Your 2008 Scion xDproblems, repair costs and recalls
What we've documented about the 2008 Scion xD: problems owners and shops report, typical repair and upkeep costs, and safety recalls.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems for your 2008 Scion xD
24 documented issues apply to 2008, most serious first.
Engine failure or blown head gasket at high mileage
- What you'll notice
- White smoke from the exhaust, coolant loss with no visible leak, overheating, loss of power, or a loud knock followed by the engine quitting. Most reports come at around 100,000 to 115,000 miles.
- Why it happens
- Engine problems are the most-reported category for the 2008 xD. Owners report blown head gaskets, compression loss and, in some cases, a failed connecting rod. Overheating from a leaking water pump or low oil can lead to this kind of damage.
- What to do
- Stop driving if the engine overheats, knocks or smokes heavily. Have a shop do a compression or leak-down test to find out whether the head gasket or the whole engine is damaged before deciding on a repair.
Driver's power window switch can overheat (recall)
- What you'll notice
- The driver's window switch feels sticky or works on and off, gets hot, or gives off a burning smell or smoke.
- Why it happens
- The grease on the switch contacts was applied unevenly at the factory, so the switch can short, overheat, melt and possibly start a fire. Toyota issued two recalls (12V-491 for 2008-2009 and 15V-689 for 2009-2010).
- What to do
- If you smell burning or the switch gets hot, stop using it and have the car checked. Look up your VIN for open recalls; the dealer inspects, regreases or replaces the switch for free.
Front seat may not lock in place (recall)
- What you'll notice
- The driver's or front passenger seat slides or won't stay locked after you adjust it.
- Why it happens
- Springs in the seat rails can break, so the seat may not latch and could move in a crash. Recall 14V-169 covers xDs built from April 2007 to May 2010.
- What to do
- If a seat won't lock firmly, don't use that seat until it is fixed. Check your VIN for open recalls; the dealer inspects and replaces the seat rail for free.
Hard brake pedal in extreme cold (recall)
- What you'll notice
- In very cold weather the brake pedal feels hard and the car takes longer to stop.
- Why it happens
- Moisture from the engine's crankcase ventilation could freeze in the port that feeds vacuum to the brake booster, reducing power assist. Recall 09V-338 covers 2008-2009 xDs in cold-weather states.
- What to do
- If the pedal feels unusually hard in the cold, brake earlier and gently and have the car checked. Look up your VIN; the dealer installs a redesigned intake connector for free.
Water pump leaking coolant or whining
- What you'll notice
- Pink or reddish coolant drips under the passenger side of the engine, a sweet smell, the coolant level keeps dropping, or a grinding or squealing noise from the belt area.
- Why it happens
- The water pump seal on this 1.8L engine (the same engine used in the Corolla and Matrix) wears out early. Toyota issued a service bulletin for coolant leaks and noise from the pump. It is the most-reported repair for the xD.
- What to do
- Check the coolant level when the engine is cold and top up if low. If the temperature gauge climbs, stop driving to avoid overheating. Have the pump replaced, and replace the drive belt at the same time.
Oil leak from the timing chain cover
- What you'll notice
- Oil seeping down the passenger side of the engine, oil spots under the car, or a burning oil smell after driving.
- Why it happens
- The sealant along the timing chain cover on this engine can weep oil as the car ages. The oil pressure switch nearby can also leak and is a cheaper fix, so it should be ruled out first.
- What to do
- Keep an eye on the oil level. Ask a shop to confirm exactly where the leak comes from, since the oil pressure switch is much cheaper than resealing the timing cover. A small weep can be watched; a steady drip should be fixed.
Engine burning oil
- What you'll notice
- The oil level drops between changes, sometimes with blue smoke from the exhaust or an oil-fouled spark plug.
- Why it happens
- Toyota issued a service bulletin for oil consumption on this 1.8L engine. Owners report a dealer engine computer update as the fix.
- What to do
- Check the dipstick every few fill-ups and top up as needed. Ask a Toyota dealer whether your car has had the oil-consumption bulletin done.
Long cranking, no start or misfire codes
- What you'll notice
- The engine cranks for a long time before starting or won't start at all, sometimes with the check engine light on for misfires (P0300-P0304) or cam timing (P0015).
- Why it happens
- Toyota issued a service bulletin for no-start, extended cranking and these codes on early xDs. Owners report carbon buildup and an engine computer update as the fix.
