Toyota Matrixproblems, repair costs and recalls
Problems reported across 2003–2013. Pick your model year below to see what applies to your vehicle.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems
31 documented issues across all years, most serious first.
Heavy oil burning on the 2.4L engine
- What you'll notice
- You need to add oil between changes, sometimes a quart every 1,000 miles or less. Blue smoke at startup, fouled spark plugs or a low-oil warning can follow.
- Why it happens
- The piston oil rings on the 2.4L engine of this era can clog with carbon and stop scraping oil off the cylinder walls, so the engine burns it. Toyota later changed the piston design and set up a warranty enhancement program (ZE7) for affected 2009 Matrix models.
- What to do
- Check the oil level every fill-up so it never runs low. Ask a Toyota dealer to run an oil consumption test and check whether your car is covered by the ZE7 program or a goodwill repair. The usual fix is new pistons and rings.
Engine computer can crack and stall the engine (recall)
- What you'll notice
- The check engine light comes on, the automatic shifts harshly, the car won't start, or the engine shuts off while driving. Code P2716 is often stored.
- Why it happens
- Some engine control modules had circuit board solder joints or parts that could crack over time. Toyota recall 10V-384 replaces the module on 2005-2008 Matrix models with the base 1.8L engine.
- What to do
- Have a Toyota dealer check your VIN for recall 10V-384. The module replacement is free. If the car stalls, pull over safely and have it towed rather than driving on.
Passenger airbag inflator can rupture, 2003-2008 (Takata recall)
- What you'll notice
- Usually no warning at all. In a crash, the passenger airbag inflator can burst and throw metal fragments into the cabin.
- Why it happens
- The Takata passenger airbag inflators in these cars break down after years of heat and humidity. Toyota has issued several recalls, including 15V-285, 15V-286 and 18V-025, to replace them.
- What to do
- Treat this as urgent. Ask a Toyota dealer to confirm the recall applies to your VIN and get the free replacement. Until it is done, keep people out of the front passenger seat if you can.
Passenger airbag inflator can rupture, 2009-2013 (Takata recall)
- What you'll notice
- No warning before a crash. If the passenger airbag deploys, the inflator can burst and spray metal pieces.
- Why it happens
- These Matrix models also use Takata passenger inflators that degrade with age, heat and humidity. They are covered by recalls such as 16V-340, 18V-024 and 19V-005.
- What to do
- Check your VIN for open airbag recalls and book the free repair. Avoid using the front passenger seat until the new inflator is fitted.
Rod knock and sudden engine failure
- What you'll notice
- A knock or rapping noise that gets louder with throttle, ticking that turns into a rattle, then the engine seizes or a rod breaks through the block. Some owners saw heavy oil use first.
- Why it happens
- Owners of early Matrix models report connecting rod bearing failures, often around 90,000-140,000 miles. Running the 1.8L engine low on oil, which is easy to do if it is burning oil, starves the bearings.
- What to do
- If you hear a new knock, stop driving and check the oil level right away. A shop can confirm with an oil pressure test. Once a bearing has spun, a used or remanufactured engine is usually the realistic fix.
Automatic transmission slipping or failing
- What you'll notice
- Delayed engagement, slipping between gears, flaring revs or the car losing drive altogether, usually at around 90,000-140,000 miles.
- Why it happens
- The 4-speed automatic in early Matrix models wears internally. Transmission failure is one of the most reported and costly problems for the 2003-2005 model years.
- What to do
- Check the fluid level and condition. If it is dark or smells burnt, or the transmission is slipping, get a diagnosis before it fails completely. A used or remanufactured transmission is the usual fix.
Airbags may deploy without a crash (recall)
- What you'll notice
- The airbag light may be on, or the airbags or seat belt pretensioners go off without a crash.
- Why it happens
- The airbag control module could be affected by electrical noise and trigger the airbags unexpectedly. Recalls 13V-029 and 15V-043 cover these cars.
- What to do
- Check for open recalls with your VIN and have the free fix done. Get any airbag warning light looked at promptly.
Sticking accelerator pedal (recall)
- What you'll notice
- The gas pedal feels sticky, returns slowly, or stays partly pressed after you lift your foot.
- Why it happens
- Wear inside the pedal assembly could make it stick. Recall 10V-017 adds a reinforcement bar or replaces the pedal.
- What to do
- If the pedal sticks, shift to neutral, brake firmly and pull over. Check your VIN for the free recall repair.
Floor mat can trap the gas pedal (recall)
- What you'll notice
- The gas pedal gets caught under the driver's floor mat and the car keeps accelerating.
- Why it happens
- An unsecured or wrong floor mat can slide forward and pin the pedal. Recall 10V-023 reshapes the pedal and changes the mats.
- What to do
- Remove extra or loose mats and use only mats that clip in. Have the recall work checked by VIN.
Driver's power window switch can overheat (recall)
- What you'll notice
- The driver's window switch feels sticky or hot, stops working, or gives off a burning smell or smoke.
- Why it happens
- The master window switch could lack proper lubrication, letting it short out and overheat. Recalls 12V-491 and 15V-689 cover these years.
