4WD / AWD warning light
Also called: Service 4WD, AWD light
What it means
The four-wheel or all-wheel drive system has a fault and may be working in two-wheel drive only.
An amber box with '4WD' or '4x4' inside it, or the letters 'AWD', usually low in the gauge cluster. Many trucks print words in the message area instead: 'Service 4WD', 'Service Four Wheel Drive', or '4WD system fault'. Subaru shows an AWD warning, and some SUVs use an outline of a car with the wheels and both axles picked out.
Can I keep driving?
Yes, on normal roads. Avoid snow, mud or towing until it's checked.
If it's flashing or blinking: A blinking 4WD symbol usually means the system is trying to shift and has not made it, so it is stuck part way between two-wheel and four-wheel drive. On some trucks it also blinks when the transfer case has got hot from spinning the wheels and the system has shut itself down to cool off.
What to do now
- Note if it came on after a tire change (mismatched tires can trigger it).
- Have the codes read.
Common causes
- Transfer case actuator or motor
- Mismatched tire sizes
- Wheel speed sensor
- Low fluid in the transfer case or rear differential
Checks you can do yourself
Safe, no tools in most casesDo these with the car parked and the engine off and cool. If anything looks or smells hot, wait.
Read the size off the sidewall of each tire. The numbers must be the same on all four, and on a four-wheel drive they should be worn down about the same too. Then set every tire to the pressure listed on the sticker in the driver's door opening, using a gauge at a gas station. One odd-sized or badly worn tire makes the wheels turn at different speeds, and the 4WD computer reads that as a fault.
15 minutes · Tire pressure gaugeStopped on level ground with the transmission in park, move the 4WD switch or lever through each position, pausing a few seconds at each, then put it back to normal two-wheel drive. Shut the engine off, wait a minute, and start it again. If the light came on because a shift did not finish, or because the fluid had not circulated in a system that is rarely used, this sometimes clears it. The owner's manual gives the exact procedure for your car.
5 minutes · NonePark on clean dry pavement for an hour, then stand beside the truck and look at the ground below its middle and rear. Do not crawl anywhere. Thick dark oil with a sharp smell points to a leaking transfer case or differential, and low fluid on its own is enough to set this light.
10 minutes · NoneThe owner's manual lists which fuse box holds it, usually the one inside the cabin by the driver's footwell or at the end of the dash. The lid has a map naming the 4WD or transfer case fuse. Pull that one with the plastic puller clipped inside the box and hold it up to the light: a broken metal strip inside means it has blown. Only ever fit the same amp rating.
10 minutes · Fuse puller from the fuse boxStep-by-step repair walkthroughs for the fixes below are on the way.
What not to do
- Don't use 4WD or tow with this light on. The system can grab or let go without warning.
- Don't keep driving on dry pavement if the truck feels stuck in four-wheel drive; it binds the driveline and breaks parts.
- Don't replace just one tire on a four-wheel drive to save money. A mismatched rolling size sets this light again.
- Don't rely on 4WD in snow until it has been checked, even if the light is the only sign of trouble.
What it usually turns out to be
Most likely first. Prices are typical US parts-and-labor totals for that repair, not a quote for your vehicle.
How you can tell Four-wheel drive will not engage at all, or the indicator just blinks while the truck stays in two-wheel drive. You may hear a whirring or a clunk from the middle of the vehicle when you select it. Codes in the C0327 or P0833 range are common.
The repair Replace the shift motor or actuator on the transfer case, then relearn its position with a scan tool. On some vehicles the case has to come out first, and that is most of the labor.
How you can tell A grinding or ratcheting noise from the front wheels when 4WD is selected, and the front wheels never pull. On many Fords these are small vacuum-operated units at the hubs; on GM and Toyota it is an electric actuator on the front axle.
The repair Replace the hub units or the axle actuator, and on vacuum systems the cracked hoses and the solenoid that feed them.
How you can tell The light showed up within days of a new tire, a different size, or the spare being fitted. Nothing else is wrong and four-wheel drive still works. A shop can measure the rolling size of all four tires in minutes.
The repair Match all four tires for size and tread depth, often a pair or a full set, then have the code cleared.
How you can tell The ABS and traction control lights are nearly always on with it, and the speedometer may flicker or drop to zero. A scan tool names which wheel is not reporting.
The repair Replace the sensor at that wheel, or repair its wiring where it flexes near the suspension.
How you can tell A whine, or a shudder in tight turns, with 4WD slow to engage. There is often a damp oily film around the case or a seal. Common on vehicles where four-wheel drive is almost never used.
The repair Drain and refill with the exact fluid the maker specifies, and replace the leaking seal if there is one.
How you can tell Turning the dial or pressing the button does nothing at all: no indicator, no noise from underneath. A shop separates the two by testing whether the switch signal reaches the module.
The repair Replace the selector switch, or the transfer case control module, which usually has to be programmed to the vehicle.
What a shop will do
A shop plugs in a scan tool first and reads the transfer case or 4WD module for stored codes, then measures tire sizes and tread, because a mismatch on its own sets this light. From there it commands the transfer case to shift while watching whether the motor actually moves and the position switches report back, and checks the power, ground and wiring to the actuator and the selector switch. Half an hour to an hour and a half is typical, longer if the fault comes and goes.
How to reset this light
This is a fault light, not a service reminder. A scan tool will switch it off and the dash will look normal for a few minutes, but as soon as the system tests itself or you select four-wheel drive it comes straight back, because nothing has been repaired. Clearing it only belongs at the end of the job, once the real cause is fixed, and on most vehicles the light then goes out by itself after a few drives.
A new shift motor or control module usually also needs a position relearn with a scan tool, and the procedure differs by make and model.
Trouble codes often stored with this light
Common questions
What does the 4wd / awd warning light mean?
The four-wheel or all-wheel drive system has a fault and may be working in two-wheel drive only.
Can I drive with the 4wd / awd warning light on?
Yes, on normal roads. Avoid snow, mud or towing until it's checked.
Can I keep driving with the 4WD light on?
On dry paved roads, yes. The vehicle normally falls back to two-wheel drive and drives as usual. What you have lost is four-wheel drive for the moment you need it, so get it looked at before the weather turns or before you tow anything.
Is it safe to drive in snow with this light on?
Treat the vehicle as two-wheel drive and plan for that: more following distance, gentle throttle, winter tires if you have them. The bigger worry is the system engaging or dropping out on its own in a corner, which is unsettling on a slick road.
Will the 4WD light fail an inspection?
In most US states no, because it is not an emissions light and is not on the safety list. A few states note it on a safety inspection, and it will always show up on a pre-purchase or fleet inspection.
Will it go off by itself?
Sometimes. If the cause was a shift that did not finish, or fluid that had not circulated in a system left unused for months, the light can clear after a stop and a restart. If it keeps coming back something is genuinely failing, and the codes stored in the module will say what.
Can one new tire really cause this?
Yes, and it is a common cause on four-wheel drive vehicles. A tire with more tread turns at a slightly different rate than the other three, so the computer sees front and rear speeds that do not agree and flags a fault even though every part is fine.
Sources: YourMechanic · NAPA Know How · Bruisers · CARspec