Jeep Compassproblems, repair costs and recalls
Problems reported across 2007–2026. Pick your model year below to see what applies to your vehicle.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems
31 documented issues across all years, most serious first.
ABS may lock the rear brakes (recall)
- What you'll notice
- The rear wheels lock up or skid during hard or slippery-road braking.
- Why it happens
- Software in the anti-lock brake control unit could let the rear brakes lock instead of modulating them.
- What to do
- Check your VIN for recall 06V-493 and have the ABS unit reprogrammed. Brake gently and leave extra distance until it is done.
Covered free under recall 06V-493. Check your VIN or ask a Jeep dealer.
Sticking accelerator pedal (recall)
- What you'll notice
- The gas pedal is slow to come back up or stays partly pressed after you lift your foot.
- Why it happens
- Pivot bushings in the accelerator pedal assembly can work loose and make the pedal bind.
- What to do
- Check your VIN for recall 10V-234. If the pedal sticks, shift to neutral, brake to a stop and have the car towed.
Covered free under recall 10V-234. Check your VIN or ask a Jeep dealer.
Stalling or limp mode from throttle body or crank sensor faults
- What you'll notice
- The engine stalls while driving or will not restart, often with an electronic throttle warning light and reduced power.
- Why it happens
- Failing electronic throttle bodies and crankshaft position sensors were common causes of stalling on early models.
- What to do
- Have the codes read and the throttle body and crank sensor checked. Do not rely on the vehicle in traffic until a stalling problem is fixed.
Front and rear crossmembers can rust through (warranty extension X69)
- What you'll notice
- Steering wheel vibration, or heavy rust or holes found on the crossmembers under the car during service or a state inspection.
- Why it happens
- Road salt can corrode the front and rear crossmembers that hold the suspension until they are perforated. Chrysler extended the warranty (X69) and published bulletin 23-007-17 for replacing them.
- What to do
- Have the crossmembers inspected, especially in salt-belt states. Ask a dealer about warranty extension X69. A perforated crossmember must be replaced before more driving.
Engine computer may crack and stall the engine (recall)
- What you'll notice
- The engine suddenly stalls or will not restart, sometimes with a check engine light.
- Why it happens
- Adhesive used when building the powertrain control module could crack its circuit board.
- What to do
- Check your VIN for recall 08V-528 and have the module replaced. A stall in traffic is dangerous, so do not put it off.
Covered free under recall 08V-528. Check your VIN or ask a Jeep dealer.
Seatbelt tensioner and side airbag timing error (recall)
- What you'll notice
- Usually no warning; some vehicles show an airbag light.
- Why it happens
- A software error in the occupant restraint system could delay or stop the seatbelt tensioners and side airbags from firing in a crash.
- What to do
- Check your VIN for recall 13V-233 and have the software updated.
Covered free under recall 13V-233. Check your VIN or ask a Jeep dealer.
Airbag control module may short out (recall)
- What you'll notice
- The airbag warning light comes on and stays on.
- Why it happens
- The occupant restraint control module could short internally, switching off the airbags and seatbelt tensioners.
- What to do
- Check your VIN for recall 16V-668. If the airbag light is on, have it diagnosed promptly; the airbags may not work in a crash.
Covered free under recall 16V-668. Check your VIN or ask a Jeep dealer.
CVT overheats and cuts power
- What you'll notice
- A transmission temperature warning light, sudden loss of power or speed, shuddering or jerking, and a whining sound, often on long highway trips or in hot weather.
- Why it happens
- The continuously variable transmission (CVT) used in these models can run too hot under sustained load, and it then limits power to protect itself. Worn or old fluid makes it worse, and owners filed a class action over these failures.
- What to do
- If the warning light comes on, pull over safely and let the transmission cool before driving on. Have the fluid and cooler checked and ask the dealer about software updates. Repeated overheating needs a transmission inspection.
