GMC Safariproblems, repair costs and recalls
Problems reported across 1996–2005. Pick your model year below to see what applies to your vehicle.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems
27 documented issues across all years, most serious first.
Automatic transmission slips, shifts hard or fails
- What you'll notice
- Late or harsh shifts, the engine revving up between gears, slipping when warm, or the van losing reverse, second or overdrive. In the worst cases it will not move at all.
- Why it happens
- The 4L60-E four-speed automatic behind the 4.3L works hard moving a heavy van, and heat breaks down the fluid and wears clutches and internal parts such as the sun gear shell. Transmission failure is the most costly problem owners report for these vans.
- What to do
- Check the fluid level and smell with the engine warm. Dark or burnt fluid is a bad sign. If it slips or will not engage, stop towing or loading the van and get a transmission diagnosis; a rebuild or a replacement unit is usually needed. An add-on transmission cooler helps a rebuilt unit last.
ABS kicks in at low speed and the van rolls farther
- What you'll notice
- When slowing to a stop, usually under about 5 mph on dry pavement, the pedal pulses and buzzes as if on ice and the van keeps rolling. Stopping distances get longer and the ABS light may come on.
- Why it happens
- Rust builds up on the front wheel speed sensors and the toothed rings they read. The weak or uneven signal makes the ABS computer think a wheel is locking, so it lets off brake pressure when it should not. Owners report it widely on these vans.
- What to do
- Leave extra room when stopping and get it checked soon. A shop can clean the sensor mounting areas and replace corroded sensors; if that does not cure it, the ABS module may be at fault. Do not simply pull the ABS fuse as a permanent fix.
Rusted brake and fuel lines leak
- What you'll notice
- The brake pedal suddenly sinks toward the floor, brake fluid drips near a wheel, or you smell raw fuel around the van. A brake warning light may come on.
- Why it happens
- The steel brake and fuel lines run along the underside and rust through with age, especially where roads are salted. Lines can also wear through where they rub on other parts.
- What to do
- If the pedal goes soft or you smell fuel, stop driving and have it towed. Ask the shop to check every brake and fuel line, not just the one leaking, because the rest are usually in similar shape.
Battery cable or wiring rubbed through by steering parts
- What you'll notice
- A dead battery or no-start, sparks or a burning smell, everything electrical cutting out while driving, or the brake pedal sinking after a sharp turn. In some cases a fire started.
- Why it happens
- The positive battery cable and a wiring harness near the front passenger wheel can rub against the steering linkage and suspension as the wheels turn. Once the insulation wears through, the wire shorts to the frame, which can melt nearby brake lines or damage the engine and ABS computers.
- What to do
- Look along the battery cable and nearby wiring for shiny worn spots, melted insulation or rub marks. Have damaged wires replaced and secured with proper clips away from moving parts before they short.
Brake lights and hazards can stop working (recall)
- What you'll notice
- The brake lights and rear hazard lights do not come on, and the hazard switch button may be stuck.
- Why it happens
- The hazard switch inside the multifunction switch on the steering column can wear its contacts and open the circuit for both the brake lights and the hazards. NHTSA looked into it and GM recalled 2001 and early 2002 Safari and Astro vans (recall 05V-099).
- What to do
- Have a helper check your brake lights. Ask a dealer whether recall 05V-099 was done; the fix is a new hazard switch with special grease, or a new multifunction switch.
Intake manifold gaskets leak coolant
- What you'll notice
- Coolant puddles on top of the engine where the intake meets the cylinder heads, a sweet smell, a falling coolant level, or overheating. Coolant mixing into the oil can turn it milky.
- Why it happens
- The 4.3L V6 uses intake gaskets that break down over time, which owners often link to the original Dex-Cool coolant. Coolant then seeps out of the joint, usually on the driver side.
- What to do
- Top up the coolant and watch the level and temperature gauge. Get it fixed soon, because coolant in the oil or overheating can ruin the engine. The fix is new upper and lower intake gaskets and fresh coolant.
Power steering failure also cuts brake assist
- What you'll notice
- Steering suddenly turns heavy and the brake pedal becomes very hard at the same moment, sometimes after a whine or squeal from the engine.
- Why it happens
- These vans use the power steering pump to power the brake booster. If the pump fails, leaks, or its belt or idler pulley lets go, you lose both power steering and power brakes together.
- What to do
- Pull over carefully. Press the brake harder than usual; the brakes still work, just without help. Have the pump, hoses, belt and pulleys checked before driving again.
Engine stalls while driving
- What you'll notice
- The engine dies while driving or pulling away, sometimes with the battery light on, and may not restart for a while. Steering and braking get much harder.
- Why it happens
- Owners trace it to several causes, including a failed crankshaft position sensor, a weak fuel pump and bad electrical connections. The cause has to be found with testing.
