Jeep Cherokeeproblems, repair costs and recalls
Problems reported across 1996–2023. Pick your model year below to see what applies to your vehicle. Not sold 2002-2013 (replaced by the Liberty).
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems
30 documented issues across all years, most serious first.
Cracked cylinder head (0331 casting)
- What you'll notice
- Coolant keeps disappearing with no visible leak, overheating, white exhaust smoke, or milky oil.
- Why it happens
- Late XJs used a head casting marked 0331 that is prone to cracking, especially after the engine runs hot, letting coolant seep into the cylinders or oil.
- What to do
- Stop driving if it overheats. Have a cooling-system pressure test and combustion-gas test done, and if the head is cracked replace it with an updated casting.
Transmission may shift to neutral without warning (recall)
- What you'll notice
- The SUV suddenly loses drive while moving, as if it slipped into neutral, sometimes with a warning message.
- Why it happens
- A wiring problem in the 9-speed transmission's range sensor circuit could make the computer select neutral. Jeep recalled these years, and 2014 V6 models got a later software recall as well.
- What to do
- Check the VIN for open recalls right away and have them done before relying on the vehicle in traffic.
4x4 power transfer unit failure (recalls)
- What you'll notice
- Sudden loss of drive, grinding or clunking from underneath, a 4WD warning, or the vehicle rolling while the shifter is in Park.
- Why it happens
- Parts inside the power transfer unit can wear or break and disconnect the wheels from the transmission. Several recalls cover different build ranges.
- What to do
- Check the VIN for open recalls now and always set the parking brake when parked until the unit is inspected.
Cracked oil pump housing (recall)
- What you'll notice
- Oil pressure warning, engine noise, or the engine shutting off while driving.
- Why it happens
- The oil pump housing on some engines could crack, cutting off oil pressure. Jeep recalled affected vehicles.
- What to do
- Check the VIN for open recalls. If the oil pressure light comes on, pull over and shut the engine off.
Steering gear may break (recall)
- What you'll notice
- Clunking or loose feel in the steering, or a sudden loss of steering control.
- Why it happens
- A gear inside the steering rack on some vehicles could break. Jeep recalled affected SUVs for inspection and repair.
- What to do
- Check the VIN for open recalls and have it fixed before regular driving. Any odd steering feel needs prompt attention.
Side air bags may deploy unexpectedly (recall)
- What you'll notice
- The airbag warning light may be on, or the side curtain and seat airbags go off without a crash.
- Why it happens
- A problem with the side impact sensing on vehicles built from early 2013 through late 2014 could fire the side airbags without a collision. Jeep recalled them.
- What to do
- Check the VIN for open recalls and get the remedy done. Have any airbag warning light looked at promptly.
Done free under recall 15V-041. Check your VIN with a Jeep dealer.
Power liftgate module can short and catch fire (recall 23V-338)
- What you'll notice
- A power liftgate that stops working or acts up, a burning smell or smoke from the rear cargo area, even with the vehicle parked and switched off.
- Why it happens
- Water can get into the power liftgate control module and its connectors and cause a short circuit. Earlier recall repairs did not fully cure it, so Jeep issued a newer recall that moves the module and adds a water shield.
- What to do
- Check the VIN for this recall right away. Until the repair is done, park outside and away from buildings.
Done free under recall 23V-338. Check your VIN with a Jeep dealer.
Cruise control may not switch off (recall 18V-332)
- What you'll notice
- Cruise control keeps holding speed, or the vehicle keeps accelerating, after you tap the brake or press cancel.
- Why it happens
- If a certain short circuit happens in the vehicle network while the cruise control is speeding up, the system may not let go. Jeep recalled these years for a software update.
- What to do
- Check the VIN for this recall and do not use cruise control until the update is done. If it ever sticks, brake firmly and shift to Neutral.
Done free under recall 18V-332. Check your VIN with a Jeep dealer.
Front axle shaft may break (recalls 16V-284, 16V-287)
- What you'll notice
- A sudden loss of drive with no warning, and the vehicle may roll when parked if the parking brake is not set.
- Why it happens
- Some left and right front half-shafts were not made to specification and can fracture.
- What to do
- Check the VIN for these recalls and have the affected shaft replaced. Use the parking brake every time you park until then.
Done free under recall 16V-284, 16V-287. Check your VIN with a Jeep dealer.
Transmission software may stall the engine (recall 18V-739)
- What you'll notice
- The engine stalls, usually while slowing down or at low speed.
- Why it happens
- The transmission computer on 2.4L models was programmed with a calibration that can let the engine stall.
- What to do
- Check the VIN for this recall and have the transmission software updated before relying on the vehicle in traffic.
Done free under recall 18V-739. Check your VIN with a Jeep dealer.
Missing valve parts can damage the engine (recall 18V-344)
- What you'll notice
- Ticking or knocking from the top of the engine, a misfire, a check engine light or sudden loss of power.
