Porsche Boxster / Caymanproblems, repair costs and recalls
Problems reported across 1997–2025. Pick your model year below to see what applies to your vehicle.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems
32 documented issues across all years, most serious first.
IMS bearing failure
- What you'll notice
- Often no warning. Some cars show metal in the oil filter, an oil drip at the back of the engine, or a knocking or grinding noise from the rear of the engine.
- Why it happens
- The intermediate shaft (IMS) bearing in these engines is sealed and can lose its grease and fail, wrecking the engine. The single-row bearing used around 2002-2005 has the highest failure rate. 2009 and newer engines have no IMS bearing.
- What to do
- Ask for proof the bearing was upgraded. Many owners fit an upgraded bearing at the next clutch change. If you hear knocking from the back of the engine, stop driving.
Cylinder bore scoring
- What you'll notice
- Rising oil use, blue smoke, tapping or ticking from the engine, low oil level, and sooty tailpipes.
- Why it happens
- The cylinder walls can get scratched by the pistons. PistonHeads says it hit about 1 in 20 pre-2009 engines, mostly the 3.4 S, and was almost unheard of on the 2.7.
- What to do
- Have a specialist do a borescope (camera) check of the cylinders before buying or when oil use rises.
Oil and coolant mixing on early engines
- What you'll notice
- Milky oil on the dipstick, oil in the coolant tank, white exhaust smoke, or overheating.
- Why it happens
- Early engines had casting weaknesses, and cracked cylinder heads or failed seals can let oil and coolant mix.
- What to do
- Stop driving and have the fluids checked. If buying, check the dipstick and the oil and coolant fillers for any sign of mixing.
Water pump failure
- What you'll notice
- Coolant leaks, a coolant smell, a whining noise, or the temperature gauge rising.
- Why it happens
- Water pumps on these cars may last only about 40,000 miles. The plastic impeller can crack and send debris through the system, and a failed pump can lead to head gasket damage.
- What to do
- If the temperature climbs, stop and turn the engine off. Many owners replace the pump as preventive maintenance.
Tiptronic shifter can leave Park without key (recall)
- What you'll notice
- The shift lever can be moved out of Park with the key out.
- Why it happens
- A misadjusted key-lock cable may let the shifter leave Park, which could let the car roll away.
- What to do
- Always set the parking brake and have a dealer inspect and adjust the cable for free.
Free at a Porsche dealer under the recall. Check your VIN.
Front hood may not latch (recall)
- What you'll notice
- The front lid may not stay securely closed.
- Why it happens
- Hood lock parts built out of specification on cars made in mid-2014 may not latch properly.
- What to do
- Have a dealer replace the front hood lock for free.
Free at a Porsche dealer under the recall. Check your VIN.
Airbag control unit capacitor fault (recall)
- What you'll notice
- The airbag warning light may come on.
- Why it happens
- A capacitor in the airbag control unit can fail, so the airbags may switch off or go off unexpectedly.
- What to do
- Have a dealer update the software and replace the unit if needed. It's free.
Free at a Porsche dealer under the recall. Check your VIN.
Seat side airbag may not deploy (recall)
- What you'll notice
- Usually no warning sign.
- Why it happens
- The side airbag initiator in the seats of some 2017 718 Boxsters and Caymans may not fire in a crash.
- What to do
- Have a dealer replace the side airbag modules for free.
Free at a Porsche dealer under the recall. Check your VIN.
Trunk bracket could puncture fuel tank in a crash (recall)
- What you'll notice
- No sign in normal driving.
- Why it happens
- A luggage compartment bracket could puncture the fuel tank in a certain type of collision. Porsche recalled over 14,000 718 Boxsters and Caymans in early 2019.
- What to do
- Check with a dealer that the bracket fix has been done. It's free.
Free at a Porsche dealer under the recall. Check your VIN.
GT4 connecting rods can crack (recall)
- What you'll notice
- Knocking from the bottom of the engine, stalling, loss of power, or oil leaks.
- Why it happens
- GT4s built from late January to early March 2021 got connecting rods that were out of specification and can crack.
- What to do
- Check with a dealer. Engines that had run were replaced; unrun engines got new rods and, in the US, a 10-year engine warranty.
Free at a Porsche dealer under the recall. Check your VIN.
PDK may not lock in Park (recall)
- What you'll notice
- The car may roll even when the shifter shows Park.
