Chevrolet Suburbanproblems, repair costs and recalls
Problems reported across 1996–2027. Pick your model year below to see what applies to your vehicle.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems
50 documented issues across all years, most serious first.
Throttle cable can catch on the dash mat (recall)
- What you'll notice
- The gas pedal sticks or the engine does not drop back to idle when you lift off.
- Why it happens
- An accessory dash mat could rub against the throttle cable and keep it from returning.
- What to do
- If the throttle sticks, shift to neutral and stop safely. Have a dealer confirm recall 96V-057 was done.
Power mirror switch can short and overheat (recall)
- What you'll notice
- A hot plastic or burning smell near the driver's door, or a mirror switch that stops working.
- Why it happens
- The power mirror switch could short internally and overheat, with a risk of fire.
- What to do
- Have a dealer confirm recall 03V-093 was done. Get any burning smell checked right away.
Front brake rotors can crack (recall)
- What you'll notice
- Grinding, clunking, or vibration from a front wheel when braking.
- Why it happens
- Some front rotors were cast from out-of-spec iron and could crack, in the worst case letting the wheel come loose.
- What to do
- Stop driving if you hear new noises from a front wheel and have recall 98V-033 checked.
4L60-E automatic slipping or failing
- What you'll notice
- Engine revs flare between shifts, missing gears (often third or fourth), slow or no reverse, or dark burnt-smelling fluid.
- Why it happens
- Heat and heavy loads wear out the clutches and internal parts of this four-speed automatic, commonly around the 80,000 to 100,000 mile mark.
- What to do
- Avoid towing until it is checked. A transmission shop can confirm whether it needs a rebuild.
Rusted brake lines
- What you'll notice
- A soft or sinking brake pedal, a brake warning light, or wet spots near the wheels or along the frame.
- Why it happens
- Steel brake lines running along the frame rust through in road-salt areas and can burst.
- What to do
- If the pedal goes soft, stop driving and have the truck towed. Ask your shop to look at the lines every oil change if you live where roads are salted.
Fuel pump wiring connector overheats (recall)
- What you'll notice
- Stalling, a no-start, or a fuel smell near the tank.
- Why it happens
- The electrical connector for the fuel pump could overheat, causing stalls or fuel leaks.
- What to do
- Have a dealer confirm recall 05V-155 was completed. Treat a fuel smell as urgent.
Exhaust fumes can enter the cabin (recall)
- What you'll notice
- An exhaust smell inside, especially with the windows closed or when stopped.
- Why it happens
- Plugs in the rear wheelhouse could be loose or missing, letting exhaust gases into the cabin.
- What to do
- Drive with windows open and have recall 00V-343 checked right away. Exhaust fumes can cause carbon monoxide poisoning.
Power steering pump shaft can break (recall)
- What you'll notice
- Steering suddenly becomes very heavy.
- Why it happens
- The shaft that drives the hydraulic pump could fracture and cut off power steering assist.
- What to do
- Have a dealer confirm recall 05V-005 was done. If steering turns heavy, slow down and stop safely.
Running board light wiring can overheat (recall)
- What you'll notice
- A burning plastic smell, melted running boards, or courtesy lights that flicker or stop working.
- Why it happens
- Wiring for the lights in the running boards could overheat and melt nearby plastic, with a risk of fire.
- What to do
- Have a dealer confirm recall 03V-094 was completed.
ABS kicks in at low speed
- What you'll notice
- The pedal pulses and the truck feels like it won't stop when braking gently at low speed, sometimes with the ABS light on.
- Why it happens
- Rust buildup on the front wheel speed sensors makes the ABS think a wheel is locking. A recall covered 2000-2002 trucks in salt states.
- What to do
- Have the wheel speed sensors and ABS module checked, and ask a dealer about recall 05V-379.
Hydraulic brake booster problems (recall)
- What you'll notice
- A hard brake pedal that takes much more effort to stop the truck.