- Why it happens
- Some early 2.0L turbo engines were assembled without small retainers on the valve stems or with a camshaft cap fitted backwards, which can damage the valves and camshaft.
- What to do
- Check the VIN for this recall. If the engine starts knocking or misfiring, stop driving and have it towed to a dealer.
Done free under recall 18V-344. Check your VIN with a Jeep dealer.
Reduced rear braking (recall 18V-523)
- What you'll notice
- A soft or low brake pedal and longer stopping distances.
- Why it happens
- Rear brake caliper pistons may have a faulty coating that lets gas pockets form in the brake fluid.
- What to do
- Check the VIN for this recall and have the brakes bled by a dealer. Do not ignore a soft pedal.
Done free under recall 18V-523. Check your VIN with a Jeep dealer.
Engine computer chip failure (recall 18V-524)
- What you'll notice
- The engine stalls while driving or will not start, often with warning lights.
- Why it happens
- A voltage regulator chip inside the powertrain control module could fail.
- What to do
- Check the VIN for this recall and have the module replaced. Do not rely on the vehicle in traffic if it has stalled.
Done free under recall 18V-524. Check your VIN with a Jeep dealer.
Fuel tube may leak under the hood (recall 18V-282)
- What you'll notice
- A fuel smell from the engine bay or wetness around the fuel line.
- Why it happens
- A fuel tube on some 2.4L engines can leak fuel into the engine compartment, which is a fire risk.
- What to do
- Stop driving if you smell fuel and check the VIN for this recall.
Done free under recall 18V-282. Check your VIN with a Jeep dealer.
Front lower control arm may break (recall 20V-657)
- What you'll notice
- A bang or clunk from a front corner, a wheel sitting out of line, or sudden loss of steering control.
- Why it happens
- Some front lower control arms were not made correctly and can fracture while driving.
- What to do
- Check the VIN for this recall. Jeep advised owners of affected vehicles not to drive until the arms are inspected.
Done free under recall 20V-657. Check your VIN with a Jeep dealer.
Transmission cooler hose may leak (recall 21V-310)
- What you'll notice
- Red fluid under the front of the vehicle, a burning smell, or slipping as the fluid level drops.
- Why it happens
- A transmission oil cooler hose may not have been cured properly when made and can leak fluid near hot parts, which is a fire risk.
- What to do
- Check the VIN for this recall. Stop and shut the engine off if you see smoke or smell burning fluid.
Done free under recall 21V-310. Check your VIN with a Jeep dealer.
Intermittent no-crank, no-start with limp mode and several warning lights
- What you'll notice
- Now and then the engine will not crank when you try to start it. Other times it runs but drops into a reduced-power limp mode with several warning lights on at once.
- Why it happens
- Jeep issued a service bulletin for 2023 Cherokees describing this pattern in the ignition and electrical system, with multiple stored trouble codes. The exact fix depends on what the dealer finds under that bulletin.
- What to do
- If it goes into limp mode, slow down and get somewhere safe. Have a Jeep dealer read the codes and check service bulletin S2308000032, while the truck is likely still under warranty.
Crankshaft position sensor failure
- What you'll notice
- The engine cranks but will not fire, or it quits once fully warm and only restarts after it cools off.
- Why it happens
- The sensor sits next to the bell housing where it takes a lot of engine heat, and over time it stops sending a clean signal, so the computer cuts spark.
- What to do
- Have the sensor and its wiring tested and replace the sensor if it is weak. It is one of the most common no-start causes on the XJ.
Rust in floor pans and frame rails
- What you'll notice
- Wet carpets, holes in the floor, or rot along the rocker panels and the rails under the body.
- Why it happens
- The XJ has a unibody, so the floor and rails carry the load. Salt and trapped water eat through them over the years.
- What to do
- Look underneath carefully, especially before buying. Rust in structural areas needs welded repair, not a cosmetic patch.
Rough, delayed or erratic shifting from the 9-speed automatic
- What you'll notice
- Harsh or late shifts, hesitation pulling away, lurching at low speed, or hunting between gears.
- Why it happens
- The early 9-speed automatic had software and calibration problems. Jeep released several control-module updates, which helped some vehicles more than others.
- What to do
- Ask the dealer whether the latest transmission software is installed and check the VIN for open recalls.
Excessive oil consumption
- What you'll notice
- The oil level drops between changes, the low oil light comes on, or the engine stalls, often in turns when the oil is low.
- Why it happens
- The piston oil control rings on this engine can wear and let oil burn off. Jeep ran an oil consumption test program and a class-action settlement extended coverage on many earlier-built engines.
- What to do
- Check the oil at every fill-up and top it off. Ask a dealer for an oil consumption test and whether your VIN has extended coverage.
Instrument cluster may go blank (recall 18V-917)
- What you'll notice
- Gauges, warning lights, messages or chimes do not come on.
- Why it happens
- The instrument cluster on some early 2019 builds can fail, so warnings may not reach the driver.
