Home › Symptom guides › Car jerks when accelerating
Shaking

Why does my car jerk when I accelerate?

A jerk or buck when you press the gas usually comes from the engine stumbling, the transmission shifting badly, or worn parts letting the engine rock. When it happens and what the dash shows are the best clues. Answer a few questions to see the likely causes and how soon to deal with it.

Stop and get help right away if:
  • If the check engine light is flashing and the car is shaking, pull over and stop driving it.
  • If you smell fuel or see smoke, pull over, turn the engine off and get away from the car.
  • If the car suddenly loses power in traffic, turn on your hazards and get to the shoulder.
Question 1

Is the check engine light on right now?

The check engine light is the engine-shaped symbol, usually yellow or orange. A flashing light is more serious than a steady one.

Full guide: every possible outcome

Prefer to read it all? Here's every result this guide can reach.

The engine may be misfiring badly enough to cause damageStop — don't drive it

What to do now: Pull over when it's safe and turn the engine off. Have the car towed or call a mobile mechanic instead of continuing on.

Why: A flashing check engine light usually means the engine computer has detected misfires severe enough to damage the catalytic converter. Unburned fuel goes into the exhaust and can overheat it. The jerking you feel is likely cylinders cutting in and out.

Possible causes: Failed ignition coil or spark plug; Fuel injector stuck or not working; Internal engine problem, such as low compression.

A shop will usually test: Code scan and misfire counts by cylinder; Ignition coil and spark plug inspection; Fuel injector test; Compression test if needed.

An engine fault is stored. The code will narrow it downGet it checked in the next few days

What to do now: Have the trouble codes read within the next few days. Many auto parts stores do it free. Drive gently until then and avoid hard acceleration.

Why: A steady check engine light means the computer has found a fault, but not one it treats as immediately damaging. Jerking with a steady light is often an early misfire, a fuel delivery problem or a sensor giving bad readings. The stored code tells the shop where to start.

Possible causes: Early misfire from a worn spark plug or ignition coil; Faulty sensor, such as the airflow or throttle sensor; Fuel delivery problem.

A shop will usually test: Code scan and freeze-frame data; Live sensor data review; Misfire counts by cylinder.

Possibly a misfire from a worn spark plug or ignition coilGet it checked in the next few days

What to do now: Book a check within the next few days, and avoid hard acceleration until then.

Why: When a spark plug or coil is weak, a cylinder can fail to fire just when the engine is working hardest. You feel that as a jerk or buck. Moisture makes weak ignition parts worse, which is why it can be worse on damp days. A shop will usually find which cylinder is misfiring and swap parts between cylinders to test before replacing anything.

Possible causes: Worn spark plugs; Failing ignition coil or plug wire; Clogged or failing fuel injector.

A shop will usually test: Code scan and misfire counts; Spark plug and coil inspection; Coil swap test between cylinders.

The engine may not be getting enough fuel under loadGet it checked in the next few days

What to do now: Book a check within the next few days. Until then, keep the tank above a quarter full and avoid hard acceleration and long climbs.

Why: When you accelerate hard, the engine needs much more fuel. A weak fuel pump, a clogged filter or dirty injectors may keep up at idle but fall short when you ask for power, so the engine sputters and jerks. A shop will usually test fuel pressure and volume before replacing a pump.

Possible causes: Weak fuel pump; Clogged fuel filter; Dirty or failing fuel injectors; Contaminated fuel.

A shop will usually test: Fuel pressure and volume test under load; Code scan for lean-running codes; Fuel injector testing.

An air leak or a dirty airflow sensor may be throwing off the fuel mixBook a check when convenient

What to do now: Book a check when convenient. A shop can find most air leaks quickly with a smoke test.

Why: The engine computer measures the air coming in to decide how much fuel to add. A cracked vacuum hose lets in air it didn't measure, and a dirty airflow sensor misreads it. Either way the mix comes out wrong, so the car hesitates and then surges.

Possible causes: Vacuum leak from a cracked hose or intake gasket; Dirty or faulty mass airflow sensor; Dirty throttle body.

A shop will usually test: Smoke test for vacuum leaks; Code scan and live airflow data; Throttle body inspection.

The automatic transmission may be shifting harshlyGet it checked in the next few days

What to do now: Book a transmission check within the next few days. Until then, accelerate gently and avoid towing or heavy loads.

Why: A jolt right as the gears change usually means the transmission isn't controlling the shift smoothly. Low or worn-out fluid, a shift control problem or worn internal parts can all cause it. Catching it early often keeps the repair smaller, and a shop will usually check fluid, codes and software before suggesting major work.

Possible causes: Low or worn-out transmission fluid; Shift solenoid or transmission control fault; Worn internal clutches.

A shop will usually test: Transmission code scan; Fluid level and condition check; Road test with live transmission data; Check for software updates.

This may be torque converter shudderBook a check when convenient

What to do now: Book a transmission check when convenient. Tell the shop it feels like rumble strips at steady, light cruising.

Why: The torque converter connects the engine to an automatic transmission. At steady, light cruising it locks up to save fuel, and if that lockup clutch grabs unevenly, the car shudders as if crossing rumble strips. Worn fluid is a common cause, and it tends to get worse over time. A shop will usually check the fluid and any updates or service bulletins before replacing the converter.

Possible causes: Worn or contaminated transmission fluid; Worn torque converter lockup clutch; Engine misfire under light load.

A shop will usually test: Transmission code scan; Road test watching torque converter lockup data; Fluid condition check.

Possibly worn engine mounts or play in the drive axlesBook a check when convenient

What to do now: Book a check when convenient, and ask the shop to inspect the engine and transmission mounts and the drive axles.

Why: Mounts are rubber blocks that hold the engine and transmission in place. When they wear out, the engine rocks when you get on or off the gas, and you feel it as a clunk or jolt. Worn axle joints can feel very similar.

Possible causes: Worn or broken engine or transmission mount; Worn CV joint or U-joint; Loose exhaust hanger or heat shield.

A shop will usually test: Engine and transmission mount inspection; Drive axle, CV joint and U-joint check; Exhaust hanger inspection.

The clutch may be grabbing unevenly (clutch chatter)Book a check when convenient

What to do now: Book a check when convenient. Until then, let the clutch out slowly and smoothly.

Why: When the clutch grabs unevenly as you let it out, the car shudders or bucks. Oil on the clutch, worn clutch parts or weak engine mounts are the usual reasons.

Possible causes: Contaminated or worn clutch disc; Worn engine or transmission mounts; Worn or uneven flywheel.

A shop will usually test: Clutch engagement and slip test; Mount inspection; Check for an oil leak onto the clutch.

Jerking needs a code scan and a short road test to pin downBook a check when convenient

What to do now: Have the codes read and book a check. Tell the shop when the jerk happens: speed, how hard you press the gas, and whether the engine is cold or warm.

Why: Jerking can come from the engine, the transmission or worn mounts, and they can feel alike from the driver's seat. A code scan plus a short road test usually separates them quickly.

Possible causes: Ignition misfire; Fuel delivery problem; Transmission shift problem.

A shop will usually test: Code scan including pending codes; Road test; Misfire and fuel trim data.

Related guides

Sources and references: National Highway Traffic Safety Administration (NHTSA)

This guide helps you understand what may be going on and how urgent it is. It doesn't replace an in-person inspection.