Your 2013 Mazda Mazda2problems, repair costs and recalls
What we've documented about the 2013 Mazda Mazda2: problems owners and shops report, typical repair and upkeep costs, and safety recalls.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems for your 2013 Mazda Mazda2
8 documented issues apply to 2013, most serious first.
Steering clunks, pops or catches when turning
- What you'll notice
- A clunk, knock or pop from the front end when turning at low speed or parking, or a 'hitch' that you feel through the wheel every few degrees of turning. It often gets worse over time.
- Why it happens
- Wear inside the steering rack is the most common finding, and dealers have replaced racks under warranty. Worn front strut bearings or the steering shaft joint can make a similar noise, so owners sometimes need more than one repair.
- What to do
- Have a shop check the rack, tie rods, strut mounts and steering shaft with the car on the ground and the wheel being turned. Get it fixed promptly; a badly worn rack can make steering unpredictable.
Oil leak from the oil pan gasket
- What you'll notice
- Oil spots under the front of the car and an oily, wet oil pan. The oil level may drop between changes.
- Why it happens
- The sealant joint between the oil pan and the engine can seep. Owners report it from around 30,000 miles, and some were fixed under warranty.
- What to do
- Check the oil level often and keep it topped up. Have the pan resealed before the leak gets worse or drips onto hot exhaust parts.
Broken or worn engine mount
- What you'll notice
- More vibration felt in the cabin at idle, a thunk when shifting or pulling away, or clunks over bumps.
- Why it happens
- The rubber engine mounts wear out or tear over time, letting the engine move more than it should.
- What to do
- Have the mounts checked, especially if the car vibrates more than it used to. Replacing a torn mount is a moderate job and prevents strain on hoses, exhaust and other mounts.
Brake shudder from warped rotors or sticking calipers
- What you'll notice
- The steering wheel or brake pedal shakes when braking from speed, brakes creak or drag, or one front wheel gets very hot.
- Why it happens
- Front brake rotors can wear unevenly and cause pulsing, and owners have also reported front calipers seizing at higher mileage.
- What to do
- Have the brakes inspected. Resurfacing or replacing the rotors usually cures shudder; a sticking caliper should be replaced right away because it wears pads fast and pulls the car.
Manual clutch slave cylinder leaks, soft clutch or grinding shifts
- What you'll notice
- The clutch pedal feels soft or squeaks, gears grind (especially 2nd and 3rd) or are hard to get into.
- Why it happens
- The clutch slave cylinder can leak or wear out, so the clutch doesn't fully release. Owners whose gears grind sometimes find the slave cylinder was the real cause.
- What to do
- Have the clutch hydraulics checked before assuming the gearbox is bad. Replacing the slave cylinder and bleeding the system is far cheaper than a transmission repair.
Loud or noisy heater blower fan
- What you'll notice
- The fan behind the dashboard gets loud, whines or rattles, especially at certain speeds.
- Why it happens
- The blower motor bearings wear, or debris gets into the fan. Several early Mazda2s had the blower replaced under warranty.
- What to do
- Have the cabin air filter and blower checked. If the motor itself is noisy, replacing it is the fix.
Radio cuts out with no sound
- What you'll notice
- The radio display stays on but the sound cuts out, no matter whether you use radio, CD or AUX.
- Why it happens
- An owner report ties this to faulty factory radio units that were not recalled.
- What to do
- Check fuses and connections first. If the head unit itself has failed, a replacement radio is the fix.
Headlight wiring damaged by water
- What you'll notice
- A headlight flickers or stops working, and the plug may look melted.
- Why it happens
- Water can get into the headlight wiring connector, causing a short and heat damage.
- What to do
- Have the bulb plug and harness inspected. Replace a melted connector rather than just the bulb.
Repair prices for your 2013 Mazda Mazda2
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace steering rack and align
- Reseal oil pan
- Replace engine mount
- Replace heater blower motor
- Replace front brake rotors and pads
- Replace clutch slave cylinder and bleed
- Replace radio head unit
- Replace headlight wiring connector
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Checking the NHTSA recall database…