- Why it happens
- On trucks with hydraulic (hydro-boost) brake assist, a relief valve seal could break or the booster's accumulator could crack.
- What to do
- Have a dealer confirm recalls 04V-045 and 05V-043 were done. Stop driving if the pedal turns hard.
Fuel rail parts can crack and leak (recall)
- What you'll notice
- A gasoline smell under the hood or fuel dripping near the engine.
- Why it happens
- A clip on the fuel rail damper or screws on the fuel rail crossover could break, letting fuel leak onto a hot engine.
- What to do
- Do not drive with a fuel smell. Have a dealer check recalls 06V-289 and 04V-376.
Heated washer fluid system fire risk (recall)
- What you'll notice
- A burning smell or smoke from under the hood, or washer heating that stops working.
- Why it happens
- The heated washer module could short and overheat. GM first added a fused harness, then disabled and removed the module.
- What to do
- Have a dealer confirm recalls 08V-441 and 10V-240 were completed.
Collapsed cylinder deactivation lifter
- What you'll notice
- Ticking or tapping from the engine, a check engine light with misfire codes, rough running, or lost power.
- Why it happens
- The special lifters that let the engine shut off cylinders can stick or collapse, and may wear the camshaft.
- What to do
- Have it diagnosed soon. Do not keep driving with a steady misfire and ticking.
Water can damage the fuel pump control module (recall)
- What you'll notice
- Engine stalling, a no-start, or warning lights, often after rain or a car wash.
- Why it happens
- Water could get into the fuel system control module and cause it to malfunction.
- What to do
- Have a dealer confirm recall 09V-154 was completed.
Steering gear shaft can fracture (recall)
- What you'll notice
- Loose, clunky steering, or a sudden loss of steering control.
- Why it happens
- The pitman shaft in the steering gear could crack.
- What to do
- Do not drive if the steering feels loose. Have recall 12V-112 checked right away.
Shifter can leave Park without the brake (recall)
- What you'll notice
- The shifter moves out of Park without pressing the brake, or with the key out.
- Why it happens
- A fault in the steering column shift interlock could let the transmission leave Park, so the truck could roll away.
- What to do
- Always set the parking brake and have a dealer confirm recall 13V-001 was completed.
Body control module can short and stall the engine (recall)
- What you'll notice
- Warning lights, electrical glitches, or the engine stalling while driving.
- Why it happens
- Contamination inside a chassis electrical module could cause a short.
- What to do
- Have a dealer confirm recall 14V-614 was done. A stall in traffic is dangerous.
Rear brake caliper bolts may be loose (recall)
- What you'll notice
- Clunking or knocking from the rear wheels when braking, or weaker braking.
- Why it happens
- The bolts holding the rear calipers might not have been tightened properly at the factory.
- What to do
- Have a dealer confirm recall 13V-342 was completed before regular driving.
Hard brake pedal from vacuum pump problems (recall)
- What you'll notice
- A stiff brake pedal and longer stops, often at low speed, sometimes with a brake warning.
- Why it happens
- The engine-driven vacuum pump that powers the brake booster can lose output, cutting brake assist.
- What to do
- If the pedal turns hard, press firmly and get off the road safely. Have a dealer confirm recall 19V-645 was done.
Electric power steering can cut out (recall)
- What you'll notice
- Steering suddenly turns heavy, sometimes with a message on the dash, then may come back.
- Why it happens
- A fault in the electric steering assist motor or its software could drop power assist.
- What to do
- Have a dealer confirm recalls 14V-719 and 18V-586 were completed.
Transmission cooler line can leak (recall)
- What you'll notice
- Red fluid under the truck, a burning smell, or smoke from under the hood.
- Why it happens
- A transmission cooler line might not have been fully seated, letting fluid leak onto hot parts.
- What to do
- Stop driving if you see smoke or smell burning fluid. Have recall 14V-152 checked.
