Your 1997 Ford Aerostarproblems, repair costs and recalls
What we've documented about the 1997 Ford Aerostar: problems owners and shops report, typical repair and upkeep costs, and safety recalls.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems for your 1997 Ford Aerostar
26 documented issues apply to 1997, most serious first.
Automatic transmission harsh shifts, slipping or failure
- What you'll notice
- Hard clunks on the 1-2 or 2-1 shift, a shudder going into overdrive, a flashing O/D light, slipping, or the van refusing to move. Owners report repeat failures at higher mileage.
- Why it happens
- The 4R44E and 4R55E four-speed automatics (and the 5R55E five-speed added for 1997 with the 4.0L) wear their overdrive band, drum and seals, and the electronic pressure control solenoid and valve body can stick. Ford issued bulletins on wiring harness, torque converter and cooler contamination for these units.
- What to do
- Have the codes read if the O/D light flashes and check the fluid level and smell. If it slips or won't engage, stop driving it hard. A rebuilt or used transmission is usually the sensible fix on a van this age, and the cooler lines should be flushed at the same time.
All-wheel-drive transfer case can break and spray fluid (recall)
- What you'll notice
- On AWD vans: a loud bang or vibration from under the van, fluid sprayed on the exhaust, a burning smell, or sudden loss of drive.
- Why it happens
- Driveline vibration and a shifting bushing at the transfer case output shaft could crack the transmission or transfer case. Fluid could reach the hot exhaust and start a fire, or the driveshaft could separate. Ford recalled AWD Aerostars and installed a new bushing and an aluminum driveshaft.
- What to do
- If you smell burning fluid or hear a bang from underneath, pull over safely and turn the engine off. Have a Ford dealer check that the recall was done on your VIN.
Ask a Ford dealer with your VIN whether the recall was completed.
Ignition switch can overheat and catch fire (recall)
- What you'll notice
- Smoke or a hot smell from the steering column, a hot key, dash gauges or fuses that quit, or the engine starting without the key fully inserted.
- Why it happens
- Ford built these vans with more electrical load on the ignition switch's accessory circuit than the switch was designed for. The contacts can arc, short and overheat. Ford's fix was a jumper harness with a relay that takes the load off the switch.
- What to do
- If you see smoke or smell burning near the column, turn the key off and get everyone out. Have a Ford dealer confirm the recall relay harness was installed.
Ask a Ford dealer with your VIN whether the recall was completed.
Accelerator cable can fray and stick (recall)
- What you'll notice
- The engine is slow to drop back to idle when you lift off the gas, the pedal feels sticky, or the van keeps pulling after you release the pedal.
- Why it happens
- Some 1997 vans with the 3.0L engine had the accelerator cable kinked during assembly, so the inner wires fray and drag. Owners also filed complaints about runaway speed and throttle cables coming loose from the pedal.
- What to do
- If the throttle sticks, shift to neutral and brake hard, then turn the engine off once stopped. Have a Ford dealer check that the new cable from the recall was fitted.
Ask a Ford dealer with your VIN whether the recall was completed.
Aluminum wheels crack at the spokes
- What you'll notice
- A wobble or vibration at speed, a clicking or roaring noise from a wheel, or visible cracks around the spokes or lug holes. Some owners found several cracked wheels.
- Why it happens
- Dozens of owners reported the factory 14-inch alloy wheels cracking under the van's weight. Ford did not recall them, and some shops called it a design weakness.
- What to do
- Look closely at each wheel, front and back, around the spokes and lug holes. Do not drive on a cracked wheel; replace it with a sound wheel of the right load rating.
Front wheel bearing failure
- What you'll notice
- Grinding or roaring from a front wheel that gets worse with speed, play in the wheel, or a pull to one side. In severe cases owners reported the spindle breaking and the wheel coming off.
- Why it happens
- Worn front wheel bearings that are not serviced can overheat and seize, damaging the spindle, rotor and caliper.
- What to do
- Have a grinding front wheel checked right away. A shop can check bearing play with the wheel off the ground; repacking or replacing the bearings early is far cheaper than a spindle.
Rear axle bearing, seal or shaft failure
- What you'll notice
- A growl or grinding from the rear, gear oil on the inside of a rear tire or brake drum, or, in rare cases, a broken axle shaft.
- Why it happens
- Owners reported rear axle bearings and seals failing, sometimes blamed on rear brakes dragging and heating the axle end. One reported a broken rear axle shaft.