- Why it happens
- A safety clip on the shift cable may be installed wrongly, so the transmission may not lock in Park.
- What to do
- Always use the parking brake. Have a dealer replace the shift cable for free.
Free at a Porsche dealer under the recall. Check your VIN.
Center-lock wheel bolt may fracture on GT4 RS and Spyder RS (recall)
- What you'll notice
- A loose or vibrating wheel. Porsche said not to drive until repaired.
- Why it happens
- On 2024 Cayman GT4 RS and Spyder RS models, the center-lock wheel bolt may crack, which could let a wheel come off.
- What to do
- Don't drive the car until a dealer has checked and replaced faulty parts. It's free.
Free at a Porsche dealer under the recall. Check your VIN.
Rear main seal oil leak
- What you'll notice
- Oil drips where the engine meets the gearbox.
- Why it happens
- The crankshaft rear seal leaks, often because the seal bore in the crankcase was machined slightly off-center. It mostly affected the 986, with fewer 987s.
- What to do
- A small seep is not urgent. Because the gearbox has to come out, it's best done with a clutch or IMS job.
Air-oil separator failure (blue smoke)
- What you'll notice
- Blue or white smoke while driving or after start-up, high oil use, rough running or lean fuel codes.
- Why it happens
- The air-oil separator, which vents crankcase gases, can fail internally and let oil be drawn into the intake. RepairPal lists this as the most reported Boxster problem.
- What to do
- Check that the oil is not overfilled. Have the separator tested and replaced if needed.
Cracked coolant expansion tank
- What you'll notice
- Coolant level keeps dropping or coolant leaks into the trunk area.
- Why it happens
- The plastic expansion tank on the 986 cracks with age.
- What to do
- Have the tank pressure-tested and replaced before it leads to overheating.
Misfire from cracked ignition coil packs
- What you'll notice
- Check engine light, rough running, shaking or stuttering under power.
- Why it happens
- The coil packs crack from heat and water splash.
- What to do
- Have the misfire codes read and replace the failed coil, often along with the spark plugs.
Corroded front radiators and A/C condensers
- What you'll notice
- Engine running warm, weak air conditioning, or leaks behind the front bumper. Leaves in the bumper vents.
- Why it happens
- The radiators and condensers sit behind the bumper openings, where trapped leaves hold moisture and corrode them. They may last only six to eight years.
- What to do
- Keep the bumper vents clear of debris. Replace a leaking radiator or condenser before the engine overheats.
Timing chain rattle at idle
- What you'll notice
- A rattle at idle or at cold start.
- Why it happens
- The timing chains and their tensioners and guide pads wear, especially with long oil-change intervals.
- What to do
- Have it checked soon. Classic & Sports Car says worn cam chains need urgent replacement.
Worn suspension bushings and joints
- What you'll notice
- Knocking or creaking over bumps, groaning from the front when maneuvering, and odd tire wear.
- Why it happens
- Suspension joints and rubber bushings, especially on the trailing arms and lower arms, often wear out by about 30,000-40,000 miles. Top mounts also wear.
- What to do
- Have the suspension inspected and the alignment checked after repairs.
Broken coil springs
- What you'll notice
- The car sits unevenly or makes clunks on rough roads.
- Why it happens
- Coil spring breakage is very common on the 987.
- What to do
- Have the springs inspected. A broken spring can damage a tire, so replace it promptly, ideally in pairs.
Six-speed manual jumping out of second gear
- What you'll notice
- The gearbox pops out of second gear under acceleration or deceleration.
- Why it happens
- The six-speed manual can slip out of second because of wear in the selector detent.
- What to do
- Have the gearbox inspected. The fix means stripping the gearbox and fitting a modified detent.
Water behind seats from blocked roof drains
- What you'll notice
- Wet carpet behind the seats, damp smells, or electrical faults.
- Why it happens
- The drains for the soft top and hood area block with debris, so water collects behind the seats where a control unit sits.
- What to do
- Clear the drains regularly. Water reaching the control unit can mean an expensive replacement.
Cracked exhaust manifold
- What you'll notice
- Engine sounds louder or harsher and feels sluggish.
- Why it happens
- The exhaust manifolds can crack from heat.
- What to do
- Have the exhaust inspected for leaks; exhaust leaks can also upset the oxygen sensors.
Leaking PASM shock absorbers
- What you'll notice
- A bouncy or harsh ride, a suspension warning, or oil on the shock body.