- What to do
- If it smells hot or melts, stop using it and park outside. The dealer applies special grease or replaces the switch for free.
Airbag light from a damaged steering wheel cable (recall)
- What you'll notice
- The airbag warning light comes on, and the horn may stop working.
- Why it happens
- The flat cable inside the steering column that connects the driver's airbag can be damaged by turning, which can disable the airbag. Recall 14V-168 fixes it.
- What to do
- Have the free recall done. An airbag light means the airbag may not work in a crash.
Hard brake pedal in extreme cold (recall)
- What you'll notice
- In very cold weather the brake pedal feels hard and the car takes longer to stop.
- Why it happens
- Moisture in the brake booster vacuum port on the intake could freeze and block the vacuum the brakes need for power assist. Recall 09V-338 replaces the port.
- What to do
- Check your VIN for recall 09V-338 and have it done before winter.
Coolant leak from stripped head bolt threads
- What you'll notice
- Coolant slowly disappears with no visible leak, or you see coolant seeping near the back of the engine. Overheating can follow.
- Why it happens
- On the 2.4L engine, the head bolt threads in the aluminum block can pull out, letting the head gasket seal weaken and leak coolant.
- What to do
- Watch the coolant level and temperature gauge. A shop can confirm with a cooling system pressure test. The repair means installing thread inserts and a new head gasket, which is costly.
Airbags may not deploy in some crashes (recall)
- What you'll notice
- Usually no warning. The airbag light may come on in some cars.
- Why it happens
- The airbag control unit could be damaged by electrical noise in certain crashes, so the airbags and seat belt pretensioners may not deploy. Recall 20V-024 adds a noise filter.
- What to do
- Check your VIN and have the free repair done.
Oil burning on the 1.8L engine
- What you'll notice
- The oil level drops between changes, the low-oil light may come on, and you may see blue smoke at startup or get a catalytic converter code.
- Why it happens
- The base 1.8L engine (1ZZ-FE) in the first-generation Matrix is known for oil consumption caused by piston rings that stick with carbon. Long oil-change intervals make it worse.
- What to do
- Check the dipstick every couple of weeks and top up as needed. Change oil every 3,500-5,000 miles. If it uses more than a quart per 1,000 miles, get a compression and leak-down test before deciding on rings or an engine swap.
Manual transmission bearing noise or popping out of gear
- What you'll notice
- A rattle or whine from the gearbox when the clutch is engaged, grinding, or the shifter popping out of a gear.
- Why it happens
- Worn bearings in the manual transmission are a well-known weak spot of the first-generation Matrix. Manual-gearbox complaints far outnumber automatic ones for 2003 models.
- What to do
- Change the gear oil if it is overdue and have the noise checked. If it gets louder or the car jumps out of gear, a rebuild with new bearings or a used gearbox will be needed.
Clutch wearing out early
- What you'll notice
- The engine revs rise without the car speeding up, the clutch engages high in the pedal travel, or there is a burning smell after hills.
- Why it happens
- Owners report clutches on manual Matrix models wearing out at around 40,000-50,000 miles, well before most cars.
- What to do
- Have the clutch checked if it slips. Replacing the clutch disc, pressure plate and release bearing together, and resurfacing or replacing the flywheel, avoids repeat labor.
Whining from the rear differential (AWD)
- What you'll notice
- A whine from the back of the car that rises with speed, on all-wheel-drive models.
- Why it happens
- The rear differential on the AWD Matrix can wear and become noisy. Toyota issued a service bulletin for abnormal rear differential noise, but owners report it often appears after the warranty ended.
- What to do
- Have the rear differential fluid checked and changed. If the whine continues, a shop can confirm the source on a lift; replacing the differential is the common fix.
Check engine light for misfire or lean codes
- What you'll notice
- Check engine light with codes like P0171, P0300-P0304 or P0133. The engine may idle rough or hesitate.
- Why it happens
- A leaking intake manifold gasket (covered by Toyota bulletin EG045-07) lets in extra air, and a dirty or failed airflow sensor can cause the same lean condition.
- What to do
- A shop can smoke-test the intake for leaks and check the airflow sensor. The gasket is an affordable repair; cleaning or replacing the sensor is simple.
Check engine light for catalyst efficiency (P0420)
- What you'll notice
- Check engine light with code P0420. The car usually drives normally but may fail an emissions test.
- Why it happens
- On the 1.8L engine the catalytic converter wears out, and oil burning speeds that up. A failing rear oxygen sensor can set the same code.
- What to do
- Have a shop confirm the converter is the cause, not a sensor or exhaust leak. If the engine burns oil, fix that first or a new converter will fail too.
Starter motor failure
- What you'll notice
- You turn the key and hear a single click, or nothing, even though the lights work.
- Why it happens
- The starter motor wears out with age on both Matrix generations. Corroded battery terminals can cause the same symptom.
- What to do
- Clean the battery terminals and test the battery first. If the battery is fine, have the starter tested and replaced.
