Chevrolet Malibuproblems, repair costs and recalls
Problems reported across 1997–2025. Pick your model year below to see what applies to your vehicle.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems
34 documented issues across all years, most serious first.
Intake manifold gasket coolant leak
- What you'll notice
- Coolant level keeps dropping, a sweet smell after driving, coolant around the top or front of the engine, rising temperature gauge, or milky oil on the dipstick.
- Why it happens
- The lower intake manifold gaskets on this V6 break down with age and heat and let coolant leak outside the engine or into the oil.
- What to do
- Get it repaired soon instead of topping off and driving. Coolant mixing into the oil can wipe out the bearings, and overheating can warp the heads.
Ignition can be bumped out of Run (recall 14V-400)
- What you'll notice
- The engine suddenly shuts off while driving, often after the key or a heavy key ring gets bumped, and power steering and brake assist feel heavy.
- Why it happens
- A heavy key ring or a knee bump can move the ignition key out of the Run position, which cuts the engine and can keep the airbags from deploying in a crash.
- What to do
- Use only the ignition key on a light ring until the recall work is done. Check your VIN for open recall 14V-400 and get the free repair.
Steering rack bearing retainer can fail (recall 03V-527)
- What you'll notice
- Clunking from the steering, play or looseness in the wheel, or steering that does not respond the way it should.
- Why it happens
- Retainer tabs that hold the pinion bearing inside the steering rack can break, which can affect steering control.
- What to do
- Do not keep driving with loose or clunking steering. Check your VIN for recall 03V-527 and have the rack inspected.
Accelerator pedal can stick in heat (recall 04V-528)
- What you'll notice
- In hot weather the gas pedal is slow to come back up, so the engine keeps revving or the car does not slow down when you lift off.
- Why it happens
- The accelerator pedal arm can bind in high temperatures and not return to idle.
- What to do
- If the pedal sticks, shift to Neutral and brake firmly. Check your VIN for recall 04V-528 before driving the car normally again.
Electric power steering assist cuts out (recalls 14V-153 and 15V-064)
- What you'll notice
- The steering suddenly gets very heavy, often with a power steering warning message. It may come and go.
- Why it happens
- The electric assist motor and its control parts in the steering column can fail, so you lose power assist. GM recalled these years and replaced the motor, column or control unit as needed.
- What to do
- Grip the wheel firmly and pull over safely when it happens. Check your VIN for recalls 14V-153 and 15V-064 and get the free repair.
Shift cable can break or come loose (recalls)
- What you'll notice
- The gear shown on the shifter does not match the gear the car is actually in, or the car can roll after you put it in Park.
- Why it happens
- The shift cable, its end tabs, or its retaining clip can crack or come off, so the transmission is not in the gear you selected. GM ran several recalls on these years.
- What to do
- Always set the parking brake when you park. Check your VIN for recalls 14V-224, 12V-460 and 09V-073 and have the cable repaired.
Brake lights and stability control fault from body module connector (recall 14V-252)
- What you'll notice
- Brake lights stay off when braking or stay on when you are not braking, a stability control or traction warning appears, or cruise control will not engage.
- Why it happens
- Corrosion and wear at a body control module connector raise electrical resistance, which can disrupt brake light and stability control signals.
- What to do
- A car with no brake lights can be rear-ended, so get it checked right away. Check your VIN for recall 14V-252 and get the free repair.
6-speed automatic loses 3rd, 5th and Reverse
- What you'll notice
- No reverse, the transmission skips or drops gears, harsh shifting, a flashing gear indicator, or a check engine light.
- Why it happens
- A wave plate inside the 6-speed automatic can crack and break up, which takes out the clutch for 3rd, 5th and Reverse and sends debris through the unit. GM offered extended coverage on 2008-2009 models under bulletin 14404, which has since run out.
- What to do
- Stop driving if the car has no reverse or is slipping badly, and have a transmission shop diagnose it. Repairing it early can keep debris from ruining the rest of the transmission.
