Dodge Durangoproblems, repair costs and recalls
Problems reported across 1998–2027. Pick your model year below to see what applies to your vehicle. No 2010 model year.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems
49 documented issues across all years, most serious first.
Upper ball joint wear and separation (recall 04V-596)
- What you'll notice
- A clunk from the front end over bumps, loose or wandering steering, and in the worst case a front wheel that suddenly tucks in.
- Why it happens
- Water can get into the front upper ball joints, push out the grease and corrode them. The worn joint can eventually pull apart.
- What to do
- Check the VIN for the recall. If the front end clunks or the steering feels loose, have the ball joints inspected before driving further.
Exterior lights can fail from timer module fault (recall 02V-322)
- What you'll notice
- Headlights or other exterior lights stop working or act erratically.
- Why it happens
- A fault in the central timer module, which controls the lights, can shut them off.
- What to do
- Check the VIN for the recall and avoid night driving until the lights work reliably.
Power outlet connector short and fire risk (recall 06V-339)
- What you'll notice
- A hot plastic or burning smell near the power outlets, or an outlet that stops working.
- Why it happens
- High resistance can build up in the power outlet wiring connector and overheat it.
- What to do
- Check the VIN for the recall. If you smell burning plastic, stop using the outlets and have the wiring inspected right away.
Instrument panel fire risk from gauge cluster circuit (recalls 03V-528, 07V-092)
- What you'll notice
- A burning smell or smoke from behind the dash, flickering dash or interior lights, or a gauge cluster that goes dark.
- Why it happens
- A circuit inside the instrument cluster that powers the interior lights can overheat. An earlier recall on 2004 models addressed a cracked part on the same circuit board.
- What to do
- Check the VIN for both recalls. If you smell burning from the dash, pull over, shut the vehicle off and have it towed for inspection.
Battery cable can chafe and short (recall 04V-578)
- What you'll notice
- A burning smell under the hood, a sudden loss of electrical power, or a no-start.
- Why it happens
- A battery cable can rub against nearby parts until its insulation wears through and it shorts, which can start an under-hood fire.
- What to do
- Check the VIN for the recall and have the cable routing inspected if it is open.
Throttle cable can stick open (recall 04V-020)
- What you'll notice
- The engine keeps revving or the vehicle keeps pulling after you lift off the gas pedal.
- Why it happens
- The throttle control cable can bind so the throttle does not return to idle.
- What to do
- If the throttle sticks, shift to neutral, brake firmly and pull over. Check the VIN for the recall before driving again.
Vehicle may roll away in Park (recall 05V-460)
- What you'll notice
- The vehicle creeps or rolls after being shifted into Park, especially on a slope.
- Why it happens
- A cup plug inside the automatic transmission can come loose and keep the park mechanism from holding.
- What to do
- Always set the parking brake and check the VIN for the recall right away.
ABS control module needs reprogramming (recall 05V-554)
- What you'll notice
- ABS or brake warning lights, or unusual brake or stability behavior.
- Why it happens
- A software fault in the anti-lock brake module could affect vehicle control without warning.
- What to do
- Check the VIN for the recall and have the module reprogrammed before relying on the vehicle in slippery conditions.
Rear Watts link can fail (recall 06V-240)
- What you'll notice
- A clunk from the rear suspension, or the rear end feeling loose or shifting side to side.
- Why it happens
- A part of the rear Watts link suspension, which keeps the axle centered, can fail and affect handling.
- What to do
- Check the VIN for the recall and have the rear suspension inspected before highway driving.
Fuel pump relay failure in the power module (recalls)
- What you'll notice
- The engine cranks but won't start, or it stalls while driving.
- Why it happens
- The fuel pump relay inside the under-hood power module (TIPM) can fail. Several recalls cover affected vehicles, including a follow-up for some that already had the first fix.
- What to do
- Check the VIN for open recalls and have the power module inspected if the vehicle stalls or won't start.
Brake booster corrosion (recalls)
- What you'll notice
- A hard brake pedal that takes more effort to stop the vehicle, especially in freezing weather.
