Your 1998 Chevrolet Blazerproblems, repair costs and recalls
What we've documented about the 1998 Chevrolet Blazer: problems owners and shops report, typical repair and upkeep costs, and safety recalls.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems for your 1998 Chevrolet Blazer
13 documented issues apply to 1998, most serious first.
S-10 Blazer: automatic transmission slips or loses gears
- What you'll notice
- Slipping, flaring RPM between shifts, harsh or late shifts, or suddenly no 2nd, 4th or reverse. The fluid may smell burnt.
- Why it happens
- The four-speed automatic (4L60-E) wears its 3-4 clutches, and an internal part called the sun shell can crack, taking out several gears. Owners report failures around 100,000 miles.
- What to do
- Check the fluid level and condition. If it slips or loses gears, avoid towing and get a transmission shop diagnosis; a rebuild with upgraded parts is the usual fix.
S-10 Blazer: intake manifold gasket leaks coolant
- What you'll notice
- Coolant level keeps dropping, the engine runs hot, the oil turns milky, or you smell coolant after driving.
- Why it happens
- The original intake manifold gaskets on the 4.3L V6 break down with heat and age and leak coolant outside or into the engine.
- What to do
- Watch the coolant level. If it keeps dropping or the oil looks milky, stop driving and have the gaskets replaced before the engine bearings are damaged.
S-10 Blazer: lower ball joints wear out
- What you'll notice
- Clunks over bumps, loose or wandering steering, or uneven front tire wear.
- Why it happens
- The front lower ball joints on this platform wear early, especially on 4WD models, and a badly worn joint can separate.
- What to do
- Have the ball joints checked for play at each tire rotation once past 50,000 miles, and replace them as soon as they're worn.
S-10 Blazer: rear brake pipe or control arm nuts (recalls)
- What you'll notice
- A brake fluid leak near the rear axle, a soft pedal, or clunking from the front suspension.
- Why it happens
- On some 1998 models a rear brake pipe could crack from fatigue, and on others the right lower control arm nuts were not tightened enough.
- What to do
- Check your VIN for open recalls and have the dealer inspect both items.
Free at a Chevrolet dealer if not already done. Ask the dealer to check your VIN for open recalls.
S-10 Blazer: central "spider" fuel injector sticks or leaks
- What you'll notice
- Rough running right after a cold start, long cranking, misfires and a check engine light, often worse after sitting overnight.
- Why it happens
- The 4.3L uses one central injector unit with small poppet valves feeding each cylinder. Deposits make them stick, and the unit can leak fuel into the intake.
- What to do
- Have misfire codes and fuel pressure checked. Replacing the central injector unit is the usual repair.
S-10 Blazer: fuel pump failure
- What you'll notice
- Cranks but won't start, stalls or sputters, or loses power going up hills.
- Why it happens
- The electric pump in the fuel tank wears out or develops an electrical fault. Owners of 2000 models report it around 85,000 miles.
- What to do
- Have fuel pressure tested. A failed pump means replacing the pump module inside the tank.
S-10 Blazer: gauges stop working
- What you'll notice
- The speedometer, fuel, temperature or tach gauges stop moving or drop to zero, sometimes along with the radio.
- Why it happens
- The gauge motors and solder joints inside the cluster fail, or loose connections cut power to it.
- What to do
- Have the cluster tested. Repair shops can rebuild it or replace the gauge motors.
S-10 Blazer: ABS light on from failed brake control module
- What you'll notice
- The ABS warning light stays on. Normal brakes work, but anti-lock braking is switched off.
- Why it happens
- The electronic brake control module on the ABS unit fails, or a wheel speed sensor goes bad.
- What to do
- Have the ABS codes read to find the faulty part. The brakes still stop the truck, but drive carefully on slick roads until it's fixed.
S-10 Blazer: misfire from distributor cap and rotor
- What you'll notice
- Misfires, rough idle, hard starting and a flashing or steady check engine light.
- Why it happens
- The plastic distributor cap on the 4.3L V6 sits in a hot spot, warps and wears the rotor.
- What to do
- Replace the cap, rotor and plug wires as a set; it's an inexpensive first fix for misfires.
S-10 Blazer: fuel gauge reads wrong
- What you'll notice
- The fuel gauge bounces, sticks at half, or shows fuel left when the tank is nearly empty.
- Why it happens
- The fuel level sender (a float on the pump module inside the tank) wears out.
- What to do
- Use the trip odometer to track fuel until it's fixed so you don't run dry. The fix is a new sender or pump module.
S-10 Blazer: blower works only on some speeds
- What you'll notice
- The heater and A/C fan works only on high, or quits on some speeds.
- Why it happens
- The blower motor resistor burns out. A worn blower motor can overload it.
- What to do
- Replace the resistor. If the fan motor is noisy or slow, replace it too.
S-10 Blazer: doors sag from worn hinge pins
- What you'll notice
- Doors drop when opened and must be lifted to close, or they creak and pop.
- Why it happens
- The hinge pins and bushings wear out, especially on the heavy front doors.
- What to do
- Install a hinge pin and bushing kit before the worn hinge damages the door or striker.
S-10 Blazer: oil pressure gauge drops or jumps
- What you'll notice
- The oil pressure gauge falls to zero or swings while the engine sounds normal.
- Why it happens
- The oil pressure sender on the 4.3L V6 often fails. Real low pressure must still be ruled out.
- What to do
- Check the oil level, then have pressure checked with a mechanical gauge. If pressure is good, a new sender fixes it.
Repair prices for your 1998 Chevrolet Blazer
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Rebuild or replace 4L60-E automatic transmission
- Replace intake manifold gaskets and coolant
- Replace central (spider) fuel injector assembly
- Replace in-tank fuel pump module
- Replace fuel level sender or pump module
- Rebuild instrument cluster or replace gauge motors
- Replace ABS electronic brake control module
- Replace blower motor resistor (and motor if worn)
- Replace door hinge pins and bushings (one door)
- Replace oil pressure sender
- Replace distributor cap, rotor and spark plug wires
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Free dealer recall repairNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Checking the NHTSA recall database…