- What to do
- Get the van off the road safely and have it checked while the problem is happening if you can. Stored codes and a fuel pressure test help pin it down.
Gas pedal sticks or the van keeps accelerating
- What you'll notice
- The pedal feels jerky or sticks, the engine stays at high revs after you lift off, or cruise control does not let go when you brake.
- Why it happens
- A worn or fraying accelerator cable can bind or break, and dirty throttle parts can stick. Some owners also report cruise control that would not shut off.
- What to do
- If it happens, shift to neutral, brake firmly and turn off the engine once stopped. Have the throttle cable, throttle body and cruise control parts inspected and replaced as needed.
Low oil pressure and failed main bearings
- What you'll notice
- The oil pressure gauge drops or the oil light comes on, followed by knocking from the bottom of the engine.
- Why it happens
- A few owners of early vans report main bearing failure in the 4.3L that ended in an engine replacement.
- What to do
- If oil pressure drops, stop the engine right away and check the oil level. Have the pressure tested with a gauge, because the dash sender can also fail.
Steering knuckle can separate from worn lower ball joint (recall)
- What you'll notice
- A popping or clunking noise from the front when turning or backing up.
- Why it happens
- The rubber boot on the lower ball joint can rub on the steering knuckle and tear. Dirt and water then wear out the joint, and in the worst case the knuckle can separate, letting the wheel fold under and cutting the brake hose. GM recall 03044 (NHTSA 03V-328).
- What to do
- Ask a dealer whether the recall was done; the fix is new steering knuckles on both sides. If you still hear popping afterwards, have the ball joints inspected.
Windshield wipers work on and off or quit (recall)
- What you'll notice
- The wipers stop or work only sometimes, which is dangerous in rain or snow.
- Why it happens
- Solder joints on the circuit board inside the wiper motor crack. GM recalled these vans (recall 03V-159).
- What to do
- Check with a dealer that the recall was done. The fix is a new wiper motor circuit board and cover at no charge.
Rear bucket seat belt can tear in a crash (recall)
- What you'll notice
- No warning; the right rear bucket seat belt may not hold in a crash.
- Why it happens
- The webbing for the outer belt on the right rear bucket seat could separate in a crash (recall 97V-057).
- What to do
- Ask a dealer whether the recall was done on your van.
Engine overheats
- What you'll notice
- The temperature gauge climbs, steam or a coolant smell comes from under the van, or the low coolant light comes on.
- Why it happens
- Overheating is the top reported problem for the 2002 Safari. On this engine it usually follows coolant loss from leaking intake gaskets, a failing water pump or a blocked radiator.
- What to do
- Stop and let the engine cool if the gauge goes high. Have the cooling system pressure-tested to find the leak before the head gaskets are damaged.
Slipping when hot and code P1870 from a worn valve body
- What you'll notice
- The transmission feels like it slips or flares once it is fully warm, often after a long drive, and shifts can turn firm. The check engine light may come on with code P1870 (torque converter clutch slip).
- Why it happens
- Wear inside the aluminum valve body, the part that routes fluid to the clutches, lets pressure leak away. Owners and shops tie this to code P1870 on the 4L60-E, and GM later revised the design.
- What to do
- Have the code read and the fluid checked. Catching it early can mean replacing the valve body and related valves instead of rebuilding the whole transmission.
ABS warning light from a failed ABS control module
- What you'll notice
- The ABS light stays on. Anti-lock braking is switched off, and some owners notice odd pulsing or a hard pedal before the light comes on.
- Why it happens
- The electronic brake control module that runs the anti-lock system fails with age, often well past 100,000 miles. RepairPal has dozens of reports on these vans.
- What to do
- Normal brakes still work, but drive gently and have the ABS codes read. Rule out a cheaper wheel speed sensor problem first, then replace or rebuild the module.
Brake lights fail from a worn turn signal switch
- What you'll notice
- Brake lights, turn signals or hazards stop working, sometimes on and off.
- Why it happens
- The brake light circuit runs through the turn signal (multifunction) switch on the steering column. Its contacts wear, and these earlier vans were not part of the later recall on the same part.
- What to do
- Check the brake lights and signals. A shop can test the switch and replace it if the circuit is open there.
Rough running from the central 'spider' fuel injector
- What you'll notice
- Rough idle, hesitation, misfires and a check engine light that keep coming back, even after new plugs and wires. Fuel economy drops.
- Why it happens
- The 4.3L uses one central injector unit with lines and small poppet nozzles feeding each cylinder. The nozzles stick or clog and the unit can leak, so cylinders get the wrong amount of fuel.
- What to do
- Have the misfire codes read and a fuel pressure and injector test done. Replacing the central injector assembly usually cures it; a leaking unit is also a fire risk, so do not put it off.