- What to do
- Have the codes read and ask a Toyota dealer whether the bulletin applies. Also check the battery and its terminals, since a weak battery can cause similar slow starts.
Misfire from a failed ignition coil
- What you'll notice
- The engine shakes or runs rough, feels down on power, and the check engine light comes on or flashes, often with a code from P0301 to P0304.
- Why it happens
- Each cylinder has its own ignition coil, and they can fail with age and heat. Owners report replacing one or more coils, often at 100,000 miles or more.
- What to do
- If the check engine light is flashing, ease off and avoid hard driving, since a severe misfire can damage the catalytic converter. Have the codes read; the coil is usually quick to swap, and old spark plugs should be replaced at the same time.
Alternator stops charging
- What you'll notice
- The battery warning light comes on while driving, lights dim, the battery keeps going flat, or the car dies and won't restart. Steering may get heavy if the voltage drops far enough.
- Why it happens
- The alternator is one of the most-replaced parts on the xD, often failing somewhere between 40,000 and 140,000 miles.
- What to do
- If the battery light comes on, head to a shop while the car still runs, and turn off accessories you don't need. Have the charging system tested before buying a new battery.
ABS, VSC and brake lights on from a rear wheel speed sensor
- What you'll notice
- The ABS, stability control (VSC) and brake warning lights come on together, sometimes coming and going. Anti-lock braking may not work, especially in snow.
- Why it happens
- The rear wheel speed sensors and their wiring on the 2008 xD fail often, sometimes after corrosion or freezing. ABS and VSC warning lights are among the most-reported brake complaints for this year.
- What to do
- Normal braking still works, but ABS may not, so leave more stopping room, especially on slick roads. Have the ABS code read (often C0210 or similar) to find which sensor or wiring has failed.
Starter clicks but engine won't crank
- What you'll notice
- You turn the key and hear a single click, or nothing, and the engine doesn't turn over, even though the lights work.
- Why it happens
- The starter motor wears out with age and high mileage. A weak battery or corroded terminals can cause the same symptom and should be checked first.
- What to do
- Check that the battery terminals are clean and tight and have the battery tested. If the battery is good, the starter is the likely cause.
Wheel bearing hum
- What you'll notice
- A humming or growling noise that gets louder with speed and may change when you turn. Vibration in corners at high mileage.
- Why it happens
- Wheel bearings wear out over time. They are among the most-reported repairs on the xD, and on the rear they come as a hub assembly with the ABS sensor.
- What to do
- Have it checked soon. A badly worn bearing can overheat or let the wheel wobble, so don't ignore a growl that keeps getting louder.
Manual transmission clutch slipping or wearing out
- What you'll notice
- On manual cars, the engine revs climb without the car speeding up, the clutch engages high on the pedal, or there's a burning smell after hills.
- Why it happens
- Clutch wear is one of the most-reported problems on the xD, with some owners needing a clutch as early as 55,000 miles.
- What to do
- Avoid resting your foot on the clutch and hard launches. If it slips, have it replaced before it leaves you stranded, and have the flywheel checked at the same time.
Rear brakes or parking brake sticking
- What you'll notice
- Grinding or scraping from the rear, the car pulling or dragging, a hot wheel, or a parking brake that stays stuck on.
- Why it happens
- Rear brake parts can rust and seize if they aren't cleaned and lubricated, especially in winter climates. Owners report frozen calipers and parking brakes.
- What to do
- Have the rear brakes cleaned and checked at least once a year. If a wheel is very hot or smells burnt after driving, get it looked at before driving further.
Brief rattle or knock at cold start
- What you'll notice
- A short knocking or rattling sound for a second or two right after starting a cold engine, then it goes away.
- Why it happens
- The camshaft timing gear (the part that adjusts valve timing) can rattle briefly before oil pressure builds up. Toyota issued a service bulletin for this noise and replaces the gear.
- What to do
- This is not an emergency, but have it checked so a dealer can confirm it is the timing gear and not something more serious. Keep up with oil changes using the correct 0W-20 oil.
Clunk from the front suspension over bumps
- What you'll notice
- A clunk or knock from the front of the car when driving over bumps or rough pavement.
- Why it happens
- Toyota issued service bulletins for front suspension clunk on 2008-2012 xDs, and extended warranty coverage on a front lower control arm bolt.
