Chevrolet Tahoeproblems, repair costs and recalls
Problems reported across 1996–2027. Pick your model year below to see what applies to your vehicle.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems
42 documented issues across all years, most serious first.
Throttle may not return to idle (recall)
- What you'll notice
- The engine stays at higher revs after you lift off the gas pedal.
- Why it happens
- The throttle cable could rub on the dash mat and bind.
- What to do
- Check that this recall was done. If the throttle sticks, shift to neutral, stop safely and have it towed.
Front rotor and hub can crack (recall)
- What you'll notice
- A grinding or clunking noise from a front wheel, vibration, or a wheel that feels loose.
- Why it happens
- Some front rotor and hub castings were made from out-of-spec iron and could crack, which could lead to the wheel coming off.
- What to do
- Check your VIN for this recall. If you hear new noises from a front wheel, stop driving and have it inspected.
Lower steering shaft bolt may be loose (recall)
- What you'll notice
- Looseness or clunking in the steering, or steering that stops responding.
- Why it happens
- A pinch bolt on the lower steering shaft could be loose or missing, letting the shaft separate from the steering gear.
- What to do
- Check your VIN for this recall. Any sudden looseness in the steering means stop driving and have it towed.
Exhaust fumes can get into the cabin (recall)
- What you'll notice
- An exhaust smell inside the vehicle, especially with windows closed.
- Why it happens
- Rear wheelhouse plugs could be loose or missing, letting exhaust gases into the passenger area.
- What to do
- Do not drive with an exhaust smell inside. Check your VIN for this recall and have the plugs fixed.
Heated washer fluid module can overheat (recall)
- What you'll notice
- Smoke or a burning smell from under the hood, or the washers stop working.
- Why it happens
- The heated windshield washer module could short and overheat, with a risk of fire.
- What to do
- Check your VIN for both recalls and have them done. If you see smoke, pull over and turn the vehicle off.
Rear axle cross pin can break (recall)
- What you'll notice
- A clunk or grinding from the rear, or the rear wheels locking up.
- Why it happens
- The cross pin inside the rear axle could fracture and cause the axle to lock.
- What to do
- Check your VIN for this recall. If you hear new rear-end noises, stop driving and have it towed.
Steering shaft bolts may be loose (recall)
- What you'll notice
- Clunking or play in the steering wheel.
- Why it happens
- Bolts on the intermediate steering shaft may not have been tightened properly, risking loss of steering.
- What to do
- Check your VIN for this recall and have it repaired before driving more than necessary.
Tie rod may separate from the rack (recall)
- What you'll notice
- Loose or wandering steering, or a clunk when turning.
- Why it happens
- A tie rod on some early 2015 trucks could come apart from the steering rack. GM told owners not to drive until inspected.
- What to do
- Do not drive until the recall inspection is done. Check your VIN right away.
Transfer case can shift into neutral (recall)
- What you'll notice
- The truck loses drive power or rolls while parked without the parking brake set.
- Why it happens
- An electrical short could shift the transfer case into neutral on its own.
- What to do
- Always use the parking brake and check your VIN for this recall.
Transmission cooler line can leak (recall)
- What you'll notice
- Red fluid drips at the front of the truck, a burning smell, or smoke from under the hood.
- Why it happens
- An oil cooler line might not be fully seated and could leak fluid onto hot parts, creating a fire risk.
- What to do
- Check your VIN for this recall. If you see smoke or smell burning fluid, pull over and shut it off.
Power steering assist can cut out (recall)
- What you'll notice
- Steering suddenly becomes heavy, then the assist returns with a jerk.
- Why it happens
- The electric power steering could briefly lose assist and then return suddenly.
- What to do
- Check your VIN for this recall and have it fixed before regular driving.
Reduced brake assist from vacuum pump (recall)
- What you'll notice
- The brake pedal feels hard and stopping takes more effort, often at low speed.
- Why it happens
- The engine-driven vacuum pump for the brake booster can lose output. GM reprogrammed the brake module to use hydraulic assist instead.
- What to do
- Check your VIN for these recalls. If the pedal turns hard, drive gently to a safe spot and have it checked before continuing.
Unintended braking on one wheel (recall)
- What you'll notice
- The truck suddenly pulls to one side at highway speed.
