Your 2003 Dodge Intrepidproblems, repair costs and recalls
What we've documented about the 2003 Dodge Intrepid: problems owners and shops report, typical repair and upkeep costs, and safety recalls.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems for your 2003 Dodge Intrepid
11 documented issues apply to 2003, most serious first.
Oil sludge leading to engine failure
- What you'll notice
- Ticking or knocking from the engine, an oil pressure light that flickers at idle, low idle speed, and in bad cases the engine shuts off or seizes while driving, often around 80,000 to 100,000 miles.
- Why it happens
- The 2.7L V6 is widely known for building up thick oil sludge that blocks oil passages and starves the bearings and timing chain. Long oil-change intervals and heat make it worse, and a leaking internal water pump can add coolant to the oil.
- What to do
- Change the oil and filter every 3,000 to 5,000 miles with a quality oil, and watch the oil light. If you hear knocking or the oil light flickers, stop driving and have oil pressure checked. A failed engine usually means a replacement engine.
Internal water pump leaks coolant into the oil
- What you'll notice
- Coolant level keeps dropping with no puddle under the car, a sweet smell, milky or foamy oil on the dipstick, overheating, or the engine stalling or seizing.
- Why it happens
- On the 2.7L the water pump sits inside the engine behind the timing cover and is driven by the timing chain. When its seal fails, coolant can leak straight into the oil, ruining the bearings.
- What to do
- If coolant is disappearing or the oil looks milky, stop driving and have the cooling system pressure tested. Replacing the pump means removing the timing cover, so most shops replace the timing chain parts at the same time.
Timing chain stretch or breakage
- What you'll notice
- A rattle from the front of the engine, a check engine light, rough running, or the engine suddenly quitting and refusing to restart. A broken chain can bend the valves.
- Why it happens
- Sludge and poor oil flow wear the 2.7L's timing chain, guides and tensioners, and metal debris in the oil is often found with a stretched chain.
- What to do
- Have any new rattle checked right away. Catching a stretched chain before it breaks keeps the repair to the timing parts instead of a cylinder head or engine.
Engine knocking and bearing failure
- What you'll notice
- A deep knock from the engine that gets louder with speed, often followed by complete engine failure around 100,000 miles.
- Why it happens
- Restricted oil flow from sludge wears the bearings on the 2.7L V6. Engine failure is the most-reported problem on these years.
- What to do
- Stop driving when you hear a deep knock and have oil pressure checked. Most cars with a failed bottom end get a replacement engine.
Automatic transmission slipping, harsh shifting or failure
- What you'll notice
- Slipping between gears, delayed or harsh shifts, the car stuck in one gear (limp mode), refusal to shift out of first, or no drive at all.
- Why it happens
- The front-drive automatic used in these cars wears internally, and solenoid, servo and torque converter faults are commonly reported. Old or low fluid speeds up the wear.
- What to do
- Check the fluid level and condition and have codes read. Chrysler requires its own ATF+4-type fluid, so make sure the shop uses the right one. A slipping unit usually needs a rebuild or a remanufactured transmission.
Timing belt failure if replacement is overdue
- What you'll notice
- No warning in most cases: the engine suddenly quits and won't restart. Because these engines are interference designs, the valves can be damaged.
- Why it happens
- The 3.2L and 3.5L V6 use a rubber timing belt with a 100,000-mile factory interval. A belt that is overdue can snap.
- What to do
- If your car is near or past 100,000 miles with no record of a belt change, have it replaced along with the water pump and tensioner.
Steering rack and tie rod wear
- What you'll notice
- Clunking or creaking when turning, especially when cold, loose or wandering steering, a car that won't hold an alignment, or uneven tire wear.
- Why it happens
- Worn steering rack mounting bushings, inner tie rods and the rack itself are among the most reported complaints on these LH-platform cars.
- What to do
- Have the rack mounts and tie rods inspected for play. Worn parts make the car harder to control, so do not put this off. A rack replacement is followed by an alignment.
Stalling or no-start from cam or crank sensor
- What you'll notice
- The engine cranks but won't start, stalls while driving or at a stop, or stumbles, often with a check engine light.
- Why it happens
- A failing camshaft or crankshaft position sensor, or damaged wiring to it, stops the computer from knowing engine position.
- What to do
- Have the codes read. These sensors are inexpensive, but test the wiring and connector too so the problem doesn't come back.
Oil pressure light flickers at idle
- What you'll notice
- The oil light flickers or comes on at idle or when stopped, then goes out when you press the gas.
- Why it happens
- Low oil pressure at idle is often an early sign of sludge or worn bearings in the 2.7L V6, though a bad sender can also cause it.
- What to do
- Check the oil level now. Have a mechanic measure real oil pressure with a gauge before assuming it is just the sensor.
Coolant leak from heater tube O-ring
- What you'll notice
- Coolant dripping at the front of the engine, a low coolant level, or a sweet smell after driving.
- Why it happens
- On the 3.2L and 3.5L the front heater tube O-ring hardens with age, and the metal tube can rust through from the inside.
- What to do
- Top up with the correct coolant and have the leak found. Replace the tube and O-ring together.
Overheating from worn water pump impeller
- What you'll notice
- The temperature gauge climbs, especially in traffic, even though no leak is visible.
- Why it happens
- The water pump on the 3.2L and 3.5L has a plastic impeller that can erode from rust and sediment, so it moves less coolant.
- What to do
- Stop if the gauge goes into the red. Have the cooling system pressure tested and the pump checked; it is usually replaced with the timing belt.
Repair prices for your 2003 Dodge Intrepid
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace engine with used or remanufactured 2.7L
- Replace water pump (timing cover removal), often with timing chain parts
- Replace timing chain, guides and tensioners
- Replace engine with used or remanufactured unit
- Replace automatic transmission with remanufactured unit
- Replace power steering rack and pinion, then align
- Replace crankshaft or camshaft position sensor
- Test oil pressure; replace oil pressure sender and change oil
- Replace timing belt, tensioner and water pump
- Replace front heater tube and O-ring
- Replace water pump (usually with timing belt)
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Checking the NHTSA recall database…