High beam indicator
Also called: Blue headlight symbol
What it means
Your high beams are on.
A small blue symbol in the cluster, shaped like a headlamp lying on its side with four or five straight lines shooting out to the left. Blue means main beam almost everywhere. Cars that switch beams for you show a second version with a letter A or the word AUTO beside the lamp, often green or white, which only means the automatic mode is armed.
Can I keep driving?
Yes. Switch to low beams when there's oncoming traffic or you're following another car.
If it's flashing or blinking: The blue symbol flicking on and off as you drive usually means you are holding the stalk in the flash to pass position, or that an automatic high beam system is dipping and raising the beams for traffic ahead. A symbol that flickers while nobody touches the stalk points instead to a worn headlight switch or a poor ground.
What to do now
- Dim your lights for oncoming traffic and for cars you are following.
- If the blue symbol stays on with the stalk in the low beam position, the headlight switch is the likely fault.
- Check both main beams against a wall, because the symbol lights up even when one bulb is dead.
Common causes
- High beams switched on
- Headlight stalk or switch worn or stuck
- Burned out high beam bulb, with the symbol still lit
- Blown headlight fuse or failed relay
- Automatic high beam camera blocked or faulty
Checks you can do yourself
Safe, no tools in most casesDo these with the car parked and the engine off and cool. If anything looks or smells hot, wait.
With the car parked and the headlights on, push the lever on the left of the steering wheel toward the dash and then pull it back. The blue symbol should come on and go off cleanly as you move it. If it stays lit in both positions, the switch inside that stalk is the likely problem and your beams really are up.
2 minutes · NonePark a few feet from a garage door or a plain wall at dusk, switch the main beams on and look at the reflection. Both sides should be bright and aimed much the same. One dim or dead side with the blue light still on means a burned out bulb, because the symbol follows the switch and not the bulbs.
5 minutes · NoneThe cabin fuse box is usually behind a cover at the end of the dash or below the glovebox, and the lid carries a map of what each fuse feeds. With the car switched off, find the fuse marked high beam or headlamp, pull it and look at the little metal strip inside. A broken strip means a blown fuse. Only ever replace it with the same number.
15 minutes · Owner's manual and a fuse pullerAutomatic high beams watch the road through the same camera as lane keeping, up on the windshield behind the mirror. Clean that patch of glass inside and out and clear away snow or ice. A dirty or iced camera makes the car hold low beam, or flick between the two for no reason at all.
5 minutes · Glass cleaner and a soft clothStep-by-step repair walkthroughs for the fixes below are on the way.
What not to do
- Don't leave main beams up in traffic; you blind the oncoming driver and in most states it is a ticket.
- Don't touch a halogen bulb's glass with bare fingers, because skin oil makes it burn out early.
- Don't drop an LED bulb into a housing built for halogen to chase more light; the beam scatters into other drivers' eyes.
- Don't assume the blue symbol means both beams work, because one side can be dead with the light still on.
What it usually turns out to be
Most likely first. Prices are typical US parts-and-labor totals for that repair, not a quote for your vehicle.
How you can tell The blue symbol goes on and off cleanly as you move the stalk, both beams are bright against a wall, and nothing else on the dash is lit. Nothing is wrong at all.
The repair Move the stalk back to low beam. No parts and no repair needed.
How you can tell The symbol comes on as normal but only one side lights up bright against a wall. Many cars use a separate bulb, or a separate filament, for main beam, so low beams can look perfect while main beam is dead.
The repair The bulb is replaced, usually reached from inside the engine bay or through a cover in the wheel arch. A sealed LED headlight unit costs far more than a plain halogen bulb.
How you can tell The blue light stays on with the stalk in the low beam position, or main beam works only while you hold the stalk in the flash position. Wiggling the stalk changes what happens, which points at the switch rather than a bulb.
The repair The combination switch on the steering column is replaced, which means taking the column covers off.
How you can tell Both main beams are dead together while the low beams work fine, and you may hear no click from the fuse box when you pull the stalk. A fuse with a broken strip inside tells the same story.
The repair The fuse or the relay is replaced. If the fuse blows again, a technician looks for the short that killed it.
How you can tell On a car that dips its own beams, it stops switching to main beam at all, or an assist warning lights up at the same time. Lane keeping often misbehaves with it, because both read the road through the camera on the windshield.
The repair The windshield camera or its wiring is repaired or replaced, then the camera is aimed again with a scan tool.
How you can tell Main beam flickers, goes dim, or works only over bumps, and the plug at the back of the headlight looks green, brown or part melted when you look at it.
The repair The socket or the damaged length of wire and its ground point is repaired or replaced.
What a shop will do
A shop does the cheap checks first: switch the beams on, look at both headlights, then test the plug at the back of the dead lamp to see whether power is arriving. Power there and no light means a bulb or a corroded socket. No power means the switch, the relay, the fuse or the wiring, and they work backwards from the fuse box. On a car with automatic high beams they also scan the camera module for codes. Fifteen minutes to half an hour covers most of it.
How to reset this light
There is nothing to reset. The blue symbol is a plain indicator wired to the main beam circuit, so it is lit because the beams are up and it goes out the moment you dip them. If it stays on with the stalk down, that is a switch or wiring fault, and disconnecting the battery or clearing codes will change nothing, because the car does not store a code for this lamp in the first place.
Automatic high beams do have their own on and off setting in the car's menus, but that is a setting, not a reset.
Walk through it step by step
Common questions
What does the high beam indicator mean?
Your high beams are on.
Can I drive with the high beam indicator on?
Yes. Switch to low beams when there's oncoming traffic or you're following another car.
Why is the blue light on when I didn't turn the high beams on?
Either the stalk got nudged, or the switch inside it has worn and is stuck on main beam. Move the lever through both positions and watch the symbol. If it will not go out, your beams really are up and other drivers are being dazzled, so stay on low beam until the switch is fixed.
Is it illegal to drive with high beams on?
Every US state has a rule about dipping your beams for oncoming traffic and for cars you are following, usually within a few hundred feet. Leaving them up is a ticketable offence, and more to the point it blinds the driver coming the other way. Dip them as soon as you see headlights or tail lights.
My high beams don't work but the blue light comes on. Why?
The symbol is wired to the switch, not to the bulbs, so it lights up as soon as the car is told to use main beam whether anything shines or not. Both beams dead at once usually means a fuse or a relay. One side dead usually means a bulb or its plug.
Will this make me fail inspection?
The indicator itself is not an inspection item in most states, but your headlights are. A dead main beam or a beam aimed too high can fail a state safety inspection where one is done. Get the bulbs working and the aim checked, and the symbol takes care of itself.
Sources: YourMechanic · AAA