- Check behind the car directly until the dealer updates the software under recall 21V-096.
Free at a BMW dealer under the recall. Ask the dealer to check your VIN for open recalls.
M4 dual-clutch delays engaging Drive or Reverse
- What you'll notice
- After starting, the car hesitates or feels like it's in neutral when you shift from Park or Reverse into Drive, or into Reverse, even though the dash shows the gear.
- Why it happens
- This is a known behavior of the first M4's dual-clutch transmission, usually right after the car has been parked.
- What to do
- Wait a few seconds after starting before selecting a gear. A soft clunk into Reverse is normal. If it's getting worse or slipping, have a dealer check for software updates.
Repair prices for your BMW 4 Series
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace timing chain, guides and tensioner
- Replace electric water pump and thermostat
- Replace valve cover and gasket
- Replace valve cover with built-in vent valve
- Replace oil filter housing gasket
- Replace turbo charge pipe
- Replace coolant expansion tank and hose
- Replace VANOS solenoid
- Replace crank hub and reset timing
- Diagnose and update transmission software
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Dealer recall repairNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Pick a model year to see its safety recalls.