Door glass can come loose from the window regulator (recall)
- What you'll notice
- The front window binds, makes a grinding noise, tilts in the door or shatters when you use the switch.
- Why it happens
- Bolts holding the front door glass to the window regulator could loosen. Recall 08V-162 re-secures the glass.
- What to do
- Have a Toyota dealer check for recall 08V-162. Avoid using the window if the glass looks crooked.
Electric power steering drifts or wanders
- What you'll notice
- The car pulls or wanders on the highway and needs constant small corrections; some cars feel loose on center.
- Why it happens
- The electric power steering on 2009-2010 Corolla and Matrix models could cause drifting. After an NHTSA investigation, Toyota offered a steering fix for affected cars.
- What to do
- Have the alignment and tires checked first. If the problem stays, ask a Toyota dealer whether the steering update or column replacement applies to your car.
Water pump leak or noise
- What you'll notice
- Pink coolant drips on the passenger side of the engine, a low coolant level, or a grinding or squealing noise from the belt area.
- Why it happens
- The water pump seal and bearing wear out on the second-generation Matrix.
- What to do
- Top up with Toyota pink coolant and watch the temperature gauge. Replace the pump, and the drive belt at the same time, before it overheats the engine.
Misfire from a failed ignition coil
- What you'll notice
- Check engine light, sometimes flashing, with a code from P0301 to P0304. The engine shakes at idle or hesitates.
- Why it happens
- Ignition coils on the second-generation Matrix can fail with age and heat.
- What to do
- Have the misfire code read. Replacing the failed coil is easy and inexpensive; replace old spark plugs at the same time.
Alternator stops charging
- What you'll notice
- The battery warning light comes on while driving, lights dim, or the battery keeps going flat.
- Why it happens
- The alternator wears out on higher-mileage Matrix models.
- What to do
- Get a charging system test. If the alternator output is low, replace it before the battery drains and leaves you stuck.
Wheel bearing hum
- What you'll notice
- A humming or growling noise that rises with speed and may change when you turn.
- Why it happens
- Wheel bearings wear out at higher mileage on the second-generation Matrix.
- What to do
- Have a shop find which wheel it is. Replace the bearing before it gets loose.
Squeal or rattle from the drive belt tensioner
- What you'll notice
- A squeal at startup or a rattle from the front of the engine, often at idle.
- Why it happens
- The automatic drive belt tensioner on the first-generation Matrix wears out. Toyota released an updated part.
- What to do
- Have the tensioner and belt checked. Replace both at once; it is a quick job.
Brief rattle at cold start from the cam timing gear
- What you'll notice
- A loud rattle or chatter for one or two seconds right after a cold start, then the engine runs normally.
- Why it happens
- The variable valve timing gear on the intake camshaft can rattle before oil pressure builds. Toyota bulletin T-SB-0087-09 replaces the gear.
- What to do
- Not an emergency, but have it checked while the noise is happening. The gear replacement fixes it.
Oil leak from the timing chain cover
- What you'll notice
- Oil wetness on the passenger side front of the engine and small spots under the car.
- Why it happens
- The sealant on the 1.8L engine's timing chain cover can start to seep. A leaking oil pressure switch is a cheaper look-alike.
- What to do
- Have a shop clean the area and find the exact source. Small seeps can be watched; a real leak needs the cover resealed.
Rear brakes wearing early or calipers sticking
- What you'll notice
- Grinding from the rear, the car pulling, a hot wheel or the brakes dragging.
- Why it happens
- Rear brakes on these cars wear prematurely without regular service, and rear calipers on disc-brake models can seize.
- What to do
- Have the brakes cleaned and adjusted once a year. Replace a seized caliper and worn pads or shoes.
Repair prices for your Toyota Matrix
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace pistons and rings
- Replace engine with used or remanufactured unit
- Replace automatic transmission with used or remanufactured unit
- Rebuild manual transmission with new bearings
- Replace clutch kit and resurface flywheel
- Replace rear differential
- Replace drive belt tensioner and belt
- Replace intake manifold gasket or airflow sensor
- Replace catalytic converter
- Replace starter motor
- Replace steering column with power steering motor
- Replace intake cam timing (VVT) gear
- Install head bolt thread inserts and new head gasket
- Replace water pump, belt and refill coolant
- Reseal timing chain cover
- Replace ignition coil and spark plugs
- Replace alternator
- Replace one wheel bearing/hub
- Service rear brakes and replace a seized caliper
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Replace engine control moduleNo charge if your vehicle is included
- Replace passenger airbag inflatorNo charge if your vehicle is included
- Install airbag control module noise filter or replace moduleNo charge if your vehicle is included
- Re-secure door glass to regulator with new boltsNo charge if your vehicle is included
- Install pedal reinforcement or replace pedalNo charge if your vehicle is included
- Reshape pedal and replace floor matsNo charge if your vehicle is included
- Grease or replace power window master switchNo charge if your vehicle is included
- Replace steering wheel spiral cableNo charge if your vehicle is included
- Replace brake booster vacuum portNo charge if your vehicle is included
- Install noise filter on airbag control unitNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Pick a model year to see its safety recalls.