Your 2007 Chrysler PT Cruiserproblems, repair costs and recalls
What we've documented about the 2007 Chrysler PT Cruiser: problems owners and shops report, typical repair and upkeep costs, and safety recalls.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems for your 2007 Chrysler PT Cruiser
8 documented issues apply to 2007, most serious first.
Engine shuts off while driving
- What you'll notice
- The engine cuts out while driving or at stops, gauges may drop to zero or sweep up and down first, warning lights flash, and power steering goes heavy. It often restarts after a short wait, and dealers frequently find no code.
- Why it happens
- This is the most-reported PT Cruiser problem. Causes owners have found include a failing integrated power module (fuse box), ignition switch faults, bad grounds and battery cable connections, and engine computer faults.
- What to do
- Note exactly what the gauges and lights do when it happens. Have the battery cables, grounds, ignition switch and power module checked before paying for an engine computer.
Head gasket failure and overheating
- What you'll notice
- Overheating, coolant disappearing or the overflow bottle pushing coolant out, white exhaust smoke, oil burning, or low compression with misfires.
- Why it happens
- The 2.4L head gasket fails, usually after the engine has overheated from a cooling problem such as a failed fan, thermostat or water pump. Cylinder heads can warp or crack.
- What to do
- Stop driving if the gauge climbs. Have a cooling system pressure test and a compression or leak-down test; fixing the cause of overheating matters as much as the gasket.
Radiator cooling fan stops working
- What you'll notice
- The temperature gauge climbs in traffic or at idle, the A/C blows warm when stopped, or the fan area smokes or smells burnt.
- Why it happens
- The electric radiator fan motor seizes or cuts in and out. Without it the engine overheats quickly at low speeds, which can ruin the head gasket.
- What to do
- Watch the temperature gauge. If the fan doesn't run when the engine is hot or the A/C is on, get it replaced before driving in traffic.
Timing belt failure damages valves
- What you'll notice
- The engine suddenly dies and cranks fast without starting, sometimes after a slapping noise; oil-soaked belts are a warning sign.
- Why it happens
- The 2.4L uses a rubber timing belt, and the engine is built so that pistons hit the valves if the belt breaks. Oil leaks from the cam or crank seals shorten belt life.
- What to do
- Replace the timing belt (and usually the water pump) on schedule, and fix any oil leaks at the front of the engine. If it has already broken, don't keep cranking it.
Front crankshaft seal oil leak from crankshaft end play
- What you'll notice
- Sudden heavy oil loss, the oil light flickering, oil sprayed on the timing belt, or a front crank seal that keeps pushing out after being replaced.
- Why it happens
- Too much front-to-back movement (end play) in the crankshaft, from a bad thrust bearing or a machining problem in the block, pushes the front seal out. A Chrysler bulletin for 2005-2006 tells techs to measure end play.
- What to do
- Check the oil level often and stop if the oil light comes on. Ask the shop to measure crankshaft end play before just replacing the seal again.
Check engine light, rough idle and burnt valves
- What you'll notice
- Check engine light with misfire codes, rough or shaking idle, stalling, or loss of power.
- Why it happens
- Owners have found low compression from sticking or burnt valves and heads warped by overheating. A failed coolant temperature sensor can let the engine overheat unnoticed.
- What to do
- Have the misfire codes read and a compression test done. Catching a sticking valve early can avoid a full engine replacement.
Clutch won't fully release (manual)
- What you'll notice
- Grinding when shifting into reverse, hard shifting, or the car creeping with the clutch pedal down, often worse once warmed up.
- Why it happens
- Owners have traced it to a leaking clutch master or slave cylinder, poor adjustment or a failing pressure plate.
- What to do
- Have the clutch hydraulics checked first, since they are cheaper than a full clutch job.
Turn signals work erratically
- What you'll notice
- Turn signals don't flash, flash only one way, or other stalk functions (wipers, high beams) act up.
- Why it happens
- The multifunction switch on the steering column wears out.
- What to do
- Have the switch tested and replaced; working turn signals are needed to pass inspection.
Repair prices for your 2007 Chrysler PT Cruiser
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Diagnose stalling; repair grounds, ignition switch or power module
- Replace head gasket (often with timing belt and water pump)
- Replace radiator cooling fan assembly
- Replace front seal; replace crankshaft bearings or short block if end play is out of spec
- Cylinder head valve job or head replacement
- Replace clutch master/slave cylinder or clutch kit
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Checking the NHTSA recall database…