Your 2010 Dodge Nitroproblems, repair costs and recalls
What we've documented about the 2010 Dodge Nitro: problems owners and shops report, typical repair and upkeep costs, and safety recalls.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems for your 2010 Dodge Nitro
17 documented issues apply to 2010, most serious first.
Power module (TIPM) failure causes random electrical faults
- What you'll notice
- The horn honks on its own, wipers or washers run by themselves, headlights or dome lights flash, doors lock and unlock, and warning lights fill the dash. Some trucks won't start or stall.
- Why it happens
- The Totally Integrated Power Module (TIPM) under the hood is the fuse and relay box that also has its own computer. On the Nitro its internal circuits and relays fail, sending power to the wrong places or cutting it off.
- What to do
- Have a shop scan the body and TIPM codes before replacing parts. Pulling the horn fuse can stop a stuck horn for now. A new or properly remanufactured and programmed TIPM is the usual fix.
Engine stalls or shuts off while driving
- What you'll notice
- The engine cuts out at low speed or in traffic, often with dash lights flickering and the A/C or windows acting up at the same moment. Sometimes it restarts right away and sometimes it won't.
- Why it happens
- Most reports trace back to the TIPM power module losing power to the fuel pump or engine computer. Early 2007 trucks also had TIPM software that could stall the engine (covered by a recall).
- What to do
- Stalling while driving is dangerous, so get it checked promptly. Ask a dealer to confirm all recalls are done, then have the TIPM and fuel pump relay circuit tested.
Transmission shudder, slipping or hard shifts
- What you'll notice
- A shudder or vibration at low to moderate speeds under light throttle, slipping between gears, harsh or delayed shifts, or hesitation pulling away.
- Why it happens
- The torque converter clutch and the transmission's shift programming are the usual causes. Chrysler released computer reflashes for shudder and surge, and some trucks needed a new torque converter.
- What to do
- Check the transmission fluid level and condition, then ask a dealer whether software updates are available for your truck. If the shudder stays after an update, have the torque converter inspected.
Automatic transmission whine or failure
- What you'll notice
- A whining or howling noise from under the truck, the transmission getting stuck in one gear (limp mode), or no upshifts on the highway.
- Why it happens
- Internal wear in the automatic transmission. Owners report failures from about 50,000 to 95,000 miles, often after earlier shudder or hard-shift complaints.
- What to do
- Stop towing or driving hard and get a transmission scan and fluid check. If it is stuck in one gear, a shop needs to check whether it is an electrical fault or internal damage before rebuilding.
Rear differential seal leak and bearing failure
- What you'll notice
- Gear oil drips near the rear axle, a whine or growl from the rear that changes with speed, and in bad cases the rear wheels can lock up.
- Why it happens
- The rear axle pinion seal leaks, and if the gear oil runs low the bearings and gears wear and can seize.
- What to do
- Check under the rear axle for wet spots and have the gear oil level checked. A leaking seal is a fairly cheap fix; waiting until it howls can mean a full rebuild or a new axle.
Dropped valve seat and misfire on the 3.7L V6
- What you'll notice
- A check engine light with a misfire, a ticking or knocking sound, and a sudden loss of power. The engine may run on five cylinders.
- Why it happens
- The 3.7L runs hot, and a pressed-in valve seat can loosen and come out of the cylinder head. That kills compression in one cylinder and can damage the piston.
- What to do
- Don't keep driving with a flashing check engine light. A compression test will show whether a valve seat has dropped. Usually the cylinder head must be rebuilt or replaced, and if the piston is damaged the engine may need replacing.
Steering wheel emblem can come loose in an airbag deployment (recall)
- What you'll notice
- The emblem in the middle of the steering wheel may be loose or missing. There may be no other sign.
- Why it happens
- The emblem or its nuts can come off and fly toward the driver if the airbag deploys. Recall 20V-396 covers 2007-2011 Nitros.
- What to do
- Check your VIN for open recalls. The dealer installs a new driver airbag cover for free.
ABS hydraulic unit can leak brake fluid (recall)
- What you'll notice
- Brake fluid level drops, the brake pedal feels soft or travels farther, or the brake warning light comes on.
- Why it happens
- A defect in the ABS hydraulic control unit on some 2010 trucks could let brake fluid escape. Recall 10V-315.
- What to do
- A soft pedal is a safety issue; don't drive it far. Check your VIN for this recall.
Brake booster pushrod clip may come off (recall)
- What you'll notice
- Usually no warning, but if the clip comes off the brake pedal can suddenly stop working.