- Why it happens
- Water can get into the brake booster and corrode it, reducing power assist. The water can also freeze inside it. Recalls added a shield and later rechecked it.
- What to do
- Check the VIN for the recalls and have the brakes inspected right away if the pedal feels hard.
Alternator failure (recalls)
- What you'll notice
- A battery or charging warning light, dimming lights, a burning smell, and then a sudden stall.
- Why it happens
- The alternator can fail internally without warning. On some vehicles a failing alternator can also short and start a fire.
- What to do
- Check the VIN for open recalls. Get to safety and have the charging system tested if the battery light comes on.
Lifter and camshaft wear
- What you'll notice
- A ticking sound that does not go away when warm, misfires, a rough idle and a check engine light.
- Why it happens
- Lifters can stop rolling and wear the camshaft lobes. It is widely reported and was the subject of a lawsuit, but there is no recall.
- What to do
- Have a ticking Hemi checked quickly. Early repair limits the damage to the camshaft.
ABS module fault (recalls)
- What you'll notice
- ABS and stability control warning lights, brake lights that stay on, or the shifter leaving Park without pressing the brake.
- Why it happens
- The anti-lock brake module can develop a fault that affects several systems. A later recall replaced the earlier fix.
- What to do
- Check the VIN for open recalls and have it repaired soon.
Steering rack can bind (recall 22V-154)
- What you'll notice
- Steering feels stiff, sticky or notchy, especially at low speed.
- Why it happens
- The steering rack bar may not have been properly hardened, which can cause binding. Dealers replace the steering gear.
- What to do
- Check the VIN for the recall and stop driving if the steering becomes hard to turn.
Fuel tank strap can separate (recall 99V-342)
- What you'll notice
- Often no warning. You may hear a clunk or scraping from under the rear of the truck, or see the fuel tank hanging low.
- Why it happens
- A strap that holds the fuel tank can come apart, letting the tank sag or drop.
- What to do
- Have this checked right away if the recall was never done. The repair is free at a dealer. Ask the dealer to check your VIN to see if it was already done.
Rear brake tube can wear through (recall 99V-341)
- What you'll notice
- Brake fluid spots under the rear of the truck, a low or soft brake pedal, or a red brake warning light.
- Why it happens
- A rear brake line can rub against nearby parts until it wears through and leaks fluid.
- What to do
- Do not drive with a soft pedal or a brake fluid leak. The repair is free at a dealer. Ask the dealer to check your VIN to see if it was already done.
Alternator cable fastener can loosen and arc (recall 98V-019)
- What you'll notice
- Battery light, dim lights, a burning smell or sparks under the hood.
- Why it happens
- The nut holding the main cable to the alternator can work loose, and the loose connection can spark and overheat.
- What to do
- Stop driving if you smell burning or see sparks. The repair is free at a dealer. Ask the dealer to check your VIN to see if it was already done.
Shifter can leave Park without the brake pressed (recall 07V-555)
- What you'll notice
- The shifter can be moved out of Park without your foot on the brake, sometimes with the key out.
- Why it happens
- The lock that holds the shifter in Park can fail.
- What to do
- Always set the parking brake until this is fixed, because the truck can roll away. The repair is free at a dealer. Ask the dealer to check your VIN to see if it was already done.
Transfer case may not fully engage and truck can roll (recall 01V-077)
- What you'll notice
- On four-wheel-drive trucks, the truck may roll while the shifter is in Park.
- Why it happens
- The transfer case can end up between gears, in a neutral spot, so Park no longer holds the wheels.
- What to do
- Always set the parking brake and have the recall done promptly. The repair is free at a dealer. Ask the dealer to check your VIN to see if it was already done.
Airbag inflators can rupture (do-not-drive recalls)
- What you'll notice
- Usually no warning at all before a crash.
- Why it happens
- The driver and passenger airbag inflators can burst when the airbag fires and spray metal pieces into the cabin.
- What to do
- Do not drive until the recall is completed. Dealers will tow and repair the truck for free. Ask the dealer to check your VIN for open recalls.