Steering column rivet may be missing (recall)
- What you'll notice
- Looseness or play in the steering column, or the tilt column not feeling solid.
- Why it happens
- A pivot rivet in the steering column could be missing or out of place, which could let the column separate.
- What to do
- Check your VIN for recall 11V-315. Have any loose-feeling steering inspected before driving further.
Covered free under recall 11V-315. Check your VIN or ask a Jeep dealer.
Fuel tank rollover valve damage (recall)
- What you'll notice
- A fuel smell or wet spots under the rear of the vehicle.
- Why it happens
- The rollover valve on the fuel tank could be damaged during manufacturing, allowing fuel to leak.
- What to do
- Check your VIN for recall 12V-142. If you smell fuel, park outside away from flames and have the tank replaced before driving.
Covered free under recall 12V-142. Check your VIN or ask a Jeep dealer.
Fuel transfer tube may cause stalling (recall)
- What you'll notice
- The engine sputters or stalls when the fuel gauge shows fuel left, often below half a tank.
- Why it happens
- A defective transfer tube inside the fuel tank could stop moving fuel to the pump side.
- What to do
- Check your VIN for recall 13V-120 and have the tube replaced. Keep the tank fuller than usual until it is done.
Covered free under recall 13V-120. Check your VIN or ask a Jeep dealer.
Balance shaft debris can cut oil pressure (recall)
- What you'll notice
- The oil pressure warning comes on, the engine gets noisy, or it stalls.
- Why it happens
- Abrasive debris left in the balance shaft bearings could cause a loss of oil pressure and engine damage.
- What to do
- Check your VIN for recall 13V-552. Stop the engine right away if the oil pressure light comes on.
Covered free under recall 13V-552. Check your VIN or ask a Jeep dealer.
Power steering return hose can come off (recall)
- What you'll notice
- Power steering fluid leaking or a burning smell, steering that suddenly gets heavy, or a whining pump.
- Why it happens
- A hose clamp was put in the wrong place, so the power steering return hose could slip off and spray fluid.
- What to do
- Check your VIN for recall 15V-878. Do not drive if fluid is leaking near hot engine parts; have the clamp repositioned.
Covered free under recall 15V-878. Check your VIN or ask a Jeep dealer.
Crank or cam sensor may stall the engine (recall)
- What you'll notice
- The engine stalls while driving or will not start, sometimes coming back after a few tries.
- Why it happens
- A poor connection at the crankshaft or camshaft position sensor could make the signal drop out.
- What to do
- Check your VIN for recall 16V-907 and have the connector replaced. Avoid heavy traffic until it is repaired.
Covered free under recall 16V-907. Check your VIN or ask a Jeep dealer.
Left front axle shaft may separate (recall)
- What you'll notice
- Clicking or clunking from the front left, or a sudden loss of drive power.
- Why it happens
- On some vehicles with the 6-speed transmission, the left front half shaft could come out of place or break.
- What to do
- Check your VIN for recall 17V-301. Stop driving and have the vehicle towed if you lose drive or hear a sudden clunk.
Covered free under recall 17V-301. Check your VIN or ask a Jeep dealer.
Cracked oil pump housing (recall)
- What you'll notice
- The oil pressure warning comes on, or the engine gets noisy and then stalls.
- Why it happens
- The oil pump housing on some engines can crack, causing a loss of oil pressure.
- What to do
- Check your VIN for recall 17V-670. Stop the engine right away if the oil pressure light comes on.
Covered free under recall 17V-670. Check your VIN or ask a Jeep dealer.
Passenger airbag mounting nuts may be loose (recall)
- What you'll notice
- Usually no warning; some vehicles show an airbag light.
- Why it happens
- The nuts that hold the passenger airbag inflator may not have been tightened, so the airbag might not deploy correctly in a crash.
- What to do
- Check your VIN for recall 17V-732 and have the passenger airbag module replaced.
Covered free under recall 17V-732. Check your VIN or ask a Jeep dealer.
