Toyota Corollaproblems, repair costs and recalls
Problems reported across 1996–2026. Pick your model year below to see what applies to your vehicle.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems
36 documented issues across all years, most serious first.
Airbag may deploy after a jolt (recall 97V-043)
- What you'll notice
- Usually no warning beforehand; the front airbag could go off after a hard bump or impact to the car that is not a real crash.
- Why it happens
- The airbag control computer on some cars could read a sharp mechanical shock as a collision.
- What to do
- Ask the dealer to confirm the recall applies to the VIN and have a Toyota dealer confirm the airbag computer repair was done before relying on the car.
Unexpected airbag deployment from the airbag control module (recalls 13V-029, 15V-043)
- What you'll notice
- An airbag warning light may come on, and in rare cases a front airbag can go off without a crash.
- Why it happens
- Electrical noise could reach the airbag control module and cause a short in its firing circuits.
- What to do
- Check the VIN for these recalls and have the module replaced at a Toyota dealer before driving the car regularly.
Passenger airbag inflator can rupture (do-not-drive advisory, recall 15V-286)
- What you'll notice
- No warning signs; the danger only shows up in a crash that sets off the passenger airbag.
- Why it happens
- These cars used Takata inflators whose propellant breaks down with age and heat, and some 2003-2004 Corollas are under a do-not-drive warning.
- What to do
- Do not drive the car until a VIN recall check is done and the airbag has been replaced. Toyota dealers can arrange towing or a mobile repair.
Engine computer can fail and stall the engine (recall 10V-384)
- What you'll notice
- Check engine light, harsh or delayed shifting, hard starting, or the engine stalling while driving.
- Why it happens
- Solder joints on the engine control module circuit board could crack over time.
- What to do
- Have the VIN checked for this recall and get the module inspected or replaced. If the engine stalls or shifts badly, limit driving until it is repaired.
Accelerator pedal sticks or gets trapped (recalls 10V-017, 10V-023)
- What you'll notice
- The gas pedal is hard to press, comes back up slowly, stays partly down, or gets caught under the floor mat and holds the engine at high speed.
- Why it happens
- Wear in the pedal's friction mechanism could make it stick, and loose or wrong floor mats could trap the pedal.
- What to do
- Confirm both recalls were completed and use only properly secured, correct-fit floor mats. If the pedal sticks, shift to neutral, brake firmly and pull over.
Brake booster vacuum port can freeze in extreme cold (recall 09V-338)
- What you'll notice
- A hard brake pedal and longer stopping distances in very cold weather.
- Why it happens
- Water vapor could freeze inside the vacuum port feeding the brake booster and block it.
- What to do
- Have a dealer confirm the intake connector repair was done, especially in cold-climate states. Do not drive if the brake pedal is unusually hard.
Airbag light from a damaged spiral cable (recall 14V-168)
- What you'll notice
- The airbag warning light comes on, and the horn or steering wheel buttons may stop working.
- Why it happens
- The flat cable inside the steering column that connects the driver airbag could be damaged as the wheel turns.
- What to do
- Have the recall repair done right away; with the light on, the driver airbag may not deploy in a crash.
Power window master switch can overheat (recalls 12V-491, 15V-689)
- What you'll notice
- A sticky or intermittent driver's window switch, a burning smell, or smoke from the driver's door panel.
- Why it happens
- The grease on the switch contacts was applied unevenly, which can lead to heat and melting inside the switch.
- What to do
- Stop using the switch and have the recall repair done right away if you smell burning; this is a fire risk.
Low-pressure fuel pump can fail (recalls 20V-012, 20V-682)
- What you'll notice
- Rough running, check engine light, trouble starting, or the engine stalling while driving.
- Why it happens
- The low-pressure fuel pump supplied for these cars could stop working, cutting fuel to the engine.
- What to do
- Check the VIN for these recalls and get the pump replaced. A stall at speed is dangerous, so limit driving until it is fixed.
