Your 2004 Ford Excursionproblems, repair costs and recalls
What we've documented about the 2004 Ford Excursion: problems owners and shops report, typical repair and upkeep costs, and safety recalls.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems for your 2004 Ford Excursion
10 documented issues apply to 2004, most serious first.
Coolant loss and white smoke from oil cooler or EGR cooler failure
- What you'll notice
- Coolant disappears with no puddle, white steam-like smoke comes from the tailpipe (worst at startup), coolant gets pushed out of the overflow (degas) bottle, or the engine runs hot when towing.
- Why it happens
- The 6.0L's engine oil cooler clogs on the coolant side, which starves the EGR cooler of coolant. The overheated EGR cooler then cracks and lets coolant into the exhaust or intake. Owners report very expensive repairs when it leads to head gasket damage.
- What to do
- Watch the coolant level and compare engine oil and coolant temperatures with a scan tool; a gap of more than about 15 degrees points to a clogged oil cooler. Fix it early, before it damages the head gaskets.
Head gaskets blow on the 6.0L diesel
- What you'll notice
- Coolant pushed out of the overflow bottle, bubbles in the coolant, white exhaust smoke, and overheating under load.
- Why it happens
- The 6.0L uses stretch-type head bolts that can give way under heat and high cylinder pressure, especially after an EGR cooler failure or with performance tuning.
- What to do
- Stop towing and have a cooling system pressure test done. The lasting fix is new head gaskets with stronger head studs, along with fixing whatever caused the overheating.
6.0L diesel won't start from a failing injector control module
- What you'll notice
- Hard starting or cranking with no start (often in cold weather), rough idle, misfiring and stalling.
- Why it happens
- The fuel injection control module (FICM) on top of the engine powers the injectors. Engine heat, vibration and weak batteries wear out its electronics until it can't fire the injectors properly.
- What to do
- Have the batteries tested first, then have a shop check the FICM output voltage. A rebuilt or upgraded FICM usually fixes the no-start.
6.0L diesel may stall without warning (recall)
- What you'll notice
- The engine dies while driving and may not restart.
- Why it happens
- Ford recalled 2004–2005 Excursions and other trucks with the 6.0L diesel because the engine could stall unexpectedly.
- What to do
- Ask the dealer to check your VIN for open recalls; the dealer repair is free.
Free at a Ford dealer if not already done. Ask the dealer to check your VIN for open recalls.
Automatic transmission overheats and fails
- What you'll notice
- Slipping, harsh or delayed shifts, a burnt fluid smell, or the transmission quitting altogether, especially when towing.
- Why it happens
- The 4R100 four-speed automatic in gas and 7.3L diesel Excursions runs hot when it hauls this much weight. Heat breaks down the fluid and wears out clutches. Owners report expensive repairs around 100,000 miles.
- What to do
- Change the transmission fluid and filter regularly, more often if you tow. If shifts slip, stop towing and see a transmission shop before the damage spreads.
Lights can fail from the steering column switch (recall)
- What you'll notice
- Headlights, turn signals or other exterior lights stop working.
- Why it happens
- Ford recalled these Excursions because the multifunction switch on the steering column could fail and leave lights not working.
- What to do
- Check your VIN for open recalls; the repair is free.
Free at a Ford dealer if not already done. Ask the dealer to check your VIN for open recalls.
6.0L diesel hard to start when hot from high-pressure oil leaks
- What you'll notice
- Long cranking, no start when the engine is hot, or stalling, sometimes with codes P2284, P2285 or P2290/P2291.
- Why it happens
- The 6.0L uses high-pressure engine oil to fire the injectors. Leaking O-rings at the oil rail plugs, standpipes or the pump fitting (STC fitting) let pressure bleed off, so the injectors can't fire.
- What to do
- Have a diesel shop read injection control pressure while cranking. Leaking fittings and O-rings are fixable without replacing the pump in many cases.
Turbo lag from sticking turbo vanes
- What you'll notice
- Slow response when you press the gas, low boost, or a sudden surge of power once the turbo catches up.
- Why it happens
- The 6.0L's variable-geometry turbo has vanes that stick from soot buildup, especially in trucks that do a lot of short trips and idling.
- What to do
- Regular highway driving with a few hard pulls helps keep vanes clean. If lag persists, a shop can clean the vanes and unison ring.
Rough cold running from sticking injectors (stiction)
- What you'll notice
- The engine runs rough, misses or smokes on cold starts, then smooths out as it warms up.
- Why it happens
- Deposits from engine oil make the 6.0L's oil-fired injectors stick internally. Long oil change intervals and poor oil make it worse.
- What to do
- Change the oil on time with the correct diesel oil. Additives can help mild cases; badly sticking injectors need replacing.
Power door locks stop working
- What you'll notice
- One or more doors won't lock or unlock with the switch or remote, the door makes a grinding noise, or the alarm acts up.
- Why it happens
- The door lock actuators wear out, or resistance builds up in the wiring.
- What to do
- Have the circuit tested first, then replace the bad actuator. Lock that door by hand until it's fixed.
Repair prices for your 2004 Ford Excursion
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace engine oil cooler and EGR cooler
- Replace head gaskets and install head studs
- Replace fuel injection control module (FICM)
- Reseal high-pressure oil rail plugs, standpipes or STC fitting
- Remove and clean turbo vanes, replace unison ring
- Treat with additive or replace sticking injectors
- Rebuild or replace 4R100 automatic transmission
- Replace door lock actuator (one door)
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Free dealer recall repairNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Checking the NHTSA recall database…