Nissan Altimaproblems, repair costs and recalls
Problems reported across 1996–2025. Pick your model year below to see what applies to your vehicle.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems
33 documented issues across all years, most serious first.
Pre-catalytic converter breakdown and oil consumption
- What you'll notice
- Oil level drops between changes, blue smoke, a rattle from the exhaust manifold area, loss of power or a check engine light for the catalyst.
- Why it happens
- The small converter built into the exhaust manifold can overheat and break apart. Pieces can be pulled back into the cylinders and score them, which leads to heavy oil burning. Early 2002 cars were also recalled for an exhaust fire risk tied to the catalyst.
- What to do
- Check the oil level often and do not let it run low. Get any manifold rattle or catalyst code checked right away, and confirm the 2002 recall was done.
Engine stalls from crankshaft or camshaft sensor fault (recall)
- What you'll notice
- The engine shuts off without warning at low speed, or the car is hard to start, misfires, or runs with a check engine light.
- Why it happens
- The crankshaft position sensor can overheat and drop its signal for a moment, too briefly for the computer to flag it, and the engine stops. An earlier recall covered poorly welded crank and cam sensors.
- What to do
- Have a Nissan dealer check your VIN for the engine computer update and sensor recalls. If the car stalls, stop driving it until it is checked.
Driver airbag may not deploy (recall)
- What you'll notice
- Usually no warning; an airbag light may be on.
- Why it happens
- Some driver airbag modules were built with a defect that could keep them from deploying in a crash.
- What to do
- Check your VIN for open recalls and have a Nissan dealer replace the module if it has not been done.
CVT shudder, whine or failure
- What you'll notice
- Shudder or slipping when pulling away, a whine or hum that rises with speed, and weak or delayed acceleration.
- Why it happens
- The early Nissan CVT in this generation has a record of wear, with more complaints on 2007-2009 cars. Nissan's extended CVT warranty for 2003-2010 CVT models has largely run out.
- What to do
- Use only the correct Nissan CVT fluid and change it on schedule. Get a diagnosis at the first shudder or whine before the damage spreads.
Passenger airbag switches off with an adult seated (recall)
- What you'll notice
- The passenger airbag OFF light stays on even when an adult is in the seat.
- Why it happens
- A part in the passenger seat occupant sensor was out of spec and could interrupt its signal, so the system thinks the seat is empty.
- What to do
- Check your VIN for the recall. Until it is repaired, avoid putting an adult in the front passenger seat when the OFF light is on.
Front strut mount insulator can crack (recall)
- What you'll notice
- Knocking or clunking from the front suspension over bumps.
- Why it happens
- Some upper strut insulators were out of spec and can crack, letting the strut rod work loose from its mount and affecting control.
- What to do
- Check your VIN for the recall and have the front struts inspected promptly if you hear knocking. Do not ignore a new clunk from the front end.
Loose suspension and steering rack bolts (recall)
- What you'll notice
- Clunking over bumps or a loose, vague feel in the steering.
- Why it happens
- On some cars built in mid-2012, bolts holding suspension and steering parts were not tightened to spec at the factory.
- What to do
- Check your VIN for the recall and have the bolts inspected before driving much further if the steering feels loose.
CVT judder, hesitation or failure
- What you'll notice
- Judder or vibration when accelerating, hesitation, surging, whining, a transmission warning light, or in some cases loss of drive.
- Why it happens
- The CVT in these cars has a long complaint record. Nissan issued a bulletin for judder with codes P17F0 or P17F1 on 4-cylinder cars, and class-action settlements extended CVT coverage on 2013-2018 models to 7 years or 84,000 miles.
- What to do
- Ask a Nissan dealer about the judder bulletin and whether any extended coverage still applies to your VIN. Get a diagnosis at the first shudder.
Hood can fly open while driving (recall)
- What you'll notice
- The hood lifts slightly after being closed, or is not held by the safety catch after the release lever is pulled.
- Why it happens
- The secondary hood latch can corrode or bind and stay open. Several earlier recalls on 2013-2015 cars did not fully cure it, so Nissan recalled 2013-2018 cars again.
- What to do
- Check your VIN for open hood latch recalls. Always confirm the hood is fully latched before driving, and do not drive if it will not stay latched.
Rear door can open when the window is lowered (recall)
- What you'll notice
- A rear door unlatches or pops open when its window goes down.
- Why it happens
- The rear door latch cable could be routed wrong at the factory and pulls the latch when the window moves.
- What to do
- Check your VIN for the recall. Use the child locks and keep rear windows up until the repair is done.
Passenger airbag may turn off with an adult seated (recall)
- What you'll notice
- The passenger airbag OFF light comes on even though an adult is sitting there.
- Why it happens
- The occupant classification system can misread an adult as a child or an empty seat, so the airbag would not deploy.
