Blind spot monitor warning light
Also called: BSM light, Blind spot monitor unavailable, BLIS warning light, Service side detection system, BSD light
What it means
The blind spot monitor cannot see. Either the radar sensors behind the rear bumper are covered up, or the system has a fault, so it will not warn you about a car sitting alongside you.
Usually an amber message in the driver display rather than a symbol: Blind Spot Monitor Unavailable, BSM with a line through it, Service side detection system, or BLIS. Where there is a picture it is two cars seen from above with little waves between them, sometimes inside a mirror shape. Toyota, Honda, Ford, Nissan and Mazda all word it differently.
Can I keep driving?
Yes. Nothing about how the car drives, steers or brakes is affected. You just have no electronic help, so check your mirrors and glance over your shoulder before every lane change.
If it's flashing or blinking: The small amber light in the door mirror flashing while you signal is the system working normally, warning you about a car alongside. That is not a fault. The fault warning is a steady light or a written message in the dash.
What to do now
- Wash the back corners of the bumper and clear off any snow, ice, mud or road salt.
- Check the system has not been switched off in the vehicle settings menu.
- Drive a few miles and restart the car; messages that say temporarily unavailable usually clear themselves.
- If it keeps coming back, have it scanned, and tell the shop about any recent bumper work, hitch or trailer wiring.
Common causes
- Mud, snow, ice or road salt over the rear bumper corners
- Heavy rain or slush while driving
- The system was turned off in the vehicle settings
- A sensor knocked out of aim by a parking bump or bumper repair
- No recalibration after bumper, body or suspension work
- Corroded connector, damaged wiring, or water in the bumper harness
- A failed radar sensor or control module
Checks you can do yourself
Safe, no tools in most casesDo these with the car parked and the engine off and cool. If anything looks or smells hot, wait.
The radars sit behind the plastic at the rear corners, usually just ahead of the tail lights. With a bucket of warm soapy water and a soft cloth, wipe both corners clean of mud, slush, salt and bugs, and pick off any packed ice or snow by hand. Keep a pressure washer well back; a tight jet can push water in and shift the sensor's aim.
10 minutes · Water, soap and a clothWith the car parked, go into the dash or touchscreen settings and look for driver assistance, safety systems, or something named blind spot. If the switch is off, turn it on. Plenty of cars show a warning simply because the feature was turned off, by a previous driver, a valet or a stray tap on the screen.
5 minutes · NoneWalk around the back of the parked car and look closely at the bumper corners for cracks, scuffs, dents, or a panel sitting slightly crooked. A low-speed parking knock can crack the bracket or unplug the sensor behind plastic that still looks fine. Also note anything hanging off the back: a bike rack, a trailer or a towed load can block the sensors.
5 minutes · NoneOnce the bumper is clean and dry, drive five or ten minutes on an open road, then switch the car off and start it again. The system rechecks itself as you drive and clears a temporary message on its own. If the warning is back at the next start, or never leaves, it is a real fault and needs a scan tool.
15 minutes · NoneStep-by-step repair walkthroughs for the fixes below are on the way.
What not to do
- Don't trust the mirror blind spot alerts while this warning is showing; the system is not watching for you.
- Don't hold a pressure washer close to the rear bumper corners, as water and a hard jet can knock the sensors out.
- Don't take the car back from a body shop after rear bumper work without asking if the blind spot sensors were recalibrated.
- Don't keep clearing the message with a code reader and call it fixed; a damaged or misaimed sensor brings it straight back.
What it usually turns out to be
Most likely first. Prices are typical US parts-and-labor totals for that repair, not a quote for your vehicle.
How you can tell It appeared in bad weather or after a dirty or salty drive, the wording usually says temporarily unavailable, and it clears after a wash and a few miles. By far the most common reason, especially in winter.
The repair Clean the rear bumper corners and let the system recheck itself as you drive. Costs nothing but a bucket of water, or a car wash.
