Ford F-150problems, repair costs and recalls
Problems reported across 1996–2026. Pick your model year below to see what applies to your vehicle.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems
38 documented issues across all years, most serious first.
Cruise control deactivation switch can catch fire (recall)
- What you'll notice
- Smoke or a burning smell from the engine bay near the brake master cylinder, sometimes even with the truck parked and turned off.
- Why it happens
- A pressure switch for the cruise control mounted on the brake system can leak brake fluid into its electrical side, overheat and start a fire. Ford recalled these trucks to disconnect or fuse the switch.
- What to do
- Check your VIN for open recalls right away. Until the recall work is done, park outside and away from buildings.
Spark plug blows out of the cylinder head
- What you'll notice
- A sudden loud pop from the engine, then a ticking or puffing sound, rough running, misfire and a check engine light. The ignition coil may be pushed up or broken.
- Why it happens
- The aluminum cylinder heads on these engines hold the spark plugs with only a few threads. Over time the threads can strip and cylinder pressure pushes the plug out.
- What to do
- Stop driving and have it towed or repaired soon. The head threads usually need a thread insert or a head replacement; a shop should check the other plugs are tight.
Cam phaser and timing chain rattle
- What you'll notice
- A ticking or diesel-like knock from the top of the engine, worst at idle or on a cold start, with rough idle, lost power and cam timing codes.
- Why it happens
- The variable cam timing phasers, their oil-fed solenoids and the chain tensioners and guides wear, especially with low oil pressure or skipped oil changes. Worn parts let timing slip.
- What to do
- Have the cause diagnosed soon rather than driving on it, since broken guides or a jumped chain can wreck the engine. Use the specified oil and change it on time.
Transmission may suddenly downshift into first gear (recall)
- What you'll notice
- A sudden hard downshift while moving, the rear wheels briefly locking or skidding, and a lurch that can make the truck hard to control.
- Why it happens
- A transmission speed sensor signal can drop out for a moment, and the computer reacts by commanding first gear at speed. Ford recalled these trucks for a software update.
- What to do
- Check your VIN for open recalls and get the free software update before driving much more. If it happens, steer straight and slow down gently.
Side doors may not latch or may open while driving (recall)
- What you'll notice
- A door that won't stay shut, a door-ajar warning that won't clear, or a door that pops open while driving.
- Why it happens
- A small spring part inside the side door latch can break, so the latch does not hold properly. Ford recalled these trucks to inspect and replace the latches.
- What to do
- Check your VIN for open recalls. If a door won't latch firmly, don't carry passengers on that side until it is repaired.
Seat belt pretensioners can start a fire in a crash (recall)
- What you'll notice
- Usually no warning ahead of time. After a collision that fires the seat belt pretensioners, smoke or flames may appear near the bottom of the door pillars.
- Why it happens
- When the front seat belt pretensioners fire they can throw off strong sparks that ignite nearby insulation and carpet. Ford recalled Regular Cab and SuperCrew trucks to add heat-resistant protection.
- What to do
- Check your VIN for open recalls and have the free repair done.
Parking brake may apply by itself (recall)
- What you'll notice
- A brake warning light, and the parking brake engaging on its own, sometimes while driving.
- Why it happens
- The wiring harness on the rear axle can rub on the axle housing until the wires short, which can trigger the electric parking brake. Ford recalled these trucks to protect or replace the harness.
- What to do
- Check your VIN for open recalls and get it repaired promptly. If the brake warning light comes on, have the truck inspected before regular driving.
Windshield wiper motor may stop working (recall)
- What you'll notice
- Front wipers that work only some of the time or stop completely.
- Why it happens
- The front wiper motor can fail. Ford recalled affected trucks to replace the motor.
- What to do
- Check your VIN for open recalls. Do not drive in rain or snow with wipers that are acting up.
Rear axle hub bolt can break (recall)
- What you'll notice
- Loss of drive power, clunking from the rear, or the truck rolling while in Park if the parking brake isn't set.
- Why it happens
- On trucks with the Max Trailer Tow package and heavy-duty rear axle, the bolt holding the axle hub can fatigue and break, damaging the splines that drive the wheel. Ford recalled these trucks to replace both rear axle shafts.
- What to do
- Check your VIN for open recalls. Always set the parking brake when parked until the repair is done, and stop towing if the rear end makes noise.
Brake master cylinder can leak fluid (recall)
- What you'll notice
- Red brake warning light, low brake fluid with no puddle under the truck, and a brake pedal that sinks or needs more effort.