Unexpected braking on one side (recall)
- What you'll notice
- The truck pulls or brakes on one side without you pressing the pedal, usually at low speed.
- Why it happens
- A faulty wheel speed sensor signal could make the stability system apply a brake on its own.
- What to do
- Have a dealer confirm the software update for recall 19V-761 was done.
Air bags may not deploy during a self-test (recall)
- What you'll notice
- Usually none. In rare cases the air bag light may come on.
- Why it happens
- Software could start a self-test while driving, and if a crash happened during it, the air bags and belt pretensioners might not deploy.
- What to do
- Have a dealer confirm recall 16V-651 was done.
Front control arm welds may fail (do-not-drive recall)
- What you'll notice
- Clunking from the front suspension, wandering, or a wheel that sits at an odd angle.
- Why it happens
- Poor welds on the front lower control arm could let it separate, causing loss of control.
- What to do
- Do not drive until a dealer confirms recall 16V-256 was done.
Transfer case missing a part (do-not-drive recall)
- What you'll notice
- Clunking or grinding from under the truck, or sudden wheel lockup, on certain 2015 and 2017-2020 four-wheel-drive models.
- Why it happens
- A part could be missing from a replacement transfer case, which can lock the front or rear wheels.
- What to do
- Do not drive until a dealer checks your VIN for recall 26V-289.
Free under GM recall. Check your VIN first or ask a Chevrolet dealer. Do not drive it until the check is done.
Fuel pump missing pressure regulator (recall)
- What you'll notice
- A fuel smell, a fuel leak, or rough running.
- Why it happens
- Some fuel pumps were built without a pressure regulator, which can over-pressurize the fuel system and cause leaks.
- What to do
- Do not drive with a fuel smell. Have recall 19V-837 checked.
Power steering assist can drop out (recall)
- What you'll notice
- Steering suddenly turns heavy, often with a warning message.
- Why it happens
- A software problem could switch off the electric power steering assist.
- What to do
- Have a dealer apply the update for recall 21V-455.
Fuel pump control module can cause stalling (recall)
- What you'll notice
- The engine stumbles, loses power, or stalls while driving.
- Why it happens
- The fuel pump control module could interrupt fuel delivery.
- What to do
- Have a dealer confirm recall 21V-739 was completed.
Rear driveshaft may break (recall)
- What you'll notice
- Vibration, clunking or banging from under the truck, or sudden loss of drive.
- Why it happens
- Some rear driveshaft parts were not properly heat-treated and could fail.
- What to do
- Have a dealer confirm recall 22V-036 was done. Stop driving if you feel new vibration from underneath.
Rear wheels can lock up (recall)
- What you'll notice
- Sudden harsh downshift or rear wheel lockup while driving, sometimes with a transmission warning.
- Why it happens
- A valve in the automatic transmission's control system could fail and lock the rear wheels. GM is updating transmission software.
- What to do
- Have a dealer apply recalls 24V-797 or 26V-085 as they apply to your VIN. Until then, drive cautiously and leave extra following room.
Free under GM recall. Check your VIN first.
6.2L V8 rod or crankshaft failure (recall)
- What you'll notice
- Knocking from the engine, rough running, a check engine light, or sudden loss of power.
- Why it happens
- Manufacturing defects in the connecting rods or crankshaft can lead to sudden engine failure.
- What to do
- Stop driving if the engine knocks. Have a dealer check your VIN for recall 25V-274.
Rear control arm bolts can break (recall)
- What you'll notice
- Clunking from the rear, the truck wandering, or a change in how it tracks.
- Why it happens
- Bolts holding the rear outer control arms could break.
- What to do
- Have a dealer confirm recall 23V-642 was done. Stop driving if the rear feels loose.
Wrong front hub bolts can work loose (recall)
- What you'll notice
- Clicking or clunking from a front wheel, a wobble or vibration that gets worse with speed, or a wheel that feels loose.