- Why it happens
- If a wheel-speed sensor fails, the brake system could apply the opposite brake at around highway speeds. The fix reprograms the brake module.
- What to do
- Check your VIN for this recall. If ABS or traction lights are on, get it checked before highway driving.
Cylinder deactivation lifter failure
- What you'll notice
- Ticking or tapping from the engine, misfires and a check engine light, rough idle, or loss of power.
- Why it happens
- The special lifters used to shut off cylinders can stick or collapse, and the camshaft is often damaged with them.
- What to do
- Get it diagnosed promptly. Driving with a collapsed lifter can damage the camshaft and spread metal through the engine. Use the correct oil and change it on time.
Front upper control arm welds may fail (recall)
- What you'll notice
- A clunk from the front end or steering that feels loose.
- Why it happens
- Welds on the front upper control arm might not have been done properly and could separate. GM told owners not to drive until repaired.
- What to do
- Do not drive until the recall repair is done. Check your VIN right away.
Missing transfer case part can lock wheels (do-not-drive recall)
- What you'll notice
- Often no warning; the front or rear wheels can lock up while driving.
- Why it happens
- A component was left out of some transfer cases, which can make wheels lock without warning.
- What to do
- Check your VIN now. If it is included, do not drive it until the dealer repair is done.
Fuel pump can over-pressurize and leak (recall)
- What you'll notice
- A fuel smell, or wetness near the fuel tank area.
- Why it happens
- Some fuel pumps lacked a pressure regulator and could over-pressurize the system, cracking parts and leaking fuel.
- What to do
- If you smell fuel, park it and have it towed. Check your VIN for this recall.
6.2L engine rod and crankshaft defect (recall)
- What you'll notice
- A knocking that rises with engine speed, a low oil pressure warning, rough running, or the engine shutting off while driving.
- Why it happens
- Supplier defects in the connecting rods and crankshaft can lead to bearing damage and engine failure. GM recalled affected trucks.
- What to do
- Check your VIN for this recall right away. If you hear knocking or see an oil pressure warning, stop driving and have it towed.
Rear wheels can lock up (recall)
- What you'll notice
- Often no warning; the rear wheels can lock while driving.
- Why it happens
- A transmission control valve could fail and lock the rear wheels. The fix is new control software. The 2021 recall covers diesel trucks.
- What to do
- Check your VIN for these recalls and have the software update done right away.
Rear driveshaft may fail (recall)
- What you'll notice
- Vibration or clunking from under the truck, then a sudden loss of drive power.
- Why it happens
- Internal parts of the rear driveshaft may not have been heat treated properly.
- What to do
- Check your VIN for this recall and have it fixed soon.
Fuel pump control module can fail (recall)
- What you'll notice
- The engine stumbles, loses power, or stalls.
- Why it happens
- A faulty fuel pump control module could stop the fuel pump.
- What to do
- Check your VIN for this recall and get it done before long trips.
Power steering can cut out (recall)
- What you'll notice
- Steering suddenly turns heavy when starting up or while driving.
- Why it happens
- A software problem could cause the power steering assist to stop working.
- What to do
- Check your VIN for this recall and have the update done.
No warning when brake fluid is lost (recall)
- What you'll notice
- The brake pedal travels farther or braking feels weaker, without a warning light.
- Why it happens
- Brake software might not turn on the warning light when brake fluid leaks out.
- What to do
- Check your VIN for this recall. If the pedal feels soft, stop driving and have it checked.
Wrong fuel tank on some diesels (recall)
- What you'll notice
- Usually none in normal driving.
- Why it happens
- Some diesel trucks got an incorrect fuel tank that could leak fuel in a rollover crash.
- What to do
- Check your VIN for this recall and have the tank replaced.
Front wheel hub bolts may loosen (recall)
- What you'll notice
- Clicking or clunking from a front wheel, or a vibration or wobble.
- Why it happens
- Incorrect hub bolts could loosen or deform, risking loss of control.
- What to do
- Check your VIN for this recall. If you notice new noises or wobble from a front wheel, stop driving and have it inspected.
Missing transfer case part can lock wheels (do-not-drive recall)
- What you'll notice
- Often no warning; the front or rear wheels can lock up while driving.