Right steering knuckle can fracture (recall 06V-386)
- What you'll notice
- A sudden clunk and loss of control at the right front wheel.
- Why it happens
- The right front steering knuckle may have been made with a flaw that lets it crack.
- What to do
- Have the recall checked before driving much further. The repair is free at a dealer. Ask the dealer to check your VIN to see if it was already done.
Engine computer software can briefly lock the drive wheels (recall 06V-341)
- What you'll notice
- A sudden jolt or skid from the driven wheels, mostly when slowing down.
- Why it happens
- A fault in the engine computer programming can make the drive wheels lock for a moment.
- What to do
- Get the software update done promptly. The repair is free at a dealer. Ask the dealer to check your VIN to see if it was already done.
Rear axle pinion nut can loosen (recall 13V-038)
- What you'll notice
- Whine, clunk or vibration from the rear axle. In the worst case the rear wheels lock up.
- Why it happens
- The nut holding the pinion gear in the rear axle can back off, letting the gears move out of place.
- What to do
- Stop driving if you hear new rear axle noise and have the recall checked. The repair is free at a dealer. Ask the dealer to check your VIN to see if it was already done.
Cruise control may not switch off (recall 18V-332)
- What you'll notice
- Cruise control keeps holding or gaining speed even after you tap the brake or press Cancel.
- Why it happens
- If a short happens in a certain wiring network while the truck is accelerating under cruise, the system may not shut off.
- What to do
- If it happens, brake firmly and shift to Neutral, then stop. Get the software update done. The repair is free at a dealer. Ask the dealer to check your VIN to see if it was already done.
Left front brake caliper can crack (recall 16V-168)
- What you'll notice
- Soft brake pedal, pull to one side when braking, or brake fluid at the left front wheel.
- Why it happens
- The left front caliper casting may have a flaw that lets it crack.
- What to do
- Do not drive with a soft pedal or fluid leak. The repair is free at a dealer. Ask the dealer to check your VIN to see if it was already done.
Rear lower control arm can fracture (recall 15V-469)
- What you'll notice
- Clunk from the rear, the rear end feels loose or wanders.
- Why it happens
- A rear lower control arm may not have been heat-treated correctly and can break.
- What to do
- Have it replaced before driving further if the recall is open. The repair is free at a dealer. Ask the dealer to check your VIN to see if it was already done.
Fuel rail crossover tube can leak (recall 16V-814)
- What you'll notice
- Strong raw fuel smell from under the hood.
- Why it happens
- On some V6 engines built in early 2016 the tube that joins the two fuel rails can leak.
- What to do
- Stop driving if you smell fuel under the hood, because of the fire risk. The repair is free at a dealer. Ask the dealer to check your VIN to see if it was already done.
Rear axle shafts may be too short and disengage (recall 17V-541)
- What you'll notice
- Loss of drive, or the truck rolls while in Park.
- Why it happens
- Some rear half shafts were made too short and can slip out of the axle.
- What to do
- Use the parking brake every time and have the recall done promptly. The repair is free at a dealer. Ask the dealer to check your VIN to see if it was already done.
EGR valve can stick open and cut power (recall 22V-284)
- What you'll notice
- Check engine light, rough running, and a sudden loss of power or stall.
- Why it happens
- The exhaust gas recirculation valve on the V6 can stick open.
- What to do
- Have it fixed promptly, since the engine can lose power in traffic. The repair is free at a dealer. Ask the dealer to check your VIN to see if it was already done.
Shifter may slip out of Drive (recall 22V-866)
- What you'll notice
- The transmission drops out of Drive, or the truck is not really in Park.
- Why it happens
- A shifter part was not hardened correctly at the factory.
- What to do
- Use the parking brake every time and have the recall done promptly. The repair is free at a dealer. Ask the dealer to check your VIN to see if it was already done.
Dash-mounted shifter can come out of gear (recall 23V-640)
- What you'll notice
- On trucks with the shifter on the instrument panel, the transmission can leave the gear you chose.
- Why it happens
- The shifter may not hold its position.