- What to do
- Check your VIN for both occupant-sensor recalls. Until fixed, avoid seating an adult in front when the OFF light is on.
VC-Turbo engine bearing failure (recall)
- What you'll notice
- Knocking from the engine, loss of power, or the engine quitting while driving. In rare cases oil escapes and catches fire.
- Why it happens
- Some engine bearings were made with defects that can lead to engine failure. A federal investigation covered 2019-2021 cars, and Nissan recalled 2019-2020 cars.
- What to do
- Check your VIN for the recall and have the engine software update done. If you hear knocking or lose power, pull over safely and have the car towed.
Fuel line clip may not be locked (recall)
- What you'll notice
- A fuel smell under the hood, or the engine stalling.
- Why it happens
- A clip connecting the low-pressure fuel line to the high-pressure pump may not have been locked at the factory, so fuel can leak.
- What to do
- If you smell fuel, stop driving and have the car checked. Check your VIN for the recall.
Tie rod nut may be loose (recall)
- What you'll notice
- A clunk or looseness in the steering, or the car pulling.
- Why it happens
- The nut on the outer tie rod ball joint may not have been tightened properly, and the joint could separate from the steering knuckle.
- What to do
- Check your VIN for the recall. If the steering feels loose or clunks, stop driving and have it inspected.
Door striker may break (recall)
- What you'll notice
- A door does not latch firmly or feels loose when closed.
- Why it happens
- Some door strikers were poorly welded and can break, which could let a door open while driving.
- What to do
- Check your VIN for the recall. Do not drive with a door that will not latch firmly.
Front passenger airbags may not deploy correctly (recall)
- What you'll notice
- Usually no warning signs before a crash.
- Why it happens
- The wrong fasteners were used to mount the passenger and knee airbags.
- What to do
- Check your VIN for the recall and have a Nissan dealer make the repair as soon as possible.
Seat belt buckle may be brittle (recall 96V-185)
- What you'll notice
- No warning. The buckle may fail to hold in a crash.
- Why it happens
- The metal base of some seat belt buckles was not heat-treated correctly.
- What to do
- Make sure this old recall was completed. The repair is free at a dealer. Ask the dealer to check your VIN to see if it was already done.
Left front lower control arm bolt may be loose (recall 08V-363)
- What you'll notice
- Clunk from the left front, loose or wandering steering.
- Why it happens
- A bolt on the left front lower control arm (transverse link) may not have been tightened fully at the factory.
- What to do
- Have it checked before driving far if the recall is open. The repair is free at a dealer. Ask the dealer to check your VIN to see if it was already done.
Lug nuts can loosen on 16-inch alloy wheels (recall 08V-464)
- What you'll notice
- Clicking or wobble from a wheel, vibration that gets worse.
- Why it happens
- Certain 16-inch alloy wheels do not seat the lug nuts correctly, so they can back off.
- What to do
- Stop and check the lug nuts if a wheel feels loose. The repair is free at a dealer. Ask the dealer to check your VIN to see if it was already done.
Front lower control arm bolt may loosen (recall 11V-371)
- What you'll notice
- Rattle or clunk from the front end and vague steering.
- Why it happens
- A front lower control arm (transverse link) bolt may not have been tightened to spec and can work loose.
- What to do
- Have it checked before driving far if the recall is open. The repair is free at a dealer. Ask the dealer to check your VIN to see if it was already done.
Airbag control unit built incorrectly (recall 11V-408)
- What you'll notice
- Airbag warning light may be on, or there may be no sign.
- Why it happens
- The airbag control unit was assembled wrong, so the airbags may not inflate in a crash.
- What to do
- Have the recall done promptly. The repair is free at a dealer. Ask the dealer to check your VIN to see if it was already done.
Side curtain airbags may not inflate (recall 12V-055)
- What you'll notice
- No warning before a crash.
- Why it happens
- The inflators for the side curtain airbags may contain the wrong gas-producing mix.
- What to do
- Have the recall done promptly. The repair is free at a dealer. Ask the dealer to check your VIN to see if it was already done.
Steering rack bolts may loosen (recall 23V-882)
- What you'll notice
- Clunk or looseness in the steering, or steering that suddenly feels wrong.
- Why it happens
- Bolts that join the power steering unit to the steering rack may come loose.
- What to do
- Stop driving if the steering feels loose and have the recall done. The repair is free at a dealer. Ask the dealer to check your VIN to see if it was already done.
Certain Firestone Firehawk tires can crack and lose air (campaign)
- What you'll notice
- Cracks or bulges appear in the tire shoulder, and a tire can lose air quickly or shed tread.
- Why it happens
- Specific Firehawk GTA-02 tires fitted to these cars can crack at the shoulder and separate at the belt edge.
