Volvo S80problems, repair costs and recalls
Problems reported across 1999–2016. Pick your model year below to see what applies to your vehicle.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems
35 documented issues across all years, most serious first.
Automatic transmission slips, shudders or fails
- What you'll notice
- Slipping between gears, shuddering, harsh or delayed shifts, a whine when accelerating, or a 'Transmission Service Urgent' message. Some cars stop moving altogether.
- Why it happens
- The automatic transmissions in the first-generation S80, especially the GM-built unit used in early T6 models, are its most common expensive failure. Owners report worn internals, shift solenoid faults and full failures, often between 50,000 and 120,000 miles. 1999 is considered the worst year.
- What to do
- Check the fluid level and condition and have a Volvo specialist read the transmission codes. Ask about software updates first; a solenoid or valve body repair may avoid a full rebuild.
Throttle module causes stalling and limp mode
- What you'll notice
- Rough idle, stalling in traffic, sudden loss of power, a no-start, or a warning light with the car in reduced-power limp mode.
- Why it happens
- Early S80s use an electronic throttle module whose internal contacts wear and get dirty. Volvo paid for cleanings and many replacements, and changed the design and supplier during the 2002 model year.
- What to do
- Have the throttle codes read. Cleaning sometimes helps, but a worn module needs replacing. Ask a Volvo dealer whether any goodwill coverage applies to your car.
Driver airbag inflator can rupture (recall)
- What you'll notice
- Usually no symptoms until a crash.
- Why it happens
- The driver's airbag inflator propellant can degrade, so the inflator may burst and throw metal fragments (recalls 20V-681 and 21V-766).
- What to do
- Check your VIN for open recalls and get the free airbag replacement right away.
Engine burns oil from piston ring wear
- What you'll notice
- Needing to add oil between changes, white or blue exhaust smoke, and a rough idle.
- Why it happens
- Six-cylinder engines built before 2012 used pistons and rings that let oil burn. Volvo later redesigned them.
- What to do
- Track oil use carefully and keep it topped up. If consumption is severe, ask a Volvo dealer for an oil consumption test.
Front seat belt anchor cable can break (recall)
- What you'll notice
- Usually no symptoms.
- Why it happens
- The steel cable that connects the seat belt to the front seats can wear from fatigue and break, so the belt may not hold you in a crash (recall 20V-378).
- What to do
- Check your VIN and get the free cable replacement.
Cooling fan may stop and engine can overheat (recall)
- What you'll notice
- Temperature gauge rising, overheating warning.
- Why it happens
- A software error in the fan control module can stop the cooling fan (recall 09V-218).
- What to do
- Stop if it overheats and get the free software update.
Fuel pump may not start and engine stalls (recall)
- What you'll notice
- The engine stalls or won't start.
- Why it happens
- Central electronic module software can fail to signal the fuel pump module (recall 09V-343).
- What to do
- Get the free software update.
Driver airbag clockspring connector fault (recall)
- What you'll notice
- An airbag (SRS) warning light.
- Why it happens
- An intermittent fault in the driver airbag clockspring connector means the airbag may not deploy correctly (recall 10V-489).
- What to do
- Get the free repair.
Engine can stall suddenly from software fuel cut-off (recall)
- What you'll notice
- The engine can shut off while driving.
- Why it happens
- Fuel cut-off calibration in the engine computer was too sensitive (recall 10V-579).
- What to do
- Get the free engine and transmission software update.
Engine can stall when coasting from transmission software (recall)
- What you'll notice
- RPM drops and the engine may stall when coasting to a stop.
- Why it happens
- Transmission software may not downshift while coasting (recall 12V-317).
- What to do
- Get the free transmission software update.
Seat wiring can disconnect and affect airbags (recall)
- What you'll notice
- An airbag warning light, especially after moving the seat.
- Why it happens
- A wiring harness under the front seats may not be clipped to the frame and can come apart (recall 12V-075).
- What to do
- Get the free inspection and repair.
Wipers run nonstop and lights can fail (recall)
- What you'll notice
- Wipers run continuously; turn signals, high beams or headlight switch stop working.
- Why it happens
- Central electronic module software fault on cars with keyless ignition (recall 13V-377).
- What to do
- Get the free CEM software update.
ABS module fails and turns on warning lights
- What you'll notice
- ABS, brake and traction (TRACS/STC) warning lights come on, sometimes on and off, and often worse in cold weather. The anti-lock system may stop working.
- Why it happens
- Solder joints on the ABS control module's circuit board crack over time and lose contact.