- Why it happens
- Trucks built with the largest wheels got incorrect bolts on the left and right front wheel hubs, and those bolts can loosen or deform.
- What to do
- Run your VIN for this recall and have the hub bolts replaced. If a front wheel is making new noises or feels loose, stop driving it.
Transfer case may be missing a part and lock the wheels (do-not-drive recall)
- What you'll notice
- Usually no warning at all; the front or rear wheels can suddenly lock while you are driving.
- Why it happens
- A component was left out of some four-wheel-drive and all-wheel-drive transfer cases, which lets the unit seize.
- What to do
- Do not drive it. Check the VIN and arrange a tow to the dealer for the free repair.
Windshield wipers work on and off (recall)
- What you'll notice
- The wipers stop, start on their own, or ignore the switch, often in rain when you need them.
- Why it happens
- Solder joints on the wiper motor circuit board can crack.
- What to do
- Have a dealer check recalls 98V-150 and 03V-159. Avoid driving in heavy rain until it is fixed.
"Spider" fuel injector unit clogs or leaks
- What you'll notice
- Hard starting, misfires, rough idle, a check engine light, or a raw fuel smell under the hood.
- Why it happens
- This engine uses one central injector with thin lines and small poppet nozzles feeding each cylinder. The nozzles stick or clog and the lines can leak with age.
- What to do
- Have fuel pressure and misfires checked. Treat a fuel smell as urgent because of the fire risk. An updated injector assembly is the usual fix.
Intake manifold gasket coolant leak
- What you'll notice
- Coolant level drops with no obvious leak, coolant crust around the intake, a sweet smell, or milky oil.
- Why it happens
- The intake gaskets break down and let coolant seep out or into the oil.
- What to do
- Have it pressure-tested soon. If coolant is getting into the oil, stop driving until it is fixed to protect the engine bearings.
Fuel pump failure
- What you'll notice
- Long cranking before starting, sputtering or stalling under load, or a no-start.
- Why it happens
- The in-tank electric fuel pump wears out, often somewhere around 80,000 to 100,000 miles.
- What to do
- Have fuel pressure tested. Do not keep driving with stalling, since it can leave you stranded in traffic.
Crankshaft position sensor failure (recall)
- What you'll notice
- The engine stalls, cuts out, or cranks but will not start, sometimes only now and then.
- Why it happens
- The crankshaft position sensor could fail intermittently or completely.
- What to do
- Have a dealer check recall 07V-521.
V8 burns oil
- What you'll notice
- Oil level drops between changes, low oil pressure or low oil warnings, blue smoke at startup, or fouled plugs and misfires.
- Why it happens
- Oil gets past the piston rings and burns. The cylinder deactivation system is widely linked to it.
- What to do
- Check the oil often and never let it run low. Ask a dealer for an oil consumption test and any applicable bulletins.
Ignition key can stick in Start (recall)
- What you'll notice
- The key stays in the start position after the engine is running, or turns roughly.
- Why it happens
- The ignition lock cylinder could bind. If the key is left in a bad position, power to systems like the air bags may be affected.
- What to do
- Have a dealer confirm recall 14V-827 was done.
Harsh or jerky automatic shifting
- What you'll notice
- Jerky or delayed shifts, a clunk when going into gear, shudder, or loss of power while driving.
- Why it happens
- Owners report shifting problems and some outright failures on the automatic in this generation.
- What to do
- Have the fluid and transmission software checked and ask the dealer about any bulletins. Get slipping or loss of drive looked at right away.
Rear seat belts may not lock for child seats (recall)
- What you'll notice
- A belt-installed child seat stays loose because the belt will not lock.
- Why it happens
- The rear belt retractors could fail to switch into their child-seat locking mode.
- What to do
- Use the LATCH anchors and have recall 18V-673 checked.
Third-row seat belts can be damaged (recall)
- What you'll notice
- A third-row belt is trapped, frayed, or a buckle feels loose.