Oil burning and timing chain stretch
- What you'll notice
- Needing to add oil between changes, a rattle at startup, rough idle or misfires, and a check engine light with cam or crank timing codes.
- Why it happens
- Piston ring problems on this engine let it burn oil, and when the oil runs low the timing chain, guides and tensioner wear quickly. GM issued an oil consumption diagnostic bulletin for these cars.
- What to do
- Check the oil every fill-up and never let it run low. Have a startup rattle or timing code checked quickly, because a chain that jumps can badly damage this engine.
Driver airbag inflator can rupture (recall 19V-019)
- What you'll notice
- There is usually no warning sign before a crash.
- Why it happens
- The driver frontal airbag inflator can build too much pressure and burst when it deploys, throwing metal pieces into the cabin.
- What to do
- Check your VIN for recall 19V-019 right away and get the free repair as soon as possible.
Rear toe links can corrode and break (recalls 20V-764, 21V-633)
- What you'll notice
- Clunking from the rear, the car pulling or feeling loose at the back, or uneven rear tire wear.
- Why it happens
- Extra coating on the rear toe links can trap moisture, letting them corrode and possibly fracture, which affects how the car tracks.
- What to do
- Do not ignore rear clunks or a wandering feel. Check your VIN for these recalls and get the free repair.
Key can come out when not in Park (recall 16V-502)
- What you'll notice
- You can remove the key even though the shifter is not fully in Park, and the car may roll away after you walk off.
- Why it happens
- A fault in the shifter and key interlock lets the key come out without the transmission being locked in Park.
- What to do
- Always confirm Park and set the parking brake. Check your VIN for recall 16V-502 and get the free repair.
Brake assist loss with auto stop/start (recall 14V-247)
- What you'll notice
- The brake pedal feels hard and needs much more effort to stop the car, especially after the engine restarts from an auto stop.
- Why it happens
- On the 2.5L with stop/start, the brake vacuum assist can be lost, so stopping distances get longer.
- What to do
- Press the brake harder if needed and get it fixed right away. Check your VIN for recall 14V-247.
Shift cable adjuster can disengage (recall 14V-092)
- What you'll notice
- The shifter does not match the gear the car is in, or the car is not truly in Park when the shifter says it is.
- Why it happens
- The shift cable adjuster can come apart from the shift lever, so the car may roll after being parked.
- What to do
- Use the parking brake every time you park and check your VIN for recall 14V-092.
ABS and stability control can shut off (recall 16V-272)
- What you'll notice
- ABS and stability control warning lights come on, and anti-lock braking may not work.
- Why it happens
- A memory chip in the brake control module can fail, disabling anti-lock brakes and stability control.
- What to do
- Drive gently and leave extra stopping distance. Check your VIN for recall 16V-272 and get it fixed promptly.
High-pressure fuel pump can come loose (recall 18V-358)
- What you'll notice
- A fuel smell under the hood, a fuel leak, or the engine stalling.
- Why it happens
- The engine-mounted high-pressure fuel pump can detach and damage the fuel line, which can leak fuel near hot parts.
- What to do
- If you smell fuel, stop driving and have the car towed. Check your VIN for recall 18V-358.
Passenger airbag sensor may be miscalibrated (recall 18V-400)
- What you'll notice
- The passenger airbag status light shows the wrong state for who is in the seat, or an airbag warning light comes on.
- Why it happens
- The front passenger presence sensor can be miscalibrated, so the passenger airbag may turn off when it should be on.
- What to do
- Check your VIN for recall 18V-400 and get the free repair. Keep children in the back seat.
Software can shut off fuel injectors (recall 19V-642)
- What you'll notice
- The engine suddenly loses power or stalls while driving.
- Why it happens
- An error in the engine control software can disable the fuel injectors, cutting engine power.
- What to do
- Check your VIN for recall 19V-642 and get the software update right away.
Transmission fluid leak from stop/start accumulator (recall 20V-668)
- What you'll notice
- Transmission fluid under the car, a burning smell, or the car will not move after an auto-stop.