- What to do
- Use the parking brake every time and have the recall done promptly. The repair is free at a dealer. Ask the dealer to check your VIN to see if it was already done.
Oil sludge can choke and ruin the 4.7L V8
- What you'll notice
- Low oil pressure or an oil light at idle, ticking from the top of the engine, loss of power, and thick black paste on the dipstick or under the oil cap.
- Why it happens
- These engines are hard on oil and sludge builds up in the passages when oil changes are stretched or the engine runs hot. The sludge starves the camshafts and bearings.
- What to do
- Stop driving if the oil light comes on and have the oil pressure checked. Short oil change intervals are the only real protection on this engine.
Dropped valve seat on the 3.7L V6
- What you'll notice
- A sudden heavy misfire on one cylinder, a flashing check engine light and a big loss of power, often after the engine has been run hot.
- Why it happens
- Overheating lets a valve seat work loose from the aluminum cylinder head. The loose seat then batters the valve and the cylinder.
- What to do
- Pull over and stop driving if the check engine light flashes. Keep the cooling system healthy and never ignore a rising temperature gauge.
Windshield wiper motor can quit (recall 04V-216)
- What you'll notice
- The wipers slow down, stop partway, or stop working in the rain.
- Why it happens
- The wiper module motor can fail, leaving the driver without clear vision.
- What to do
- Check the VIN for the recall and have the wiper motor replaced if it is open.
Windshield wiper motor can stop working (recall 06V-067)
- What you'll notice
- The wipers stop working in some conditions.
- Why it happens
- The front wiper motor can lose its ability to wipe, which blocks the driver's view in bad weather.
- What to do
- Check the VIN for the recall and have the wiper motor replaced if it is open.
Left cylinder head valve seat problem (warranty extension)
- What you'll notice
- A ticking noise from the engine, a rough idle or misfire, and a check engine light, usually pointing to cylinder 2.
- Why it happens
- A valve seat in the left cylinder head could wear or loosen on some early Pentastar engines. Chrysler extended the warranty on the left head for affected vehicles.
- What to do
- Have the misfire diagnosed soon and ask the dealer whether the head warranty extension applies to your VIN.
Oil filter housing and oil cooler leaks
- What you'll notice
- Oil pooling at the back of the engine, a burning oil smell, coolant loss, or oil and coolant mixing.
- Why it happens
- The plastic oil filter housing that also holds the oil cooler can crack or its gaskets can leak after many heat cycles.
- What to do
- Have the leak confirmed and the housing replaced. Do not let oil drip onto hot exhaust parts.
Rear spoiler can crack and come loose (recalls)
- What you'll notice
- Rubbing or a gap at the roof spoiler when the liftgate opens, or cracked spoiler edges.
- Why it happens
- The rear spoiler may sit out of line with the roof, so the liftgate hits it when opened. A damaged spoiler can fly off on the road.
- What to do
- Check the VIN for the recalls and have a cracked spoiler repaired before highway driving.
Clockspring can break and disable the driver airbag (recall 01V-153)
- What you'll notice
- Airbag light stays on. The horn or steering wheel buttons may also quit.
- Why it happens
- Material inside the steering wheel can damage the clockspring, the coiled wire that connects the airbag while the wheel turns.
- What to do
- Get an airbag light checked soon, since the driver airbag may not work in a crash. The repair is free at a dealer. Ask the dealer to check your VIN to see if it was already done.
Fuel filler tube valve may not close (recalls 05V-034, 09V-003)
- What you'll notice
- Fuel smell near the rear of the truck, mostly after filling up.
- Why it happens
- A one-way valve in the fuel filler tube may not seal fully, which could let fuel escape in a crash.
- What to do
- Have it checked soon. The repair is free at a dealer. Ask the dealer to check your VIN to see if it was already done.
Sun visor vanity light wiring can short (recall 14V-391)
- What you'll notice
- Vanity mirror light quits, or a burning smell or smoke near the sun visor.
- Why it happens
- Wiring for the lighted mirror can be pinched after headliner work and short out.
- What to do
- Have it inspected soon, sooner if you smell burning. The repair is free at a dealer. Ask the dealer to check your VIN to see if it was already done.