How you can tell It started right after a parking bump, a rear bumper repair or replacement, a hitch install or rear suspension work. The warning is steady rather than coming and going, and the bumper is clean.
The repair A shop refits the sensor square in its bracket and recalibrates it, which needs targets or a road procedure set by the maker. Bodywork and collision shops do this as a matter of course on later cars.
How you can tell A scan names the left or right rear sensor, one side never lights up even with a car clearly beside you, and the bumper looks undamaged. Older cars and ones that live on salted roads get this.
The repair The bumper cover comes off, that one radar sensor is replaced, and the new one is calibrated. Dealer parts cost more than aftermarket ones, and some makes will only accept their own.
How you can tell It comes and goes, works some days and not others, and the codes talk about losing communication with a sensor. Often follows a trailer wiring install, a few salty winters, or water sitting in the bumper.
The repair The shop traces the harness, cleans or replaces the corroded connector or the damaged section of wire, and seals it so water stays out.
How you can tell Both sides are dead, the message is there at every start, and the scan shows the module not responding or flagging itself. Some makes have a known software update for exactly this complaint.
The repair The module is reflashed with the current software, or replaced and then coded and calibrated to the car. If a service bulletin covers it and the car is in warranty, this can be free.
What a shop will do
They start by looking at the back of the car and reading the codes with a scan tool that talks to the body and driver-assist modules, not an engine-only reader. Then they check both rear sensors for power and for whether they are reporting, and look at the bumper for damage, a hitch, or an aftermarket accessory in the way. That is usually about an hour. If the car needs the sensors aimed again, it goes on a calibration setup with targets, which takes longer.
How to reset this light
This is not a light you are meant to reset. When the cause is simply a blocked sensor, the car clears the message itself once the bumper is clean, usually inside a mile or two of driving. When a sensor is broken, misaimed or unplugged, clearing the code with a scanner changes nothing: the warning returns at the next start or the next time you move. Fix the sensor, the wiring or the aim and the message goes away on its own.
After a sensor is replaced or a bumper repaired, most makes need a calibration procedure before the system will work again; a code clear is not a substitute.
Common questions
What does the blind spot monitor warning light mean?
The blind spot monitor cannot see. Either the radar sensors behind the rear bumper are covered up, or the system has a fault, so it will not warn you about a car sitting alongside you.
Can I drive with the blind spot monitor warning light on?
Yes. Nothing about how the car drives, steers or brakes is affected. You just have no electronic help, so check your mirrors and glance over your shoulder before every lane change.
Will my car pass inspection with the blind spot warning on?
In most places, yes. Blind spot monitoring is a convenience and safety extra, not part of an emissions test, and state safety checks look at brakes, lights, tires and steering. Rules differ by state, so if you are unsure, ask your inspection station before you go.
Is it safe to drive at night or on the highway with it on?
The car itself is fine, and nothing about braking or steering changes. The risk is habit: if you have got used to the mirror lights, you may change lanes without really looking. Set your mirrors properly and turn your head before every lane change until it is fixed.
Why did it come on in the rain and then go away?
Spray, slush and packed snow sit on the bumper and blind the radar, so the car shuts the system down and says it is unavailable for now. Once the muck is gone and you have driven a few minutes it checks itself again and the message clears. If it keeps happening in dry weather, something is actually wrong.
Did my bumper repair break the blind spot monitor?
It can. The sensors live behind the rear bumper corners, and taking the cover off, straightening the body or changing the rear ride height can move them out of aim. They often need a calibration afterwards. Go back to the shop that did the work and ask whether that step was done.
Can I just clear the code with a cheap scanner?
You can clear it, but it is not a repair. Most cheap readers only talk to the engine anyway, and the blind spot system lives in a different module. If the sensor is damaged, dirty or out of aim, the warning comes straight back.
Sources: Car ADAS · JL Wrangler Forums