Your 2000 Daewoo Lanosproblems, repair costs and recalls
What we've documented about the 2000 Daewoo Lanos: problems owners and shops report, typical repair and upkeep costs, and safety recalls.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems for your 2000 Daewoo Lanos
14 documented issues apply to 2000, most serious first.
Camshaft position sensor can melt and start a fire (recall)
- What you'll notice
- A burning plastic smell or smoke from the engine bay, sometimes with a check engine light, stalling or a no-start.
- Why it happens
- The camshaft position sensor, which tells the engine computer where the camshaft is, can overheat and melt. The heat can spread to the cam cover and the sensor wiring and could start a fire. Recall 04V-357 replaces the sensor and adds a fuse. It is by far the most-reported Lanos problem.
- What to do
- If you smell burning or see smoke, pull over, turn the engine off and get away from the car. Daewoo's US dealer network closed, and many owners could not get the recall done, so call NHTSA's recall line with your VIN and ask a shop to check the sensor and wiring.
Daewoo's US dealers have closed, so a shop may charge for this if the recall can't be done.
Timing belt or tensioner fails and bends valves
- What you'll notice
- The engine suddenly dies while driving and cranks but won't start, sometimes after a slapping or rattling noise from the belt area.
- Why it happens
- The 1.6L engine is driven by a rubber timing belt. If the belt or its tensioner pulley fails, the valves hit the pistons and bend. Owners report failures around 70,000 to 77,000 miles, and some blame a defective tensioner arm.
- What to do
- If you don't have proof it was done, replace the timing belt, tensioner and idler pulleys now. Owners suggest doing it about every 50,000 miles and changing the water pump at the same time. If the belt has already snapped, don't keep cranking. Have it towed and ask for a compression test.
Coolant leaks and overheating
- What you'll notice
- Coolant puddles, a sweet smell, steam from under the hood, or the temperature gauge climbing. One owner's gauge gave no warning until the thermostat housing cracked.
- Why it happens
- Owners report a cracked plastic thermostat housing, a snapped coolant hose, a leaking water pump or heater hose, and intake manifold gasket leaks. Overheating can blow the head gasket and ruin the engine.
- What to do
- Check the coolant level when the engine is cold. If the gauge climbs or you see steam, pull over and turn the engine off right away. Driving even a short distance while overheating can destroy the engine.
Engine stalls or shuts off without warning
- What you'll notice
- The engine cuts out while driving, braking or parking, or won't start at all. The check engine light may be on.
- Why it happens
- Owners trace it to the camshaft or crankshaft position sensors, a throttle body fault, damaged wiring, or water getting into and ruining the engine computer.
- What to do
- If it stalls, steer to safety. Steering and brakes get heavy with the engine off. Have the codes read and the sensor wiring checked. Also make sure the cam sensor recall was done.
Headlights cut out from melted connectors
- What you'll notice
- One or both headlights go out while driving, flicker, or stop working. The plug behind the bulb may look browned or melted.
- Why it happens
- Heat from the bulb breaks down the headlight connector until it loses contact. Owners mention a service bulletin that changed the bulb type to reduce this.
- What to do
- Don't drive at night with a headlight out. Have the connector and wiring replaced, not just the bulb, and use the bulb type the shop recommends.
Floor wiring harness can chafe and stall the engine (recall)
- What you'll notice
- The engine runs poorly or suddenly stalls, often without a clear pattern.
- Why it happens
- A wiring harness under the front passenger carpet rubs against a seam in the floor and gets damaged by passengers' feet. Recall 01V-020 moves and secures the harness.
- What to do
- Ask a shop to look under the passenger carpet for chafed wires, especially if the car stalls at random. Check the VIN for open recalls.
Alloy wheel bolts can loosen (recall)
- What you'll notice
- Clunking or a wobble from a wheel, especially after hard braking.
- Why it happens
- Alloy wheels were made without steel inserts around the bolt holes, so the bolts can work loose. Recall 99V-336 re-torques the bolts to a new spec.
- What to do
- If you hear clunking from a wheel, stop and check the wheel bolts. Have all bolts torqued to the correct spec.
Rough idle or stalling when cold
- What you'll notice
- The engine idles roughly, surges or stalls until it warms up, and may be hard to start cold.
- Why it happens
- Owners trace it to a sticking EGR valve, a dirty throttle body or fuel injectors, a clogged fuel filter, or a faulty idle control motor.
- What to do
- Have the codes read. Cleaning the EGR valve and throttle body and replacing the fuel filter are cheap first steps that often help.
Brakes wear quickly, grind or calipers stick
- What you'll notice
- Grinding from the front brakes, pads and rotors wearing out every few thousand miles, a burning smell, or the car pulling when braking.
- Why it happens
- Owners report fast pad and rotor wear, warped front rotors and seized calipers. A sticking caliper keeps a pad dragging, which wears it out and overheats the brake.
- What to do
- Have the brakes inspected, including caliper slide pins and pistons. If you smell burning or the car pulls hard when braking, get it checked before driving far.
Transmission drops gears or grinds
- What you'll notice
- The automatic downshifts suddenly at highway speed, bangs into gear, slips into neutral on hills, or leaks fluid. Some manual cars grind in third gear.
- Why it happens
- Owners report internal wear and fluid leaks. Some needed a replacement transmission.
- What to do
- Check the transmission fluid level and look for leaks. If it slips or drops gears, drive gently and have it diagnosed before it leaves you stranded.
Rear wheel bearing roar
- What you'll notice
- A roaring or humming that gets louder with speed, coming from the rear. Some owners also notice looseness at a wheel.
- Why it happens
- The rear wheel bearings wear out. Owners report both failing, and failures returning after earlier repairs.
- What to do
- Have the bearings checked soon. A badly worn bearing can overheat and, in extreme cases, let the wheel wobble.
Engine mount bracket breaks
- What you'll notice
- Clunking when shifting or accelerating, heavy vibration, or the engine moving around. In one case the engine came loose and the car stalled.
- Why it happens
- An engine mount bracket can crack and break off, letting the engine shift in its compartment.
- What to do
- Have the mounts inspected if you hear clunks on takeoff. Don't keep driving if the engine is visibly loose.
Passenger airbag bracket upgrade (recall)
- What you'll notice
- Usually none, although some owners report the airbag light staying on.
- Why it happens
- The car did not meet the federal standard for head protection from the passenger airbag cover. Recall 02V-131 installs energy-absorbing mounting brackets. Many owners could not get it done after dealers closed.
- What to do
- Ask NHTSA or a shop to check your VIN for this recall. If the airbag light is on, have the system diagnosed.
Car pulls to one side
- What you'll notice
- The car drifts left or right on a straight road and needs constant steering correction.
- Why it happens
- Owners report alignment problems and worn parts. Uneven tire pressure or a sticking brake can also cause it.
- What to do
- Check tire pressures, then get an alignment and have the brakes and wheel bearings checked if it keeps pulling.
Repair prices for your 2000 Daewoo Lanos
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace timing belt, tensioner and idler pulleys
- Replace thermostat and housing
- Diagnose stalling; replace sensor or engine computer
- Clean EGR valve and throttle body, replace fuel filter
- Replace front brake pads and rotors
- Replace engine or transmission mount
- Wheel alignment
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Replace camshaft position sensor and add fuseNo charge if your vehicle is included
- Reposition and secure floor wiring harnessNo charge if your vehicle is included
- Re-torque wheel bolts to revised specNo charge if your vehicle is included
- Install energy-absorbing airbag mounting bracketsNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Checking the NHTSA recall database…