Radio software can be accessed remotely (recall 15V-461)
- What you'll notice
- No symptom in normal use.
- Why it happens
- A weakness in the touchscreen radio software could let an outsider reach vehicle controls.
- What to do
- Have the software updated at a dealer or with the USB update from the maker.
Side curtain airbag fastener may be loose or missing (recall 21V-280)
- What you'll notice
- Usually nothing you can see or hear.
- Why it happens
- A fastener holding the side curtain airbag may be loose or missing, so the bag may not protect properly in a crash.
- What to do
- Have it inspected soon. The repair is free at a dealer. Ask the dealer to check your VIN to see if it was already done.
Rearview camera image may not show (recall 24V-436)
- What you'll notice
- Blank or frozen screen when you shift into Reverse.
- Why it happens
- A radio software fault can block the camera picture.
- What to do
- Check behind you by other means and get the update soon. The repair is free at a dealer. Ask the dealer to check your VIN to see if it was already done.
ABS module may switch off stability control (recall 24V-415)
- What you'll notice
- ABS and stability control warning lights on.
- Why it happens
- A fault in the ABS control module can disable stability control.
- What to do
- Drive gently and have it fixed soon. The repair is free at a dealer. Ask the dealer to check your VIN to see if it was already done.
Tail light wiring terminals may be damaged (recall 26V-701)
- What you'll notice
- A tail light is out or flickers, or a bulb warning shows.
- Why it happens
- Terminals in the tail light wiring harness may have been damaged at the factory.
- What to do
- Have it fixed soon so drivers behind can see you. The repair is free at a dealer. Ask the dealer to check your VIN to see if it was already done.
Broken exhaust manifold bolts tick on a cold start
- What you'll notice
- A tick or tap that is loudest on a cold start and fades as the engine warms, sometimes with an exhaust smell under the hood.
- Why it happens
- The bolts that hold the exhaust manifolds to the cylinder heads snap after years of heating and cooling, and the joint then leaks.
- What to do
- Have the broken bolts and gasket replaced. A leaking manifold upsets the oxygen sensor readings and can let fumes reach the cabin.
Backup camera image stays on after leaving Reverse (recall 20V-191)
- What you'll notice
- The rear camera picture stays on the screen after you shift into Drive.
- Why it happens
- A radio software fault keeps showing the camera image.
- What to do
- Get the software update when convenient. The repair is free at a dealer. Ask the dealer to check your VIN to see if it was already done.
Repair prices for your Dodge Durango
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace front upper ball joints and align
- Replace exterior lighting timer module
- Replace windshield wiper motor
- Repair power outlet wiring connector
- Install fuse and repair gauge cluster circuit
- Reroute or replace battery cable
- Replace throttle cable
- Inspect and repair transmission park mechanism
- Reprogram ABS control module
- Replace rear Watts link parts
- Replace integrated power module (TIPM)
- Replace brake booster
- Replace alternator
- Replace left cylinder head
- Replace oil filter housing and oil cooler assembly
- Replace camshaft and lifters
- Reprogram or replace ABS control module
- Replace steering rack and align
- Replace rear roof spoiler
- Replace fuel tank straps
- Replace and re-route rear brake tube
- Inspect and secure alternator cable
- Replace clockspring
- Repair shift interlock
- Transfer case shift repair
- Replace fuel filler tube check valve
- Replace airbag inflators
- Replace right steering knuckle
- Reprogram powertrain control module
- Secure rear axle pinion nut
- Re-route sun visor lamp wiring
- Update radio software
- Replace left front brake caliper
- Replace rear lower control arms
- Replace fuel rail
- Replace rear half shafts
- Inspect and secure side curtain airbag
- Replace EGR valve
- Replace shifter assembly
- Repair shifter assembly
- Replace or reprogram ABS module
- Repair tail light harness
- Replace sludged 4.7L V8 engine
- Replace broken exhaust manifold bolts and gaskets
- Replace cylinder head on 3.7L V6
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Pick a model year to see its safety recalls.