- Why it happens
- Bolts may be missing from the stop/start accumulator end cap, which can let fluid leak and cause a loss of drive or a fire risk.
- What to do
- Stop driving if fluid is leaking or the car will not move. Check your VIN for recall 20V-668.
Side airbag inflator can rupture (recall 15V-666)
- What you'll notice
- No warning in normal driving; it shows up only if the side airbag deploys.
- Why it happens
- The side impact airbag inflator can burst when it fires and send pieces toward the people inside.
- What to do
- Have this campaign done as soon as you can, because the airbag meant to protect you can injure you instead.
CVT slips or loses drive (code P2714)
- What you'll notice
- The car slips or hesitates under power, sometimes refuses to pull away for several seconds, and the check engine light can come on. Some cars lose forward drive altogether.
- Why it happens
- A regulator valve inside the CVT valve body sticks, and once line pressure drops the forward clutch piston or the pulley bearing bore can be damaged too.
- What to do
- Get it diagnosed before you drive it much further. Caught early this can be a valve body, but a burnt clutch or a worn pump means a rebuilt or replacement transmission.
Passlock anti-theft no-start
- What you'll notice
- The engine cranks but will not start, or starts and dies right away, and the security light is on or flashing. It may start after sitting a while.
- Why it happens
- The Passlock sensor in the ignition lock housing can fail, so the computer thinks the car is being stolen and shuts off fuel.
- What to do
- Leaving the key in On for about ten minutes may let the system relearn and get you home. A shop can test the sensor and ignition cylinder for a lasting fix.
Low-beam headlights stop working
- What you'll notice
- One or both low beams go out even with good bulbs, sometimes with a blown low-beam fuse.
- Why it happens
- Shorts and corroded contacts in the headlight wiring harness can blow the fuse or cut power to the lamps.
- What to do
- Have the wiring and fuse checked rather than just replacing bulbs. Use high beams carefully until it is fixed, since driving at night without low beams is unsafe.
Front seat belt anchor cable can break (recall 15V-269)
- What you'll notice
- The seat belt anchor next to the seat looks frayed or separated, or the belt feels loose at the buckle side.
- Why it happens
- Repeated bending as people get in and out can fatigue the steel cable that anchors the outboard belt, so it may not hold in a crash.
- What to do
- Check your VIN for recall 15V-269 and get the free repair.
Water pump leak or failure
- What you'll notice
- Coolant leaking near the belt side of the engine, a low coolant warning, a sweet smell, noise from the pump at startup, or the temperature gauge climbing.
- Why it happens
- The water pump on these engines can start leaking or wear out early. GM asked dealers for field information on noisy water pumps in an engineering bulletin.
- What to do
- Watch the temperature gauge and pull over if it heads toward hot. Have a leak or noisy pump replaced before it causes overheating.
Engine Power Reduced and loss of power
- What you'll notice
- An Engine Power Reduced message, check engine light, sudden loss of acceleration, hesitation, or stalling while driving.
- Why it happens
- Owners report faults in the electronic throttle and accelerator pedal sensor circuits that put the engine into a reduced-power mode. Many complaints for these years describe this.
- What to do
- Get to a safe spot if power drops. Have the stored codes read and ask the dealer about updated software and related bulletins.
Power loss and stalling in extreme cold (TSB 18-NA-069)
- What you'll notice
- In very cold weather the car hesitates, loses power, may stall, and the check engine light comes on with boost codes.
- Why it happens
- Moisture in the turbo charge air cooler can freeze and block airflow, and contamination can freeze in the wastegate control valve. GM issued a redesigned cooler, a software update and, on some years, a winter grille cover.
- What to do
- Ask a dealer about bulletin 18-NA-069. After it warms up the car usually runs again, but get it checked before the next cold snap.
"Shift to Park" message will not clear
- What you'll notice
- After putting it in Park and shutting off, the car keeps saying Shift to Park and will not fully power down, which can drain the battery.