- What to do
- Have the front suspension inspected so any loose bolt or worn part is found. Ask a Toyota dealer about the bulletin and whether any coverage still applies.
Noise or vibration from an engine mount when accelerating
- What you'll notice
- A groan, thump or vibration felt in the cabin when you accelerate or shift gears.
- Why it happens
- Toyota issued a service bulletin for abnormal noise and vibration from the side engine mount when accelerating. Noise or vibration on acceleration is one of the problems RepairPal lists most for the xD.
- What to do
- Have the engine mounts inspected. A worn mount is not dangerous right away but can let the engine move more and strain other parts.
Water on the passenger floor from a blocked A/C drain
- What you'll notice
- Wet carpet or a puddle on the front passenger floor, usually after running the air conditioning.
- Why it happens
- The tube that drains condensation from the A/C can clog with debris or insect nests, so water backs up into the cabin. Toyota issued bulletins for this on 2008-2012 xDs, and again for insect nests.
- What to do
- Have the A/C drain tube cleared, and dry the carpet so it doesn't get moldy. The fix is usually quick and cheap.
Musty smell from the air vents
- What you'll notice
- A musty or sour smell from the vents, mostly when the A/C or fan first comes on.
- Why it happens
- Moisture left on the A/C evaporator lets mold and bacteria grow. Toyota issued a bulletin on HVAC odors and how to reduce them.
- What to do
- Replace the cabin air filter and ask a shop about an evaporator cleaning. Turning off the A/C a few minutes before you park, while leaving the fan on, helps the system dry out.
Clear coat cracking or peeling
- What you'll notice
- The shiny top layer of paint turns cloudy, cracks or flakes off, usually on the roof, hood and other sun-facing panels.
- Why it happens
- Clear coat failure is the top body complaint for the 2009 xD and shows up on 2008 cars too. Owners report Toyota declining to cover it.
- What to do
- This is cosmetic, but bare paint will eventually rust. Get a body shop quote to refinish the worst panels, and keep the car waxed or parked out of the sun.
Load capacity label missing or wrong (recall)
- What you'll notice
- No symptom. The door-jamb label showing how much weight the car can carry may be missing or show the wrong numbers, mostly on cars with dealer-added accessories.
- Why it happens
- Labels on some cars didn't meet federal requirements, which could lead an owner to overload the car. Recalls 10V-035 and 10V-036 replace the labels.
- What to do
- Check your VIN for open recalls; the label is replaced for free. Until then, don't load the car beyond what the owner's manual allows.
Clicking from a worn CV axle
- What you'll notice
- A clicking or popping noise when turning sharply, or grease thrown around the inside of a front wheel from a torn rubber boot.
- Why it happens
- The front axle joints and their rubber boots wear with age. A torn boot lets dirt in and grease out, and the joint then wears quickly.
- What to do
- Have the axles and boots inspected. Catching a torn boot early can save the joint; a clicking joint usually means the axle should be replaced.
Check engine light from the fuel vapor (EVAP) canister
- What you'll notice
- The check engine light comes on with an evaporative emissions code, and it comes back after the gas cap is replaced.
- Why it happens
- Owners report water getting into the charcoal canister that stores fuel vapors, or the canister failing, which causes vapor-system leak codes.
- What to do
- Make sure the gas cap clicks tight first. If the light returns, have a smoke test done to find the leak. It's not urgent, but the car may fail an emissions test.
Repair prices for your 2008 Scion xD
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace water pump and drive belt
- Head gasket repair, or replace engine with a used unit
- Reseal timing chain cover
- Diagnose oil consumption and update engine computer per bulletin
- Replace camshaft timing (VVT) gear
- Diagnose no-start and update engine computer per bulletin
- Replace ignition coil (and spark plugs)
- Replace alternator
- Replace rear wheel speed sensor or wiring
- Clear A/C evaporator drain tube
- Refinish affected panels
- Replace starter motor
- Replace one wheel bearing or hub assembly
- Replace clutch kit and resurface flywheel
- Replace front CV axle
- Smoke test and replace charcoal canister
- Replace rear calipers, pads and rotors
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Inspect and regrease or replace power window master switchNo charge if your vehicle is included
- Inspect and replace front seat railNo charge if your vehicle is included
- Install redesigned intake air connectorNo charge if your vehicle is included
- Replace load capacity labelNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Checking the NHTSA recall database…