- Why it happens
- A component was left out of some transfer cases, which can make wheels lock without warning.
- What to do
- Check your VIN now. If it is included, do not drive it until the dealer repair is done.
Four-speed automatic slips or shifts hard
- What you'll notice
- Hard or banging shifts between first and second, the engine flaring between gears, a missing third or fourth gear, or slow reverse.
- Why it happens
- The four-speed automatic behind these V8s wears out its 3-4 clutch piston seal, sun shell and valve body parts, and heat from towing speeds it up. Owner reports for the early trucks put hard shifting at the top of the list.
- What to do
- Stop towing and have the fluid and codes checked. Slipping that is left alone burns the clutches and turns a repair into a rebuild.
Central "spider" fuel injector trouble
- What you'll notice
- Long cranking before it starts, rough idle, misfires, or a raw gasoline smell.
- Why it happens
- The central injector unit feeds each cylinder through small poppet nozzles and lines that can clog or start leaking with age. A leaking nozzle can flood a cylinder.
- What to do
- Have fuel pressure and misfire data checked. If the injector unit is bad it is normally replaced as a complete assembly. Do not ignore a fuel smell.
Intake manifold gasket leaks coolant
- What you'll notice
- Coolant level keeps dropping, a sweet smell, coolant on top of the engine, or milky oil.
- Why it happens
- The intake gaskets on these Vortec V8s are known to break down and let coolant seep out, sometimes into the oil.
- What to do
- Watch the coolant level closely. If you see milky oil or the engine overheats, stop driving and have the gaskets replaced before the engine is damaged.
Gauges stick, jump, or go dead
- What you'll notice
- The speedometer, fuel, oil pressure, or temperature needle sticks, reads wrong, or drops to zero, sometimes with warning lights flickering.
- Why it happens
- Tiny motors that move the gauge needles in the instrument cluster wear out on these trucks.
- What to do
- Have the cluster tested. It can be repaired or replaced. Do not rely on a faulty speedometer or fuel gauge.
5.3L V8 burns oil
- What you'll notice
- You keep adding oil between changes, see a low-oil warning, or notice blue smoke at startup and misfires from fouled plugs.
- Why it happens
- Oil gets past the piston rings and burns. Cylinder deactivation is widely blamed for making it worse. The 2010-2014 LC9 engines were the subject of a certified class action.
- What to do
- Check the dipstick at every fill-up and keep it full. Ask a GM dealer to run an oil consumption test and check for bulletins on your VIN.
Magnetic Ride shocks leak or knock
- What you'll notice
- Oily shocks, a knocking or uneven ride, or a "Service Suspension" message.
- Why it happens
- The adaptive shocks on these trucks are known to leak and wear early. GM issued a bulletin for diagnosing them.
- What to do
- Have the shocks inspected and the failed ones replaced, and ask the dealer about the bulletin.
10-speed harsh shifts, limp mode or "Service Transmission"
- What you'll notice
- Jerky or harsh shifts, a sudden lurch, the truck going into reduced power, or a Service Transmission message.
- Why it happens
- Owners report valve body and control problems in the 10-speed automatic, and harsh shifting is one of the most common Tahoe transmission complaints in these years.
- What to do
- Have the transmission scanned and checked for software updates and bulletins. Get it in quickly if it goes into limp mode.
Brake calibration problem while towing (recall)
- What you'll notice
- Stability control, ABS or braking feels wrong when towing a trailer.
- Why it happens
- Incorrect brake calibration could affect stability control and ABS while towing.
- What to do
- Avoid towing until the recall software update is done.
"Service 4WD" message from selector switch or position sensor
- What you'll notice
- A Service 4WD message, the lights on the 4WD selector buttons going dark, or the truck staying stuck in one drive mode.
- Why it happens
- The dash selector switch or the position sensor on the transfer case motor wears out or its connector corrodes, so the system no longer knows which mode it is in.
- What to do
- Have the 4WD codes read to tell the switch from the sensor before buying parts. Get it fixed before you need four-wheel drive, and sooner if it is stuck in low range.
Wipers quit from cracked solder in the wiper control (recall)
- What you'll notice
- The wipers run only sometimes, stop in mid sweep, or do not work at all.