CVT torque converter failure (recall 18V-901)
- What you'll notice
- Loss of power, the car will not move, or it stalls; affected cars are some 2019 Corolla Hatchbacks with the CVT.
- Why it happens
- Blades inside the torque converter pump could break loose.
- What to do
- Check the VIN for this recall and do not keep driving a car that loses power; have it towed to a Toyota dealer.
Rear seat belts may not lock in a second impact (recall 19V-877)
- What you'll notice
- No warning signs in normal use.
- Why it happens
- The rear seat belt locking mechanism might not hold during a crash that involves more than one impact.
- What to do
- Have the VIN checked and the belt assemblies replaced if needed before carrying rear passengers.
Passenger airbag may switch off with an adult seated (recall 23V-865)
- What you'll notice
- The passenger airbag OFF light stays lit with an adult in the seat, or the airbag warning light comes on.
- Why it happens
- The occupant sensor in the front passenger seat can short and fail to detect the passenger.
- What to do
- Have the recall inspection done; until then, the front passenger may not be protected by the airbag.
Driver airbag spiral cable weld can separate (recalls 23V-480, 25V-040)
- What you'll notice
- Airbag warning light on, and possibly a dead horn.
- Why it happens
- A weld inside the steering spiral cable may break, cutting the connection to the driver airbag.
- What to do
- Get the recall inspection done promptly; with the light on, the driver airbag may not deploy.
Intermediate steering shaft can crack (recall 24V-878)
- What you'll notice
- Vibration or extra play in the steering wheel, or clunking when turning.
- Why it happens
- A joint in the intermediate steering shaft may have cracked during manufacturing and could separate.
- What to do
- Stop driving if the steering feels loose and have the shaft replaced under the recall.
Hybrid can lose power brake assist while turning (recall 24V-708)
- What you'll notice
- The brake pedal suddenly feels hard and the car takes more effort and distance to stop, most likely when braking in the middle of a turn. Brake and stability warning lights may come on.
- Why it happens
- A software error in the brake control computer on the Corolla Hybrid can shut off power brake assist under certain cornering conditions. The regular brakes still work, but need much more pedal force.
- What to do
- Check your VIN for this recall and book the free software update at a Toyota dealer as soon as you can. If the pedal goes hard, press firmly, stop safely and have the car checked before driving on.
Cruise control may not hold the set speed (recall 96E-001)
- What you'll notice
- With cruise control on, the car can speed up past the speed you set instead of holding it.
- Why it happens
- The cruise control assembly can fail in a way that lets the throttle stay open.
- What to do
- Switch the cruise control off and leave it off until a shop replaces the assembly; the recall remedy was a free replacement.
Airbag computer may fail in a crash (recall 20V-024)
- What you'll notice
- Usually nothing shows beforehand, though an airbag warning light can appear. In some crashes the airbags or belt pretensioners may not fire.
- Why it happens
- Electrical noise can upset the airbag control unit, so it does not react to the crash sensors as designed.
- What to do
- Have the VIN checked and the recall done; the dealer inspects the control unit and adds a noise filter. The repair is free.
Excessive oil consumption
- What you'll notice
- The oil level drops noticeably between changes, blue-gray smoke at startup or on acceleration, and sometimes misfires or a check engine light.
- Why it happens
- Carbon builds up in the oil control rings on this engine, so the rings stick and let oil get burned in the cylinders.
- What to do
- Check the dipstick at every fill-up and top off as needed; running the engine low on oil can ruin it. A shop can confirm ring sticking and advise on a ring cleaning or rebuild.
Door glass can come loose from the window regulator (recall 08V-162)
- What you'll notice
- A window that rattles, sits crooked, will not go up properly, or drops down inside the door.
- Why it happens
- The bolts holding the door glass to the regulator could loosen over time.
- What to do
- Have a dealer check the VIN and install the replacement bolts; a loose window can fall into the door.