- Why it happens
- The master cylinder on trucks with the 3.5L EcoBoost can leak brake fluid into the brake booster. That takes away braking from the front wheels. Ford recalled these trucks in two campaigns.
- What to do
- Do not ignore a brake warning light or a soft pedal. Have the truck checked right away and confirm the recall work was done.
Intake valves can break (recall)
- What you'll notice
- Sudden misfire, loss of power or an engine that quits and will not restart.
- Why it happens
- Intake valves in some 2.7L EcoBoost engines were made from a material that can crack and break. A broken valve can wreck the engine. Ford recalled affected trucks after a federal investigation.
- What to do
- Have a dealer check your VIN for this recall. If the engine starts running rough or loses power, stop driving and have it towed.
Fuel tank straps may not hold the tank (recall)
- What you'll notice
- Fuel smell, fuel dripping under the truck, or a tank that hangs low or rattles.
- Why it happens
- The straps that hold the fuel tank may not be secured properly. The tank can shift, leak or come loose. Ford recalled these trucks to inspect and replace the straps.
- What to do
- Check your VIN for this recall. If you smell fuel or see the tank sagging, stop driving and have the truck towed in.
Engine oil plug can leak quickly (recall)
- What you'll notice
- Oil warning light, a large oil leak under the engine, or a burning-oil smell.
- Why it happens
- A sealing plug in the 3.5L turbo engine may have been pressed in crooked. It can let oil out fast, which can damage the engine or start a fire if oil reaches hot parts. Ford recalled affected trucks to inspect and replace the plug.
- What to do
- If the oil light comes on or you see a big leak, shut the engine off and have the truck towed. Check your VIN for this recall.
Transmission valve body fault can cause loss of reverse (recall)
- What you'll notice
- Reverse does not engage, or the truck moves in a direction you did not expect.
- Why it happens
- The valve body inside the automatic transmission may have been machined incorrectly. Ford recalled affected trucks to replace it.
- What to do
- Check your VIN for this recall. If reverse acts up or the truck moves unexpectedly, park it and call the dealer.
Steering gear can bind or lock (recall)
- What you'll notice
- Steering that feels notchy, sticks or becomes very hard to turn.
- Why it happens
- Some steering gears were built with the wrong rack, which can crack the gear teeth inside. Ford recalled affected trucks to replace the steering gear.
- What to do
- Check your VIN for this recall. If the steering binds or feels wrong, do not drive the truck until it is inspected.
Tailgate cable can break and let the tailgate fall
- What you'll notice
- A snap or bang from the back of the truck, then the tailgate hangs crooked or drops onto the bumper, sometimes while loading or driving.
- Why it happens
- A support cable on the left side of the tailgate can fail, so the tailgate is no longer held level and can swing down on its own.
- What to do
- Do not carry anything on the tailgate and get the recall repair done right away, because a tailgate that drops while driving can spill cargo into traffic.
Front seat may not be bolted down properly
- What you'll notice
- The seat feels loose, shifts or rocks when you get in, brake or accelerate. Many trucks show nothing at all.
- Why it happens
- Some front seats left the factory without their mounting bolts tightened to spec, so the seat frame can move on its tracks.
- What to do
- Have the dealer inspect and tighten or replace the seat bolts before driving much further, because a loose seat badly affects how the belt and airbags protect you in a crash.
Wrong rear axle bearings can lock a rear wheel
- What you'll notice
- Growling or grinding from the rear axle that changes with speed, then a sudden grab, vibration or loss of drive.
- Why it happens
- Some trucks were built with the wrong rear axle tail bearings, which can come apart and either seize a wheel or let the driveshaft separate.
- What to do
- Stop driving the truck and have the recall inspection and bearing replacement done, because a rear wheel locking at speed can put you off the road.
Connecting rod or bearing defect can wreck the engine
- What you'll notice
- A deep knock that rises with engine speed, an oil pressure warning, metal flakes in the oil, then power loss or an engine that stops and will not restart.
- Why it happens
- Defective connecting rods and bearing parts from a supplier can wear through and let the rotating assembly come apart.
- What to do
- Stop driving and have the recall inspection done, because once the bearings fail the engine usually needs replacing.
Coolant hose can rub through the engine wiring
- What you'll notice
- The engine stalls without warning or will not restart, often with several warning lights, and the dash may show a wrench or powertrain message.
- Why it happens
- A coolant hose can rub against the engine wiring harness or pull on the engine computer connector pins, breaking the signals the engine needs to run.
- What to do
- Have the recall repair done promptly, since a stall in traffic or an intersection is dangerous.