Front lower control arm weld defect (recall)
- What you'll notice
- A clunk from the front suspension, or the vehicle pulling or wandering.
- Why it happens
- Some front lower control arms were not welded correctly and could separate, which affects steering control.
- What to do
- Check your VIN for recall 18V-279. Have any front clunk or wander inspected before driving further.
Covered free under recall 18V-279. Check your VIN or ask a Jeep dealer.
Engine computer chip failure (recall)
- What you'll notice
- The engine stalls while driving or will not start, often with warning lights.
- Why it happens
- A chip inside the powertrain control module could fail.
- What to do
- Check your VIN for recall 18V-524 and have the module replaced. Do not rely on the vehicle in traffic if it has stalled.
Covered free under recall 18V-524. Check your VIN or ask a Jeep dealer.
Reduced rear braking (recall)
- What you'll notice
- A soft or long brake pedal, or stopping distances that seem longer than normal.
- Why it happens
- A coating problem on the rear brake caliper pistons can let gas pockets form in the brake system. The recall bleeds the brakes.
- What to do
- Check your VIN for recall 18V-523 and have it done promptly. Have a soft pedal checked before relying on the vehicle.
Covered free under recall 18V-523. Check your VIN or ask a Jeep dealer.
Engine can shut down after a coolant temperature warning
- What you'll notice
- A dash message says the coolant temperature is too high and the engine cuts out straight away, sometimes in moving traffic. Most restart after a stop, but some have had to be towed.
- Why it happens
- Federal safety investigators opened a review of engine shutdowns on these SUVs after owner reports. The cause has not been pinned down and no recall has been issued.
- What to do
- Pull over somewhere safe if it happens, then have the cooling system, sensors and engine computer checked and the fault reported to the dealer and the safety hotline.
Front control arm bushings and tie rod ends wear out
- What you'll notice
- Clunking over bumps, loose or wandering steering, and uneven front tire wear.
- Why it happens
- The front lower control arm bushings and tie rod ends on these early models wear early, letting the front wheels move out of alignment.
- What to do
- Have the front suspension and steering joints inspected and replaced as needed, followed by an alignment.
Underhood fuse and relay box (TIPM) faults
- What you'll notice
- Random electrical problems such as a no-start, a fuel pump or horn that will not shut off or will not work, or lights and accessories acting up.
- Why it happens
- The Totally Integrated Power Module, the main fuse and relay box under the hood, can fail internally or corrode, which disrupts power to many systems.
- What to do
- Have the TIPM and its connectors tested before replacing other parts. A replacement module may need to be programmed to the vehicle.
Excessive oil consumption
- What you'll notice
- The low oil warning comes on between changes, you keep needing to add oil, or you see blue smoke or fouled spark plugs. Severe cases can stall.
- Why it happens
- The piston oil control rings may not seal well, letting the engine burn oil. A class action settlement extended powertrain coverage for eligible vehicles.
- What to do
- Check the oil at every fill-up and ask a dealer for an oil consumption test and whether extended coverage applies to your VIN.
Windshield wiper arms may loosen (recall)
- What you'll notice
- The wipers skip, stop short, or one arm flops while the motor runs.
- Why it happens
- The nuts holding the wiper arms could loosen, so the wipers may not clear the windshield.
- What to do
- Check your VIN for recall 20V-208 and have the nuts tightened. Avoid driving in heavy rain or snow until it is fixed.
Covered free under recall 20V-208. Check your VIN or ask a Jeep dealer.
Loose front head restraints (recall)
- What you'll notice
- A front headrest feels loose or moves even when locked in place.
- Why it happens
- The front head restraints may not have been welded properly, so they may not protect your head and neck as designed in a crash.
- What to do
- Check your VIN for recall 22V-248 and have both front head restraints replaced.
Covered free under recall 22V-248. Check your VIN or ask a Jeep dealer.