- What to do
- Look for oil on the inside of the rear wheels. Have a noisy or leaking rear axle checked soon; a failed bearing can let the shaft move.
Brakes fade or lose power after heavy use
- What you'll notice
- A soft or low pedal, longer stops, or brakes that barely work after a long downhill run or heavy load.
- Why it happens
- Owners reported brake loss, including one case where a mechanic found the calipers baked brittle by heat. The front brakes on these heavy vans work hard, and old fluid boils more easily.
- What to do
- If the pedal goes soft, stop as soon as it is safe and have the brakes inspected before driving further. Flush old brake fluid and check calipers and hoses.
Warped front rotors and pulsing brakes
- What you'll notice
- The steering wheel or brake pedal shakes when stopping, the van jerks or pulls under braking, sometimes with pads that still look good.
- Why it happens
- Owners filed many complaints of front rotors warping or cracking early. Ford issued several brake vibration and rotor machining bulletins for these vans.
- What to do
- Have the rotors measured. Replacing them is often better than machining thin rotors, and avoid long downhill braking with a heavy load.
Rear ABS warning light comes on
- What you'll notice
- The ABS or brake warning light comes on, sometimes on and off, and the rear wheels may lock on hard stops.
- Why it happens
- These vans use a rear-wheel anti-lock system. Ford issued a bulletin for the rear ABS light, and owners report intermittent ABS lights and rear lock-up.
- What to do
- Check the brake fluid level first. Then have the ABS codes read; a sensor, wiring or the rear ABS valve is usually at fault. Normal braking without ABS still works.
Oil leaks from the rear main seal and oil pan
- What you'll notice
- Oil spots under the middle of the van, an oily underside, or burning oil smell after driving.
- Why it happens
- RepairPal owners commonly report leaks at the rear crankshaft seal and oil pan gasket. Ford issued several bulletins on repairing oil pan gasket leaks that come back after a repair.
- What to do
- Find the source before replacing parts and keep the oil topped up. A pan gasket is a moderate job; the rear main seal needs the transmission out, so it is often done during transmission work.
Knocking noise from the 4.0L engine
- What you'll notice
- A knock or tick that sounds like a bad rod bearing, often loudest on a cold start, then quieter as it warms up.
- Why it happens
- Ford issued bulletins for 4.0L engine noise that can be mistaken for rod or piston knock, plus cold-start knock, and for oil priming after engine repairs. Low or old oil makes it worse.
- What to do
- Check the oil level and have the oil pressure tested before assuming the worst. If the knock stays when warm or the oil light flickers, stop driving and get it diagnosed.
Thumping coolant hose and swinging temperature gauge
- What you'll notice
- A thumping or hammering sound from the engine bay and a temperature gauge that moves up and down.
- Why it happens
- Ford issued bulletins for the 4.0L temperature gauge fluctuating with a thumping coolant hose. Consumer Guide notes the noise and erratic gauge come from a weak water pump; a revised pump was released.
- What to do
- Watch the gauge; if it heads toward hot, pull over. Have the cooling system checked for trapped air and a weak water pump.
Heater core leaks
- What you'll notice
- A sweet coolant smell inside, fog on the windshield, damp front carpet, or coolant level dropping.
- Why it happens
- Ford issued a bulletin for heater core leaks on these vans. Old coolant speeds up corrosion inside the core.
- What to do
- Check the coolant level and carpets. Heater core replacement is a large job; a shop may bypass the core temporarily so the engine doesn't lose coolant.
A/C compressor fails
- What you'll notice
- A/C blows warm, the compressor makes noise, or the compressor clutch won't engage.
- Why it happens
- Ford and Consumer Guide both note compressors on these vans fail when the system is low on refrigerant oil.
- What to do
- Have the system leak-checked first. If the compressor is replaced, the system should be flushed and the correct oil amount added.
Power steering pump leaks or loses assist
- What you'll notice
- Steering gets heavy, the pump whines, fluid leaks, or the pump pulley smokes.
- Why it happens
- Owners report power steering pump leaks and loss of assist. Low fluid lets the pump overheat.
- What to do
- Check the fluid level and look for the leak. Do not keep driving with the pump dry.
Rear brake drums stick or adjusters seize
- What you'll notice
- Scraping from the rear, a drum that won't come off at a brake job, uneven braking or a weak parking brake.