Electronic brake booster can quit and leave a hard pedal
- What you'll notice
- A brake warning light or message, then a pedal that suddenly feels very hard and needs a lot more effort, with longer stopping distances.
- Why it happens
- The electronic brake booster can fail, so the truck falls back on your leg alone to build braking pressure.
- What to do
- Stop driving and have the booster recall work done; the brakes still work but need far more force than most drivers expect.
Spark plugs seize and break during removal
- What you'll notice
- Misfire or check engine light when plugs are due, and a shop warning that plugs may break or have broken off in the head during a tune-up.
- Why it happens
- The original two-piece plug design lets carbon build up on the lower shell so it sticks in the head and snaps when unscrewed. Ford issued service bulletins with a special removal procedure and tool, and a revised plug.
- What to do
- Have plugs replaced by a shop that knows this engine and uses Ford's removal procedure. Insist on the correct plug type to avoid spark knock.
EcoBoost stumble or power loss in damp weather
- What you'll notice
- Shaking, misfire or a sudden loss of power when accelerating hard or towing on humid or rainy days, sometimes with the engine going into reduced-power mode.
- Why it happens
- Water condenses inside the intercooler and gets pulled into the engine in a gulp under boost. Ford released service bulletins adding a deflector and updated engine software, and NHTSA opened an investigation.
- What to do
- Ask a Ford dealer whether the intercooler and software updates have been done on your truck.
Cam phaser rattle on cold start
- What you'll notice
- A loud rattle or clatter for a few seconds after starting a cold engine, sometimes with a check engine light for cam timing.
- Why it happens
- The cam phasers can lose their locked position while the engine sits, so they rattle until oil pressure builds. Ford issued service bulletins and a coverage program for phaser replacement.
- What to do
- Have a Ford dealer check whether your truck qualifies for the cam phaser program before paying for the repair.
10-speed automatic harsh or erratic shifting
- What you'll notice
- Hard or clunky shifts, slipping, delayed engagement, or the truck hunting between gears, especially at low speed.
- Why it happens
- Owners have reported rough shifting on the 10-speed automatic, and class action lawsuits were filed over it. Many cases improve with updated software and a relearn; some need internal repairs.
- What to do
- Ask the dealer to check for updated transmission software and perform an adaptive relearn first, and keep records of every visit.
Excessive oil consumption
- What you'll notice
- Oil level dropping fast between changes, a low-oil warning, blue smoke on startup, or misfires from fouled plugs.
- Why it happens
- Oil gets past the piston rings and is burned in the cylinders. Ford issued a service bulletin covering oil consumption on these engines, and owners filed lawsuits over it.
- What to do
- Check the oil level every fill-up and top up as needed. If it uses a lot, ask a dealer for an oil consumption test under the bulletin.
Inside door handle spring can break (recall)
- What you'll notice
- An inside door handle feels loose or does not spring back after you pull it.
- Why it happens
- A spring in the inside door handle can break. With the handle not returning fully, the door may not stay latched in a side crash. Ford recalled these trucks to inspect and repair the handles.
- What to do
- Have a Ford dealer run your VIN for this recall. If a handle feels loose, get it looked at soon.
Brake light switch may be out of adjustment (recall)
- What you'll notice
- The brake lights may stay on when your foot is off the pedal, or may not come on when you brake.
- Why it happens
- The stop lamp switch at the brake pedal may not have been adjusted correctly at the factory. Ford recalled affected trucks to check and reset it.
- What to do
- Ask someone to watch the brake lights while you press and release the pedal, and have a dealer check your VIN for this recall.
Timing chain stretch
- What you'll notice
- Check engine light, often with a short rattle from the front of the engine on a cold start.
- Why it happens
- The main timing chain on the early 3.5L EcoBoost can wear and lengthen, which throws cam timing off enough to set a code. Ford issued a service bulletin with an updated chain kit.
- What to do
- Have the code read and the chain checked before long. Keeping up with oil changes helps slow the wear.
Oil pan seal leak
- What you'll notice
- Oil drips under the engine or an oily film on the bottom of the oil pan.
- Why it happens
- The sealant between the plastic oil pan and the engine can let go on the 2.7L EcoBoost. Ford issued a service bulletin calling for a new, revised pan.
- What to do
- Check the oil level regularly and have the leak confirmed and repaired at your next visit.
Backup camera image can freeze or go blank (recall)
- What you'll notice
- The screen shows a frozen, delayed or blank picture when you shift into reverse.
- Why it happens
- A software fault in the screen module can stop the rear camera image from showing correctly. Ford recalled these trucks for a software update that can be done at the dealer or over the air.