- Why it happens
- Belts could get caught behind the seat mechanism, and some buckles had a poorly formed rivet.
- What to do
- Inspect the third-row belts and have a dealer check recalls 21V-190 and 22V-617.
Clunk from the steering intermediate shaft
- What you'll notice
- A clunk or knock felt in the steering wheel when turning at low speed or over bumps, often coming back after repair.
- Why it happens
- The sliding steering shaft between the column and the steering gear loses its lubrication and binds.
- What to do
- A shop can lubricate or replace the shaft as described in GM bulletins. It is annoying more than dangerous, but have loose steering checked.
Instrument cluster gauges stick or quit
- What you'll notice
- The speedometer, fuel or temperature needles freeze, drop to zero, or read wrong, and warning lights may flicker.
- Why it happens
- The small motors that move each needle fail with age. GM extended coverage on many of these clusters.
- What to do
- A cluster repair or replacement fixes it. Ask a dealer whether special coverage 07187A applies.
Cracked dashboard
- What you'll notice
- Cracks in the top of the dash, often near the passenger air bag.
- Why it happens
- The dash top shrinks and cracks after years of sun and heat.
- What to do
- Mostly cosmetic. A dash cover helps, but have a cracked air bag cover inspected.
A/C stops cooling from a condenser leak
- What you'll notice
- The A/C gradually blows warmer, and oily residue may show at the front of the radiator area.
- Why it happens
- The A/C condenser and its lines can crack and leak refrigerant. GM extended coverage for some owners.
- What to do
- Have the A/C leak-tested and ask a dealer whether extended coverage applies to your VIN.
Daytime running lights stay on with headlights (recall)
- What you'll notice
- Daytime running lights stay bright at night along with the headlights, which can add glare.
- Why it happens
- A software setting kept the daytime lights on when the headlights were on.
- What to do
- Have a dealer apply the software fix for recalls 22V-827 and 22V-903.
Repair prices for your Chevrolet Suburban
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace windshield wiper motor
- Repair power mirror switch circuit (recall remedy)
- Replace front brake rotor and hub assembly
- Replace central (spider) fuel injector assembly
- Replace lower intake manifold gaskets and coolant
- Replace with remanufactured 4L60-E transmission
- Replace rusted brake lines (full preformed line set)
- Replace fuel pump module
- Repair fuel pump wiring and connector
- Install missing body and wheelhouse plugs
- Repair running board light wiring (recall remedy)
- Replace crankshaft position sensor
- Replace intermediate steering shaft
- Diagnose ABS and clean or replace front wheel speed sensor
- Rebuild instrument cluster (replace gauge stepper motors)
- Replace hydraulic brake booster
- Replace fuel rail damper clip or fuel rail
- Disable or replace heated washer module (recall remedy)
- Replace pistons and rings (GM oil consumption fix)
- Replace valve lifters and camshaft
- Replace upper dash pad
- Replace ignition lock actuator and key (recall remedy)
- Inspect and replace steering gear
- Repair steering column shift lock (recall remedy)
- Replace body control module (recall remedy)
- Inspect and tighten rear brake caliper bolts
- Replace brake vacuum pump
- Replace A/C condenser and recharge system
- Power steering repair or software update (recall remedy)
- Reseat or replace transmission cooler line fitting
- Update brake control software (recall remedy)
- Update air bag module software (recall remedy)
- Replace front upper control arms
- Inspect and replace rear seat belt retractors
- Update power steering software (recall remedy)
- Replace fuel pump power control module
- Replace rear driveshaft assemblies
- Inspect and replace third-row seat belt buckles
- Update body control module software (recall remedy)
- Replace engine assembly
- Replace rear suspension control arm bolts
- Replace front wheel hub bolts, both sides
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Inspect and replace transfer case if needed (recall remedy)No charge if your vehicle is included
- Reprogram transmission control software (recall remedy)No charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Pick a model year to see its safety recalls.