- What to do
- Normal brakes still work, but ABS may not. Have the codes read and rule out a wheel speed sensor first; the module can usually be rebuilt rather than replaced.
Clogged PCV oil trap causes oil leaks
- What you'll notice
- Oil leaks around the engine, seals pushed out, oil smoke or pressure at the dipstick, whistling at idle, or higher oil use.
- Why it happens
- The crankcase ventilation (PCV) oil trap and hoses clog with sludge. Pressure then builds inside the engine and pushes oil past seals. Breather box seal leaks are common on the T6.
- What to do
- Have the PCV system checked and cleaned or replaced, ideally around 100,000 miles. Fixing it early can prevent costly seal and turbo damage.
Worn front control arm bushings
- What you'll notice
- Clunking over bumps, loose or wandering steering, vibration when braking, or uneven tire wear.
- Why it happens
- The rubber bushings in the front lower control arms tear and wear out at higher mileage. Tie rods and ball joints wear too.
- What to do
- Have the front end inspected. Replace worn arms or bushings in pairs and get an alignment.
Ignition coil failure causes misfires
- What you'll notice
- A check engine light, rough running or shaking, and loss of power.
- Why it happens
- Individual ignition coils fail on the six-cylinder engines and are often replaced one at a time.
- What to do
- Have the misfire code read to find the cylinder and replace that coil. Don't drive long with a flashing check engine light.
Radiator and coolant hose leaks
- What you'll notice
- Coolant puddles, a sweet smell, a low coolant warning, or the temperature gauge climbing.
- Why it happens
- Plastic radiator necks, hoses and cores crack with age on early cars.
- What to do
- Top up with the correct coolant and have it pressure tested. Stop driving if the engine overheats.
Turbo oil return line seals leak
- What you'll notice
- Oil dripping under the engine, oil smell or smoke from the exhaust area.
- Why it happens
- The O-rings on the turbo oil drain tubes harden and leak on the twin-turbo T6.
- What to do
- Have the leak traced. Replacing both drain tube O-rings takes several hours but is much cheaper than a turbo.
Central electronic module (CEM) faults
- What you'll notice
- Random problems with windows, locks, wipers, lights or gauges, warning lights, or a no-start from the immobilizer.
- Why it happens
- The CEM controls most body electronics. Water leaks, corroded connections or a weak battery can make it misbehave.
- What to do
- Test the battery and grounds first and fix any water leak. A Volvo specialist can repair or reprogram the CEM.
Oil leaks from vacuum pump and valve cover
- What you'll notice
- Oil on the side or front of the engine, burning oil smell, or drips under the car.
- Why it happens
- The vacuum pump seals on the 3.2L blow out, and the valve cover sealant ages on both six-cylinder engines.
- What to do
- Have the leak cleaned and traced. Reseal the vacuum pump or valve cover before oil reaches belts or exhaust.
Water pump and accessory pulley wear
- What you'll notice
- Coolant leaks, a whirring noise or wobbling pulley at the front of the engine, or overheating.
- Why it happens
- On the six-cylinder engines the accessory drive pulley wears and strains its bearings, and early water pumps leak. Cooling hose O-rings also dry out.
- What to do
- Have the belt drive and water pump inspected at higher mileage, and fix coolant leaks before the engine overheats.
AWD system disabled warning (Haldex pump)
- What you'll notice
- An 'AWD Disabled Service Required' message, AWD warning light, and the car drives in front-wheel drive only.
- Why it happens
- The Haldex rear coupling's pump and filter clog with clutch material, or the pump or its control module fail. Mismatched tires can also trigger it.
- What to do
- Have the AWD codes read. A fluid and filter service often fixes it; keep all four tires matched.
Adaptive (Four-C) shocks leak or fail
- What you'll notice
- A harsher or bouncier ride, a suspension warning, or leaking shocks.
- Why it happens
- Electronically adjustable shocks on these cars wear out and are expensive to replace.
- What to do
- Have the shocks inspected. Non-adaptive conversion kits can cut the cost on older cars.
A/C compressor fails
- What you'll notice
- The A/C blows warm, or there's a grinding or rumbling from the compressor.
- Why it happens
- Compressor bearings and compressors fail on these years.
- What to do
- Turn the A/C off if it's noisy and have it checked before the bearing seizes.
V8 valve cover oil leaks
- What you'll notice
- Burning oil smell, smoke from the engine bay, or oil on the engine.
- Why it happens
- Valve cover gaskets on the 4.4L V8 leak with age.
- What to do
- Have the leak traced and the gaskets replaced before oil drips onto the exhaust.