- What to do
- Check your VIN for this recall and get the update. Until then, use your mirrors and look behind you when backing up.
Trailer brake and lights can stop working (recall)
- What you'll notice
- Trailer warning messages on the dash, or trailer brakes and turn signals that quit while towing.
- Why it happens
- The built-in trailer module can lose communication with the truck. Ford recalled these trucks for a software update.
- What to do
- If you tow, have the recall update done before your next trip and check the trailer lights and brakes each time you hook up.
Windshield may not be bonded properly (recall)
- What you'll notice
- Usually nothing you can see. Some owners may notice wind noise or a water leak around the glass.
- Why it happens
- The windshield adhesive may not have bonded correctly at the factory, so the glass could come out in a crash. Ford recalled affected trucks to remove and reinstall the windshield.
- What to do
- Have a dealer check your VIN for this recall and get the windshield rebonded.
Speedometer and tachometer needles can stick
- What you'll notice
- The needles hang in one place, jump around or read nothing while the truck is clearly moving or revving.
- Why it happens
- A fault inside the analog instrument cluster keeps the gauge motors from following the signals they are sent.
- What to do
- Get the cluster replaced under the recall; until then watch your speed another way, since a stuck speedometer is easy to get a ticket with.
Rear stabilizer bar fasteners may be loose
- What you'll notice
- A clunk or rattle from the back of the truck over bumps, and the rear may feel loose when cornering with a load.
- Why it happens
- The fasteners holding the rear stabilizer rod were not tightened enough on the line and can work their way loose.
- What to do
- Have the recall fastener replacement done soon; a stabilizer rod that comes free changes how the truck handles.
Door window drops into the door when the regulator breaks
- What you'll notice
- A crunch or a sharp pop from inside the door, then the glass slides down and will not come back up. On some trucks the window keeps travelling down after the switch is released.
- Why it happens
- The window regulator pulls the glass with a thin cable running over plastic guides. The cable frays and snaps or the plastic breaks, so nothing holds the glass. The switch and the motor are usually fine.
- What to do
- Have the regulator replaced before rain or a car wash soaks the interior, and treat the truck as unsecured until then. It is not dangerous to drive, but a window that falls on the highway is a theft and weather problem.
Heater core leaks coolant inside the cab
- What you'll notice
- A sweet smell in the cab, an oily film or fog on the inside of the windshield that wipes away and comes back, damp carpet on the passenger side, and weak or no heat.
- Why it happens
- The small heater radiator buried behind the dash corrodes from the inside and starts weeping coolant into the cabin instead of into the engine bay.
- What to do
- Get it replaced and the cooling system refilled. Until then watch the coolant level, because a truck that quietly loses coolant can overheat and damage the engine.
Camera menu can cover the backup camera image (recall)
- What you'll notice
- When shifting into Reverse, a camera-views menu stays on the center screen and partly blocks the rear camera picture.
- Why it happens
- Infotainment software on trucks with the 8-inch screen does not always close the camera menu when Reverse is selected. Ford is updating the software over the air or at a dealer.
- What to do
- Check your VIN for open recalls and accept the software update. Close the menu by hand and use your mirrors until then.
Repair prices for your Ford F-150
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Disconnect or replace switch and add fused jumper harness
- Repair spark plug threads with an insert and replace plug and coil
- Replace spark plugs and extract broken plugs
- Replace cam phasers, timing chains, guides and tensioners
- Reprogram powertrain computer
- Replace charge air cooler and update engine software
- Replace door latch
- Remove B-pillar insulation and add heat shield
- Replace cam phasers and timing chain kit
- Update transmission software and run adaptive relearn
- Repair or replace rear parking brake wiring harness
- Replace front wiper motor
- Replace rear axle hub bolts
- Update camera and display software
- Inspect and replace inside door handle
- Adjust or replace brake light switch
- Replace timing chain, guides, tensioner and phasers
- Replace brake master cylinder (and booster if contaminated)
- Replace engine oil pan
- Replace engine (long block) after valve failure
- Update screen module software
- Update trailer module software
- Inspect and replace fuel tank straps
- Inspect and replace engine oil gallery plug
- Replace transmission main control valve body
- Replace steering gear assembly
- Remove and reinstall windshield
- Replace tailgate support cables
- Inspect and retighten or replace front seat bolts
- Replace instrument cluster
- Replace rear axle shafts and bearings
- Replace rear stabilizer rod fasteners
- Replace engine long block
- Reroute coolant hose and repair engine harness
- Replace electronic brake booster
- Replace front door window regulator
- Replace heater core
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Pick a model year to see its safety recalls.