- Why it happens
- The rear drum brake self-adjusters wear and stick, which can leave the shoes dragging or out of adjustment.
- What to do
- Have the rear brakes cleaned and adjusted at each brake service. Replace the adjuster hardware if it is seized.
Check engine light with misfire codes
- What you'll notice
- Check engine light with codes P0300–P0306, sometimes with no running problem you can feel.
- Why it happens
- Ford released computer reprogramming for misfire codes on the 4.0L. Worn plugs, plug wires or a coil can also cause real misfires.
- What to do
- Have the codes read. If it runs smoothly, ask about the update. If it shakes or the light flashes, get it checked promptly to protect the catalytic converter.
Air switches to the defroster when accelerating
- What you'll notice
- Airflow moves from the dash vents to the windshield when you climb a hill or accelerate.
- Why it happens
- The vents are moved by engine vacuum. A leaking vacuum line or reservoir lets the doors fall back to defrost when vacuum drops, as described in a Ford bulletin.
- What to do
- Have the vacuum lines to the heater controls checked for cracks. This is usually an inexpensive fix.
Blower motor chirps or squeaks
- What you'll notice
- A chirp or squeak from behind the dash on low fan speeds.
- Why it happens
- Ford issued bulletins for blower motor squeaking at low speeds.
- What to do
- This is mostly an annoyance. A new blower motor fixes it if it bothers you.
Front axle oil leaks from the vent (AWD)
- What you'll notice
- Gear oil on the front differential or underbody of an all-wheel-drive van.
- Why it happens
- Ford issued bulletins for front drive axle fluid pushing out of the vent tube under some driving conditions.
- What to do
- Have the front axle fluid level checked and the vent tube rerouted per the bulletin. Low fluid can damage the front differential.
Rapping or clanging noise when steering
- What you'll notice
- A knock or clang from the steering when turning quickly or on rough roads.
- Why it happens
- Ford issued a bulletin for rapping or clanging noise from the steering on these vans.
- What to do
- Have the steering shaft and linkage checked for wear. Ask the shop about the Ford bulletin fix.
Shifter won't come out of Park or interlock acts up
- What you'll notice
- The shifter is stuck in Park, or it shifts out of Park without pressing the brake.
- Why it happens
- Ford issued bulletins about the brake shift interlock being disabled by brake light faults. A burned-out brake bulb or switch problem affects the interlock.
- What to do
- Check that the brake lights work. A brake switch or bulb is usually the fix.
Sliding door won't latch or close properly
- What you'll notice
- The sliding door takes several slams to close, won't latch, or rattles.
- Why it happens
- Ford issued a bulletin for damaged or misadjusted sliding door latches, and owners reported latch failures.
- What to do
- Have the latch and striker adjusted. A door that is not fully latched is a safety risk, especially with kids in back.
Battery drains while parked
- What you'll notice
- The battery is dead after the van sits for a day or two.
- Why it happens
- Ford issued bulletins on dead batteries from an intermittent electrical draw.
- What to do
- Have a shop measure the draw with everything off and pull fuses to find the circuit.
Buzzing or rattling from the exhaust
- What you'll notice
- A buzz or rattle from under the van at certain engine speeds.
- Why it happens
- Ford issued bulletins for buzzing or rattling noises from the exhaust, usually a loose heat shield.
- What to do
- Have the heat shields checked and clamped. It is not urgent unless a part is hanging.
Repair prices for your 1997 Ford Aerostar
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace automatic transmission with a rebuilt or used unit
- Replace a cracked wheel (used or aftermarket, each)
- Replace front wheel bearings and seal (one side)
- Replace rear axle bearing and seal (one side)
- Replace front brake pads and rotors
- Replace front calipers and flush brake fluid
- Diagnose rear ABS and replace speed sensor
- Replace rear brake shoes, drums and hardware
- Replace oil pan gasket
- Diagnose engine noise and check oil pressure
- Replace water pump and refill coolant
- Reprogram computer or replace plugs and wires
- Replace heater core
- Repair vacuum line or reservoir for climate controls
- Replace A/C compressor, drier and recharge
- Replace blower motor
- Reroute front axle vent and refill fluid
- Replace power steering pump
- Service or replace steering shaft/linkage part
- Replace brake light switch or bulb
- Adjust or replace sliding door latch
- Find parasitic draw and repair circuit
- Secure or replace exhaust heat shield
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Free dealer recall repairNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Checking the NHTSA recall database…