Oil leak at the timing chain tensioner or valve cover gasket
- What you'll notice
- Oil wetness on the back side of the engine near the firewall, oil drips under the car, or a burning oil smell after driving.
- Why it happens
- The gasket behind the timing chain tensioner and the valve cover gasket harden and shrink with age on this engine.
- What to do
- Have the leak source confirmed and the gasket replaced, and keep an eye on the oil level until it is fixed.
Electric power steering drifts or wanders
- What you'll notice
- The car drifts to one side or wanders at highway speed and needs constant small steering corrections.
- Why it happens
- The electric power steering assist could be tuned or behave unevenly, which NHTSA investigated; Toyota offered a free steering repair program for these years.
- What to do
- Ask a Toyota dealer whether the car qualifies for the steering repair program and have the alignment and steering system checked.
Oil consumption on the 2.4L engine (XRS)
- What you'll notice
- The oil level drops between changes, and the low-oil light may come on before the next service.
- Why it happens
- The piston rings on this engine can let oil slip past into the combustion chamber; Toyota issued a warranty enhancement (ZE7) for it.
- What to do
- Check oil often and ask a Toyota dealer about the ZE7 program and an oil consumption test.
Water pump leak or noise
- What you'll notice
- Pink coolant drips or crust on the passenger side of the engine, a whining or grinding sound, or a dropping coolant level.
- Why it happens
- The water pump bearing and seal wear out earlier than expected on this engine.
- What to do
- Replace the pump at the first sign of leaking and watch the temperature gauge; stop driving if the engine overheats.
Front wheel bearing hum
- What you'll notice
- A humming or growling sound that rises with speed and may change when turning.
- Why it happens
- Front wheel bearings are one of the most frequently replaced parts reported on these Corollas.
- What to do
- Have the bearings checked soon; a badly worn bearing can overheat and affect steering.
Windshield wiper switch can short out (recall 13V-505)
- What you'll notice
- Wipers that stop working or work only on some settings.
- Why it happens
- A short circuit could develop inside the wiper switch.
- What to do
- Have the switch replaced under the recall; do not drive in rain or snow without working wipers.
Parking brake malfunction message on the display
- What you'll notice
- A parking brake malfunction warning shows up on the information display, often with a warning light, even when the brake seems to hold the car normally.
- Why it happens
- The electric parking brake control picks up a stored fault (code C059746); Toyota covers the condition in a service bulletin with updated control software and, where needed, parts.
- What to do
- Have the car scanned and ask the shop about the bulletin for this message, and leave the car in Park on a slope until it is sorted.
Check engine light for catalyst efficiency (P0420)
- What you'll notice
- A steady check engine light with code P0420, usually with no change in how the car drives.
- Why it happens
- The catalytic converter or the downstream oxygen sensor wears out with age and mileage; oil burning can speed this up.
- What to do
- Have the code confirmed and both oxygen sensors and any exhaust leaks checked before buying a new converter.
Lean code (P0171) from a vacuum leak or dirty airflow sensor
- What you'll notice
- Check engine light with P0171, rough idle, hesitation, a hissing sound under the hood, or occasional stalling.
- Why it happens
- The intake manifold gasket can leak air, or the mass airflow sensor gets dirty and under-reads incoming air.
- What to do
- Have a shop smoke-test for vacuum leaks and clean or test the airflow sensor before replacing other parts.
Brief rattle at cold start from the cam timing gear (TSB T-SB-0087-09)
- What you'll notice
- A short knocking or rattling noise for a second or two right after starting a cold engine.
- Why it happens
- The variable valve timing gear on the camshaft could be faulty and let the timing parts rattle until oil pressure builds.
- What to do
- Mention the bulletin to a Toyota dealer; the noise usually does not harm the engine right away but the gear can be replaced.
Starter or alternator failure
- What you'll notice
- A single click with no crank, or a battery light with dimming lights while driving.