- Why it happens
- The adaptive PASM dampers can leak.
- What to do
- Have the shocks checked on a lift. Replace in pairs.
Brake lights stay on from binding pedal bushes
- What you'll notice
- Brake lights stay on and the PSM stability warning lights up. The brakes may run hot.
- Why it happens
- Bushes in the brake pedal can bind, so the pedal doesn't fully return.
- What to do
- Get it fixed soon, because the brakes can overheat if left. The fix needs a special tool.
Water pump or thermostat failure
- What you'll notice
- Coolant loss, warning lights, overheating, or odd running in cold weather.
- Why it happens
- On the 718, a failing water pump can drip coolant onto a vacuum hose. That can gum up vacuum valves, which then work on and off in the cold.
- What to do
- Have the cooling system pressure-tested and check the vacuum valves at the same time.
Overheating from leaking transmission cooler valve
- What you'll notice
- Temperature warning or the engine running hot.
- Why it happens
- A leaking solenoid valve in the transmission cooling circuit can cause overheating.
- What to do
- Stop if the temperature warning comes on and have the cooling system checked.
Hesitation from failing mass air flow sensor
- What you'll notice
- Stuttering or hesitation when you accelerate, and sometimes a check engine light.
- Why it happens
- The mass air flow (MAF) sensor gets dirty or fails and sends wrong readings.
- What to do
- Have the codes read and the sensor tested. Cleaning sometimes helps; otherwise replace it.
Windows not dropping when doors open
- What you'll notice
- The windows don't lower slightly when you open a door, or lower unexpectedly.
- Why it happens
- A microswitch in the door handle that controls the window drop fails. RepairPal lists this as a common Boxster problem.
- What to do
- Have the door handle switch replaced. Shutting the door with the window up can damage the seals or roof.
Direct-injection carbon buildup and fuel pump wear
- What you'll notice
- Gradual loss of smoothness or power, rough idle, or fuel-pressure check engine codes.
- Why it happens
- Direct-injection engines can build up deposits on the intake valves and wear the high-pressure fuel pump. The base 2.7 on the 981 uses port injection and avoids this.
- What to do
- Use good fuel and keep up with oil changes. Have codes read if the engine runs rough.
Intermittent misfire that clears after restart
- What you'll notice
- A slight misfire or rough running that goes away after switching off and on.
- Why it happens
- PistonHeads says this is often linked to a weak 12-volt battery.
- What to do
- Have the battery tested first. Watching battery voltage on the dash display can give early warning.
Infotainment Bluetooth dropping or screen faults
- What you'll notice
- Phones keep disconnecting, or the touchscreen stops working properly.
- Why it happens
- The PCM infotainment unit can need recoding, and some touchscreens were replaced under warranty.
- What to do
- Ask a dealer to recode the PCM; that usually fixes Bluetooth. Screen faults may need a new unit.
Repair prices for your Porsche Boxster / Cayman
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace IMS bearing with upgraded kit (done with clutch and rear main seal)
- Engine rebuild with new cylinder liners
- Replace rear main seal (gearbox removed)
- Engine rebuild or replacement
- Replace air-oil separator
- Replace water pump and thermostat
- Replace coolant expansion tank and cap
- Replace ignition coil packs
- Replace mass air flow sensor
- Replace one front radiator or A/C condenser
- Replace timing chain tensioners and guides
- Replace control arms or bushings and align
- Replace coil springs (pair)
- Gearbox strip and detent repair
- Clear roof and hood drains
- Replace door handle microswitch
- Replace exhaust manifold
- Intake valve cleaning or high-pressure fuel pump
- Replace PASM shock absorber (per corner)
- Replace brake pedal bushes
- Test and replace 12-volt battery
- Replace transmission cooler solenoid valve
- Recode or replace PCM infotainment unit
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Inspect and adjust key-lock cableNo charge if your vehicle is included
- Replace front hood lockNo charge if your vehicle is included
- Update software and replace airbag control unit as neededNo charge if your vehicle is included
- Replace seat side airbag modulesNo charge if your vehicle is included
- Modify luggage compartment bracketNo charge if your vehicle is included
- Replace connecting rods or engineNo charge if your vehicle is included
- Replace shift cableNo charge if your vehicle is included
- Inspect and replace center-lock wheel partsNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Pick a model year to see its safety recalls.