- Why it happens
- Solder joints in the wiper control circuit can crack, which breaks the connection to the motor.
- What to do
- Have the control repaired or replaced. Losing the wipers in rain or snow is dangerous.
Right front seat belt may not meet crash rules (recall)
- What you'll notice
- Nothing is noticed in normal use; the belt looks and works like any other.
- Why it happens
- The right front restraint was found not to hold an occupant within the required limits in a crash.
- What to do
- Have the belt assembly inspected and replaced so the front passenger is properly protected.
A/C condenser leaks refrigerant
- What you'll notice
- The air conditioning slowly stops blowing cold and keeps needing recharges.
- Why it happens
- The combined A/C condenser and transmission cooler can crack from heat cycling. GM extended coverage on the condenser for affected VINs.
- What to do
- Have a shop leak-test the system, and ask a Chevrolet dealer whether the special coverage still applies.
Clunk felt in the steering wheel (intermediate shaft)
- What you'll notice
- A clunk or thud from under the hood that you can also feel in the steering wheel, mostly at low speed when turning or going over bumps.
- Why it happens
- The slip joint in the intermediate steering shaft between the column and the steering gear dries out and develops play. GM issued a bulletin that calls for replacing the upper intermediate shaft.
- What to do
- It is mostly an annoyance, but have the shaft and the rest of the front end checked at your next service to rule out worn steering parts.
Heater and A/C blend door actuators fail
- What you'll notice
- Clicking or ticking behind the dash, air coming from the wrong vents, or one side blowing hot while the other blows cold.
- Why it happens
- Small electric motors move the doors that direct and mix the air. Their plastic gears strip, so a door sticks or keeps hunting for its position.
- What to do
- Not urgent unless you lose defrost. Have a shop find which actuator has failed; some are easy to reach and others need dash trim removed.
Dashboard cracks
- What you'll notice
- Cracks in the top of the dashboard, often starting near the passenger airbag or the corners by the windshield, sometimes with a rattle.
- Why it happens
- The dash top on these trucks turns brittle with sun and heat and splits. There was no recall and a class action over it was dismissed.
- What to do
- It is cosmetic for most owners. A fitted dash cover hides it; replacing the dash top is the permanent fix.
Radio may not have the electronic owner's manual (recall)
- What you'll notice
- The owner information section in the radio menu is empty or will not open.
- Why it happens
- The radio was not set to download the electronic owner's manual, so required safety information is missing from the vehicle.
- What to do
- The dealer loads the manual at no charge. Use the printed manual until then.
Repair prices for your Chevrolet Tahoe
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace central (spider) fuel injector assembly
- Replace lower intake manifold gaskets and coolant
- Replace front brake rotor and hub assembly
- Inspect and tighten lower steering shaft bolt
- Install missing body and wheelhouse plugs
- Rebuild instrument cluster (replace gauge stepper motors)
- Disable or replace heated washer module (recall remedy)
- Replace pistons and rings (GM oil consumption fix)
- Replace rear axle differential cross pin
- Inspect and tighten intermediate steering shaft bolts
- Inspect and torque tie rod to steering rack
- Reprogram transfer case control module
- Reseat or replace transmission cooler line fitting
- Power steering repair or software update (recall remedy)
- Replace A/C condenser and recharge system
- Replace brake vacuum pump
- Update brake control software (recall remedy)
- Replace Magnetic Ride shocks (pair)
- Replace valve lifters and camshaft
- Replace front upper control arms
- Inspect and replace transfer case assembly
- Replace fuel pump module
- Replace engine assembly
- Transmission software update and fluid service
- Reprogram transmission control software (recall remedy)
- Replace rear driveshaft assemblies
- Replace fuel pump power control module
- Update power steering software (recall remedy)
- Recalibrate brake control module (recall remedy)
- Replace fuel tank with correct part
- Replace upper intermediate steering shaft
- Replace 4WD selector switch or transfer case position sensor
- Replace HVAC door actuator
- Replace upper dashboard panel
- Repair or replace windshield wiper control module
- Replace right front seat belt assembly
- Rebuild or replace the four-speed automatic
- Reprogram radio to download the owner's manual
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Pick a model year to see its safety recalls.