- Why it happens
- The starter and alternator are frequent replacement parts on this generation as mileage builds.
- What to do
- Get a free battery and charging system test before buying parts.
EVAP leak code from a misplaced fuel filler neck (TSB T-SB-0086-16)
- What you'll notice
- Check engine light with code P0455 or P0456 even with the gas cap tight.
- Why it happens
- The fuel filler neck can sit out of position so the gas cap does not seal fully.
- What to do
- Ask a Toyota dealer to check the filler neck position per the bulletin before replacing EVAP parts.
Headlight aim markings missing (recall 26V-110)
- What you'll notice
- Headlights that seem aimed too high or low, or glare complaints from other drivers.
- Why it happens
- Aim markings were left off the headlight assemblies, so they may not be set correctly.
- What to do
- Have a dealer check the VIN; the fix is new headlight assemblies.
Buzz or rattle from the right engine mount
- What you'll notice
- A buzz, rattle or vibration comes up through the floor, console or steering wheel at idle and light acceleration, and is usually worst when the engine is cold.
- Why it happens
- The right-hand engine mount insulator passes engine vibration into the body instead of soaking it up; Toyota released an improved mount for the condition.
- What to do
- Not harmful, but have the mount looked at on your next visit rather than hunting for a loose trim piece.
Rattle from the headliner over the front seats
- What you'll notice
- A light rattle or tapping comes from the roof lining above the front seats over bumps and rough pavement.
- Why it happens
- The headliner is not held tightly enough against the roof on some Japan-built sedans, so it taps as the body flexes; the fix is extra padding and clips.
- What to do
- Cosmetic only - mention it at a service visit and have the headliner secured.
Engine maintenance message keeps appearing on the cluster
- What you'll notice
- An engine maintenance message asking you to visit the dealer shows up on the instrument cluster, usually with nothing else wrong in how the car drives.
- Why it happens
- The engine control software reports the condition earlier than intended on these direct-injection engines; Toyota addresses it with a reprogramming bulletin.
- What to do
- Check your oil level first, then have the engine computer reprogrammed under the bulletin so you can trust the message next time.
Clicking from the front wheels at full steering lock
- What you'll notice
- A click or clunk repeats from the front of the car when you turn the wheel all the way and pull away, as in a U-turn or a tight parking manoeuvre.
- Why it happens
- Parts in the front suspension and steering can bind against each other at full lock under power; Toyota describes the inspection and fix in a bulletin.
- What to do
- Mention the noise at a service visit so the suspension and driveshaft joints get checked while it is still only a noise.
Repair prices for your Toyota Corolla
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Repair or replace airbag sensor computer
- Replace pistons and rings
- Replace airbag control module
- Replace passenger front airbag
- Reattach door glass to regulator with new bolts
- Replace catalytic converter
- Replace valve cover gasket or tensioner O-ring
- Smoke-test for vacuum leaks, clean airflow sensor, fix leak
- Replace engine control module
- Modify or replace accelerator pedal assembly
- Replace intake vacuum connector for brake booster
- Replace steering wheel spiral cable
- Replace steering column with power steering motor
- Replace intake cam timing gear
- Replace driver's master window switch
- Replace water pump and refill coolant
- Replace alternator
- Replace front wheel bearing
- Replace windshield wiper switch
- Reposition fuel filler neck and clear EVAP code
- Replace in-tank fuel pump
- Replace CVT torque converter
- Replace rear seat belt assemblies
- Replace passenger seat occupant sensor
- Replace intermediate steering shaft
- Replace both headlight assemblies
- Update skid control computer software
- Replace cruise control actuator assembly
- Inspect airbag control unit and add noise filter
- Reprogram parking brake control, replace actuator if needed
- Replace right engine mount insulator
- Secure headliner with pads and clips
- Reprogram engine control module
- Inspect and service front suspension and axle joints
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Pick a model year to see its safety recalls.