- Why it happens
- A poor electrical connection between the shifter Park switch and the body control module. GM issued a bulletin that adds a wiring jumper and, if needed, replaces the shifter.
- What to do
- Wiggling the shifter in Park may clear it for now. Ask a dealer about the Shift to Park bulletin for a permanent repair.
Rear seat belt retractor fasteners loose (recall 21V-649)
- What you'll notice
- A rattle from a rear seat belt retractor, or a rear belt that does not lock up properly.
- Why it happens
- Fasteners holding the rear seat belt retractors may be loose or missing, so the belt may not restrain a passenger in a crash.
- What to do
- Check your VIN for recall 21V-649 and get the free repair.
Driver seat tilt weld may be weak (recall 22V-359)
- What you'll notice
- The driver seat feels loose or moves when it should not.
- Why it happens
- A weld in the driver seat cushion frame tilt mechanism may be weak, so the seat may not hold properly in a crash.
- What to do
- Check your VIN for recall 22V-359 and get the free repair.
Front impact bar weld may be incomplete (recall 22V-923)
- What you'll notice
- There is usually no sign while driving.
- Why it happens
- The front impact bar may not be fully welded to the frame rail, which reduces crash protection.
- What to do
- Check your VIN for recall 22V-923 and get the free repair.
Rearview camera picture distorted or blank (recall 26V-212)
- What you'll notice
- The backup camera shows a distorted, frozen or blank image when you shift into Reverse.
- Why it happens
- A fault can keep the rearview camera image from displaying correctly.
- What to do
- Look carefully behind you when backing up and check your VIN for recall 26V-212.
Sunroof can close by itself when the switch is brushed (recall 15V-164)
- What you'll notice
- The sunroof panel starts closing on its own after something touches the roof switch.
- Why it happens
- The slide and tilt switch sits where it can be pressed by accident, and the roof then runs its auto-close.
- What to do
- Have the switch updated under the campaign and keep hands and heads clear of the opening until it is done.
Turbo wastegate rattle (PIP5418A)
- What you'll notice
- A rattle from the turbocharger area, usually at idle or light throttle.
- Why it happens
- GM issued a bulletin to help technicians trace a rattle to the turbocharger wastegate actuator rod.
- What to do
- Mention bulletin PIP5418A to the dealer if you hear a rattle from the turbo area. It is a noise concern, but have it confirmed.
Repair prices for your Chevrolet Malibu
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace lower intake manifold gaskets and refill coolant
- Install ignition key insert or key cover (recall)
- Install new steering gear lower pinion bearing
- Replace ignition lock cylinder and Passlock sensor
- Replace accelerator and brake pedal assembly
- Replace power steering motor, torque sensor or controller
- Replace shift cable and bracket
- Secure body module connector and relearn brake pedal position
- Replace 3-5-Reverse wave plate (transmission overhaul)
- Replace timing chain, guides and tensioner (2.4L)
- Repair burnt headlight connector and wiring
- Replace driver front airbag module
- Replace front seat belt anchor bracket and cable
- Replace water pump and refill coolant (2.5L)
- Replace rear toe links and adjuster bolts
- Replace ignition key cylinder lock housing
- Update brake control module software (recall)
- Inspect and replace shift cable adjuster
- Replace electronic throttle body
- Replace charge air cooler with updated part, clean turbo control valve, reprogram engine computer
- Install anti-rattle spring on wastegate actuator rod
- Replace electronic brake control module
- Replace high-pressure fuel pump and fuel pipe
- Install passenger seat sensor service kit
- Inspect and tighten rear seat belt retractors
- Reprogram engine control module (recall)
- Inspect and replace transmission start/stop accumulator
- Replace driver seat cushion frame
- Inspect and replace rearview camera
- Replace side impact airbag module
- Replace sunroof slide and tilt switch
- Replace CVT valve body, or rebuild/replace the transmission
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Free dealer recall repairNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Pick a model year to see its safety recalls.