Wipers may stop or run by themselves (recall)
- What you'll notice
- Wipers don't work or turn on without being switched on.
- Why it happens
- Diagnostic software in the central electronic module can upset wiper operation (recall 09V-139).
- What to do
- Have the free CEM software update done.
False tire pressure service message (recall)
- What you'll notice
- A 'TPMS Service Required' message after driving, and no warning for low tires.
- Why it happens
- A software error disables low-pressure warnings (recall 12V-415).
- What to do
- Check tire pressures by hand and get the free reprogramming.
Starter fuse can blow with stop/start (recall)
- What you'll notice
- The engine won't restart after an auto stop.
- Why it happens
- The starter fuse may blow with stop/start use (recall 15V-555).
- What to do
- Get the free higher-rated fuse installed.
Worn struts and strut mounts
- What you'll notice
- A bouncy or floaty ride, knocking over bumps, or oil on the strut body.
- Why it happens
- The struts and their upper mounts wear out on high-mileage cars and are among the most reported S80 repairs.
- What to do
- Have the struts and mounts checked. Replace them in pairs on the same axle.
Worn engine mounts cause vibration
- What you'll notice
- Extra vibration at idle or in gear, and a clunk when accelerating or shifting.
- Why it happens
- The right-side and upper engine mounts wear out or leak their fluid.
- What to do
- Have the mounts inspected. A worn torque or upper mount is fairly cheap to replace.
Xenon headlight fails or aims wrong
- What you'll notice
- One headlight goes out or flickers, or a headlight warning appears.
- Why it happens
- Bulbs, HID ballast modules and leveling parts fail on higher-mileage cars.
- What to do
- Check the bulb first, then the ballast module. Use matching parts so beams stay correctly aimed.
A/C stops blowing cold
- What you'll notice
- The A/C blows warm, cuts in and out, or the compressor clutch doesn't engage.
- Why it happens
- Compressor clutches, compressors and refrigerant lines wear out.
- What to do
- Have the system checked for leaks and pressures before recharging.
Hissing at idle from torn PCV diaphragm
- What you'll notice
- A hiss or whistle at idle, rough idle, or a check engine light.
- Why it happens
- The rubber diaphragm in the T6's PCV valve tears and lets in unmetered air.
- What to do
- Have the PCV valve checked; replacing it is a fairly small job.
Low oil level warning from faulty dipstick
- What you'll notice
- An 'Engine Oil Level Low' message and apparent oil loss.
- Why it happens
- A faulty dipstick lets oil vapor escape. Volvo service bulletin TJ30021 replaces the dipstick and updates engine software.
- What to do
- Check the oil and ask a dealer if TJ30021 applies to your car.
Tire pressure sensor valve stems crack
- What you'll notice
- A tire pressure warning, or a tire slowly losing air at the valve.
- Why it happens
- The aluminum valve stems on the tire pressure sensors corrode and crack.
- What to do
- Have the tire shop replace the stem or sensor; ask for a new valve kit whenever tires are changed.
Repair prices for your Volvo S80
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Repair valve body/solenoids or install a rebuilt transmission
- Clean or replace electronic throttle module
- Rebuild or replace ABS control module
- Replace PCV oil trap, hoses and intake manifold gasket
- Replace front control arms or bushings and align
- Replace front struts and mounts (pair)
- Replace engine/torque mount
- Replace ignition coil
- Replace radiator or coolant hoses
- Replace turbo oil drain tube O-rings
- Replace headlight bulb or HID ballast
- Repair A/C clutch or replace compressor
- Repair or replace and program the CEM
- Reseal vacuum pump or valve cover
- Replace PCV valve / oil separator
- Replace water pump and accessory belt
- Replace pistons and rings
- Replace oil dipstick and update engine software
- Service Haldex fluid and filter or replace pump
- Replace adaptive shocks (pair)
- Replace A/C compressor and recharge
- Replace tire pressure sensor or valve stem
- Replace V8 valve cover gaskets
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Replace driver airbagNo charge if your vehicle is included
- Replace front seat belt anchor cablesNo charge if your vehicle is included
- Update central electronic module softwareNo charge if your vehicle is included
- Update fan control module softwareNo charge if your vehicle is included
- Repair or replace clockspringNo charge if your vehicle is included
- Update engine and transmission softwareNo charge if your vehicle is included
- Update transmission control softwareNo charge if your vehicle is included
- Secure seat wiring harnessNo charge if your vehicle is included
- Reprogram tire pressure monitoring systemNo charge if your vehicle is included
- Replace starter fuseNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Pick a model year to see its safety recalls.