- What to do
- Check the tire serial numbers against the campaign and have affected tires replaced before driving at speed.
Distributor failure causes stalling or no-start
- What you'll notice
- The engine stalls at low speed or at stops, idles roughly, misfires, or cranks without starting.
- Why it happens
- The distributor on this engine is a known weak point as it ages, and a failing unit interrupts spark.
- What to do
- Have the ignition system tested before replacing parts at random; a worn distributor is a common finding on these cars.
Ignition coil failure and misfires
- What you'll notice
- Check engine light with a misfire code, shaking at idle, bucking under acceleration and worse fuel economy.
- Why it happens
- The coil-on-plug ignition coils on this engine wear out with age and are a frequent repair on these cars.
- What to do
- Have the misfiring cylinder identified and the bad coil replaced; replace old spark plugs at the same time. A flashing check engine light means stop soon to protect the converter.
Steering lock failure, car won't start
- What you'll notice
- Push-button start does nothing, the steering wheel stays locked, and a key or steering warning shows on the dash.
- Why it happens
- The electronic steering column lock can fail to release, and the car will not start while it reads locked. Nissan ran a service campaign on this part.
- What to do
- Ask a Nissan dealer whether the steering lock campaign applies to your VIN. The lock unit usually needs replacing and a tow may be required.
Backup camera image can disappear (recall)
- What you'll notice
- No rear camera picture when backing up after a display setting was changed.
- Why it happens
- Certain display settings can switch off the rear camera image and it stays off.
- What to do
- Check your VIN for the recall and have the software updated. Look behind you directly when reversing until then.
Rearview camera image flickers or goes blank (recall)
- What you'll notice
- The backup camera picture flickers, looks distorted, or is missing.
- Why it happens
- The camera wiring harness can be damaged and lose its connection.
- What to do
- Check your VIN for the recall. Look behind you directly when reversing until it is repaired.
Intake manifold gasket vacuum leak causes rough idle
- What you'll notice
- Shaky or unsteady idle at stop lights, near-stalling, a hissing sound from the engine and a check engine light, often with a misfire on one cylinder.
- Why it happens
- The gasket between the intake manifold and the engine hardens with age and lets extra air in, commonly at the cylinder nearest the transmission.
- What to do
- Have a shop confirm the leak and replace the gasket. It is safe to drive short term, but stalling at stops will get worse.
Engine air filter can catch fire (recall 07V-267)
- What you'll notice
- Burning smell or smoke from the air filter box under the hood.
- Why it happens
- The air filter material can ignite if something hot is drawn into the air intake.
- What to do
- Have the recall done soon, and stop if you see smoke. The repair is free at a dealer. Ask the dealer to check your VIN to see if it was already done.
Tire pressure warning system may have been switched off (recall)
- What you'll notice
- No low tire warning ever appears, even with a clearly soft tire.
- Why it happens
- The monitoring system could be left deactivated after a dealer replaced the body control module.
- What to do
- Have the system reactivated under the recall and check pressures by hand in the meantime.
Front brakes can grind or feel weak early in the car life
- What you'll notice
- Grinding or scraping from the front wheels when you slow down, and a pedal that feels long or soft, often well before the first brake job would normally be due.
- Why it happens
- Owners of these years report front pads and rotors wearing out unusually early, and some report the pedal going soft once the brakes are hot.
- What to do
- Have the pads, rotors and brake fluid inspected now rather than waiting for a service interval, and ask the dealer whether any bulletin applies.
Repair prices for your Nissan Altima
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace distributor assembly
- Replace exhaust manifold with pre-catalytic converter
- Update engine computer software; replace crank sensor if failed
- Replace ignition coils (set of 4) and spark plugs
- Install retaining clip on airbag clock spring connector
- Replace CVT with a remanufactured unit
- Replace electronic steering column lock
- Test occupant sensor; replace seat cushion if faulty
- Replace both front strut mount insulators
- Torque suspension link and steering rack bolts
- Install stronger hood release spring and lube secondary latch
- Reroute and secure rear door latch/lock cables
- Reprogram airbag and occupant sensor control units
- Update backup camera software
- Inspect oil pan for debris; replace engine if damaged
- Seat and lock fuel line retainer clip
- Inspect and reroute camera harness; replace if damaged
- Tighten or replace tie rod ball joint fasteners
- Replace door strikers
- Replace passenger airbag mounting bolts
- Replace intake manifold gasket
- Replace seat belt buckle
- Replace engine air filter
- Inspect and torque control arm bolt
- Inspect or replace alloy wheels
- Inspect and torque control arm bolts
- Replace airbag control unit
- Replace side curtain airbag modules
- Replace steering rack assembly
- Replace affected tires and balance
- Reactivate and test the tire pressure monitoring system
- Replace front brake pads and rotors
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Pick a model year to see its safety recalls.