- What to do
- Check the VIN for this recall and have the cluster inspected or replaced soon.
Done free under recall 18V-917. Check your VIN with a Jeep dealer.
Right side curtain airbag connector may be loose (recall 24V-516)
- What you'll notice
- Usually nothing, though an airbag warning light may come on.
- Why it happens
- The electrical connector for the right-side curtain airbag may not have been secured properly, so the airbag might not deploy as intended.
- What to do
- Check the VIN for this recall and have the dealer secure the connector soon.
Done free under recall 24V-516. Check your VIN with a Jeep dealer.
Backup camera picture stays on after reverse (recall)
- What you'll notice
- The rear camera view stays up on the radio screen after you shift out of reverse and drive away, hiding the radio and navigation.
- Why it happens
- A software fault in the radio display leaves the camera image on screen instead of switching back, which pulls the driver's eyes off the road.
- What to do
- Have the radio software updated. It is free under the recall and on many cars can be done over the air.
Done free under recall 20V-191. Check your VIN with a Jeep dealer.
Battery or start-stop charging warning from the battery sensor
- What you'll notice
- A battery or charging warning light, a start-stop system message, or a battery charging alert on the dash, sometimes with the auto start-stop feature switching itself off.
- Why it happens
- The truck uses a small sensor on the battery cable (the intelligent battery sensor) to judge how charged the battery is. Jeep issued a service bulletin for 2023 Cherokees where this sensor reports the charge level wrongly and sets battery-related trouble codes.
- What to do
- Have the battery and charging system tested and ask a Jeep dealer to check service bulletin S1408000384. A weak battery is still possible, so do not ignore slow cranking or dimming lights.
Rear main seal and oil filter adapter leaks
- What you'll notice
- Oil drips where the engine bolts to the transmission, or an oily film along the bottom of the engine.
- Why it happens
- The rear main seal seeps with age. The gaskets at the oil filter adapter and the valve cover also leak and are easily mistaken for a main seal leak.
- What to do
- Rule out the cheaper filter adapter and valve cover gaskets first. Watch the oil level and fix bigger leaks before oil reaches the exhaust.
Cracked exhaust manifold
- What you'll notice
- A ticking or puffing sound from the engine bay, loudest when cold or under throttle, sometimes with an exhaust smell or a little less power.
- Why it happens
- The factory manifold flexes through many heat cycles and the welded joints split over time.
- What to do
- Have it checked for cracks and replaced with an updated manifold and a good gasket. Do not let exhaust fumes reach the cabin.
Power window switch and regulator failures
- What you'll notice
- One or more windows stop moving, only the driver's switch works, or the door locks act up.
- Why it happens
- The driver's master switch and the window regulators wear out on the later XJ.
- What to do
- Have the master switch tested first, then the regulator and motor for the affected window.
Side-to-side wobble when accelerating slowly
- What you'll notice
- A lateral shake or wobble felt at low speed while gently accelerating.
- Why it happens
- Jeep traced this to the front half-shafts and issued a bulletin that calls for inspecting and possibly replacing both of them.
- What to do
- Have a dealer check whether the bulletin applies to your vehicle and inspect the front axle shafts.
Turn signal cancels on its own (recall)
- What you'll notice
- The turn signal shuts off by itself before you turn the steering wheel.
- Why it happens
- The steering column control module could cancel the signal without input, which does not meet federal standards. Jeep recalled these SUVs.
- What to do
- Check the VIN for open recalls and have the column module inspected or replaced.
Done free under recall 24V-239. Check your VIN with a Jeep dealer.
Repair prices for your Jeep Cherokee
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace crankshaft position sensor
- Replace rear main seal (and oil pan gasket)
- Replace exhaust manifold
- Replace cylinder head with updated casting
- Replace front window regulator
- Update transmission software and relearn shifts
- Update transmission control software
- Replace power transfer unit (PTU)
- Replace engine oil pump
- Replace electric power steering gear
- Replace front axle half shafts
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Reflash occupant restraint control moduleNo charge if your vehicle is included
- Recall repair of turn signal / steering column switchNo charge if your vehicle is included
- Relocate liftgate module and add water shieldNo charge if your vehicle is included
- Update engine computer softwareNo charge if your vehicle is included
- Replace front half-shaftNo charge if your vehicle is included
- Re-flash transmission control moduleNo charge if your vehicle is included
- Inspect and repair or replace affected engine partsNo charge if your vehicle is included
- Replace instrument clusterNo charge if your vehicle is included
- Bleed brake systemNo charge if your vehicle is included
- Replace powertrain control moduleNo charge if your vehicle is included
- Replace engine fuel supply tubeNo charge if your vehicle is included
- Replace front lower control armsNo charge if your vehicle is included
- Replace transmission oil cooler hoseNo charge if your vehicle is included
- Secure curtain airbag connectorNo charge if your vehicle is included
- Update radio display softwareNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Pick a model year to see its safety recalls.