Misfires from worn ignition parts or vacuum leaks
- What you'll notice
- Jerking at highway speed, a shaky idle, and a check engine light with code P0300 or a single-cylinder misfire code.
- Why it happens
- The 4.3L fires its plugs through a distributor cap, rotor and long plug wires that wear out, and aging vacuum hoses split and let in extra air. Owners often find more than one of these at once.
- What to do
- Have the codes read. Replace the cap, rotor, wires and plugs as a set if they are old, and check the vacuum hoses for cracks. Do not keep driving with a flashing check engine light, since it can overheat the catalytic converter.
Fuel pump fails and the engine stalls or won't start
- What you'll notice
- The engine cranks but will not start, or it cuts out while driving and may restart later. You may not hear the pump hum when you turn the key.
- Why it happens
- The electric pump inside the fuel tank wears out, and some owners have replaced it more than once.
- What to do
- Have fuel pressure tested to confirm the pump is the cause. Replace the fuel filter at the same time. The tank has to come down, so this is not a quick job.
Dashboard gauges stop working or read wrong
- What you'll notice
- The speedometer, fuel gauge or other gauges freeze, drop to zero or show wrong readings, sometimes along with the odometer.
- Why it happens
- The instrument cluster develops faults with age, often in the small gauge motors or the circuit board.
- What to do
- Do not rely on the fuel gauge until it is fixed. A shop that rebuilds instrument clusters can usually repair the original.
Brake shudder from warped front rotors
- What you'll notice
- A shaking steering wheel or pulsing pedal when braking, a thumping noise from the front, or the van pulling to one side.
- Why it happens
- Front brake rotors on this heavy van warp from heat, and some owners report replacing them repeatedly.
- What to do
- Have the rotors measured. Replace them with quality parts and tighten the wheels to the correct torque, which helps prevent warping.
Built-in child seat belt can lock up (recall)
- What you'll notice
- The harness on the built-in child seat stays locked and will not pull out.
- Why it happens
- Some integrated child seats were missing small springs in the belt retractor, so the belt can lock in the stowed position and be unusable (recall 99V-009).
- What to do
- If your van has the built-in child seat, ask a dealer whether the recall was done and do not use a seat that will not adjust.
Won't start after damp, cold weather from a wet distributor cap
- What you'll notice
- The engine cranks but will not start after the van sits in cold, wet or icy weather. A new battery does not help.
- Why it happens
- Moisture can collect inside the distributor cap, so the spark leaks away before it reaches the plugs.
- What to do
- Have the cap and rotor checked. Replacing them, and making sure the cap seals well, usually ends the problem.
Power door locks stop working
- What you'll notice
- One or more doors will not lock or unlock with the switch or remote, or a lock clicks without moving.
- Why it happens
- The electric lock actuator inside the door wears out. It is one of the most reported problems on RepairPal for these vans.
- What to do
- Test each door to find which actuator has failed. Replacing the actuator inside the door panel usually fixes it.
Outside door handles break
- What you'll notice
- A door handle feels loose or snaps, and the door will not open from outside.
- Why it happens
- The plastic outside handles crack with age and use. RepairPal has more than 100 owner reports, on every door.
- What to do
- Replace the handle before it fails completely. On the sliding door, a broken handle can leave passengers unable to get out from the outside.
Power windows stop going up
- What you'll notice
- A window goes down but will not come back up, moves slowly, or makes grinding noises.
- Why it happens
- The window motor or regulator inside the door wears out, and some owners have replaced them more than once.
- What to do
- Have the motor and regulator checked. Many shops replace them together because they wear at the same time.
Repair prices for your GMC Safari
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Rebuild or replace 4L60-E automatic transmission
- Replace transmission valve body and related valves
- ABS diagnosis; clean mounts and replace front wheel speed sensors
- Replace or rebuild ABS electronic brake control module
- Replace and re-route positive battery cable
- Replace turn signal (multifunction) switch
- Replace upper and lower intake manifold gaskets and coolant
- Replace central (spider) fuel injector assembly
- Replace distributor cap, rotor, spark plug wires and spark plugs
- Replace distributor cap and rotor
- Replace in-tank fuel pump module and fuel filter
- Replace power steering pump
- Replace engine with a remanufactured 4.3L V6
- Replace power door lock actuator (one door)
- Replace outside door handle (one door)
- Replace window motor and regulator (one door)
- Replace front brake pads and rotors
- Replace water pump and coolant (most common fix after leak testing)
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Replace hazard switch or multifunction switch (recall 05V-099)No charge if your vehicle is included
- Replace both front steering knuckles (recall 03V-328)No charge if your vehicle is included
- Replace wiper motor circuit board and cover (recall 03V-159)No charge if your vehicle is included
- Seat belt repair (recall 97V-057)No charge if your vehicle is included
- Integrated child seat belt repair (recall 99V-009)No charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Pick a model year to see its safety recalls.