- Why it happens
- A retaining clip that connects the brake pedal to the brake booster rod may not have been installed correctly. Recall 10V-009.
- What to do
- Check your VIN for open recalls; the dealer inspects and fixes it free.
Fuel spits back at the pump or tank cracks near the filler
- What you'll notice
- The pump nozzle keeps clicking off or fuel spills out while filling, sometimes with an EVAP or gas cap warning. Some owners find a crack at the top of the tank near the filler neck.
- Why it happens
- A blocked vent or fault in the tank's evaporative (EVAP) venting stops air from escaping as fuel goes in. In some cases the tank itself was faulty and had to be replaced.
- What to do
- Fill slowly in the meantime and don't top off. Have the EVAP vent lines and tank checked; spilled fuel is a fire risk, so don't put it off.
Power window regulator breaks or window won't go up
- What you'll notice
- A window drops into the door, goes down but won't come back up, grinds or clicks, or only works from the driver's switch.
- Why it happens
- The window regulator's cable and plastic pulleys break. Less often, the driver's master switch fails.
- What to do
- Tape or cover the window if it won't close. A shop will test the switch first, then replace the regulator (often sold with the motor) if the cable has snapped.
Heater fan stops working or works only on high
- What you'll notice
- No air from the vents at any setting, or the fan only blows on the highest speed.
- Why it happens
- The blower motor wears out, or the blower resistor or fan switch fails, which leaves only the high-speed circuit working.
- What to do
- If it works only on high, the resistor is the likely part. If it never runs, a shop will check power at the blower motor before replacing it.
A/C blows warm air
- What you'll notice
- The air conditioning blows warm or only slightly cool air, sometimes after working fine on a cool morning.
- Why it happens
- Refrigerant leaks at lines and O-rings, a failed A/C clutch relay or compressor, or a bad blend door are the reported causes.
- What to do
- Have a shop check the refrigerant charge with leak dye before simply refilling it. A relay is a cheap fix; a compressor costs much more.
No start from anti-theft key system
- What you'll notice
- The engine won't start or cranks and then dies, and the security light may flash. Remote locking may also stop working.
- Why it happens
- The anti-theft key module (SKREEM/WCM) can lose communication with the key, sometimes after static discharge, so the engine computer blocks starting.
- What to do
- Try the spare key. If it still won't start, a dealer or locksmith with a scan tool can check the immobilizer and reprogram or replace the module.
Rear brakes and rotors wear out early
- What you'll notice
- Grinding or squealing from the rear, or being told the rear rotors are worn out well before the front brakes.
- Why it happens
- Owners report the rear rotors and pads wearing faster than expected, and sticking calipers causing uneven pad wear.
- What to do
- Ask for pad and rotor measurements at each oil change. If one side wears faster, have the calipers and slide pins checked.
Front head restraint pops forward on its own
- What you'll notice
- A front headrest suddenly snaps forward with a bang while driving or parked and won't go back.
- Why it happens
- The active head restraint is spring-loaded to move forward in a rear crash. A striker pin in the release mechanism can let go without a crash. Chrysler extended the warranty on this part.
- What to do
- Don't force it back. Ask a dealer about the active head restraint warranty extension for your VIN.
Power door locks stop working or cycle on their own
- What you'll notice
- One or more doors won't lock or unlock with the switch or remote, or the locks cycle by themselves.
- Why it happens
- Door lock actuators wear out. Locks that cycle on their own usually point to the TIPM power module.
- What to do
- Note which doors are affected. One dead door is usually its actuator; random locking on all doors calls for a TIPM check.
Repair prices for your 2010 Dodge Nitro
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace and program TIPM power module
- Diagnose stalling; replace TIPM or fuel pump relay as needed
- Transmission software update, fluid service or torque converter replacement
- Rebuild or replace automatic transmission
- Replace pinion seal, or rebuild rear differential if bearings are worn
- Rebuild or replace cylinder head
- Repair EVAP vent or replace fuel tank
- Replace window regulator (and motor if needed)
- Replace blower motor or blower resistor
- A/C leak test and recharge, or compressor replacement
- Diagnose immobilizer and reprogram or replace key module
- Replace door lock actuator
- Replace rear pads and rotors
- Inspect striker pin and replace active head restraint
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Replace driver airbag coverNo charge if your vehicle is included
- ABS hydraulic unit recall repairNo charge if your vehicle is included
- Inspect and install brake booster clipNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Checking the NHTSA recall database…