Instrument cluster too dim or not adjustable (recall)
- What you'll notice
- The gauge display is hard to read in daylight, or its brightness will not change.
- Why it happens
- A display that was too dim on some 2022 models, and body control software that blocked brightness adjustment on 2022-2023 models, can make warnings and speed hard to see.
- What to do
- Check your VIN for recalls 23V-058 and 23V-576 and have the cluster or software fixed.
Free under recalls 23V-058 and 23V-576; some 2022 models also get new parts. Check your VIN.
Backup camera image may not show (recall)
- What you'll notice
- The screen stays blank or frozen when you shift into reverse.
- Why it happens
- Radio software can stop the rearview camera picture from displaying.
- What to do
- Check your VIN for recall 24V-436 and get the software update at a dealer or over the air. Use mirrors and look behind you until it is fixed.
Free under recalls 24V-436 and 26V-531, at a dealer or over the air. Check your VIN.
Backup camera image may not show (recall)
- What you'll notice
- The screen stays blank or does not switch to the camera view when you shift into reverse.
- Why it happens
- A radio software fault can keep the rearview camera picture from appearing.
- What to do
- Check your VIN for recall 26V-531 and get the radio software update. Use mirrors and look behind you until it is fixed.
Free under recalls 24V-436 and 26V-531, at a dealer or over the air. Check your VIN.
Roof and sunroof water leaks (TSB)
- What you'll notice
- Damp spots or water stains on the headliner, water dripping from the dome light, or wet carpets after rain or a car wash.
- Why it happens
- Sunroof drain tubes and grommets can leak or kink, and the roof ditch seams can let water in. Chrysler issued bulletin 23-005-13 to replace drain tubes and reseal the roof seams.
- What to do
- Ask a dealer about bulletin 23-005-13. Dry out wet carpets quickly to prevent mold and electrical problems.
Gauge lights cannot be dimmed (recall)
- What you'll notice
- The instrument cluster stays bright at night and the dimmer does nothing.
- Why it happens
- Software in the instrument cluster did not allow the backlighting to be dimmed, which can cause glare at night.
- What to do
- Check your VIN for recall 17V-740 and have the software updated.
Covered free under recall 17V-740. Check your VIN or ask a Jeep dealer.
Repair prices for your Jeep Compass
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace front lower control arms and tie rod ends, then align
- Replace electronic throttle body
- Replace and program the TIPM
- Diagnose roof leak with a water test (bulletin 23-005-13)
- Replace front crossmember
- Change CVT fluid and check the transmission cooler
- Diagnose engine shutdown; test cooling system and sensors
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Reprogram ABS control unitNo charge if your vehicle is included
- Replace accelerator pedal assemblyNo charge if your vehicle is included
- Replace powertrain control moduleNo charge if your vehicle is included
- Update airbag control softwareNo charge if your vehicle is included
- Replace occupant restraint control moduleNo charge if your vehicle is included
- Inspect and repair steering column pivot rivetNo charge if your vehicle is included
- Replace fuel tankNo charge if your vehicle is included
- Replace fuel tank transfer tubeNo charge if your vehicle is included
- Replace engine balance shaft moduleNo charge if your vehicle is included
- Reposition power steering hose clampNo charge if your vehicle is included
- Replace crank or cam sensor connectorNo charge if your vehicle is included
- Inspect and replace left front axle shaftNo charge if your vehicle is included
- Update instrument cluster softwareNo charge if your vehicle is included
- Replace engine oil pumpNo charge if your vehicle is included
- Replace passenger airbag moduleNo charge if your vehicle is included
- Replace front lower control armsNo charge if your vehicle is included
- Bleed the brake systemNo charge if your vehicle is included
- Tighten windshield wiper arm nutsNo charge if your vehicle is included
- Replace both front head restraintsNo charge if your vehicle is included
- Update body control module softwareNo charge if your vehicle is included
- Update radio softwareNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Pick a model year to see its safety recalls.