Why is my transmission slipping?
A slipping transmission lets the engine rev up without the car speeding up to match, like spinning your wheels on ice. Slipping creates heat, and heat wears the transmission quickly, so catching it early matters. Answer a few questions to see the likely cause and how urgent it is.
- If the car loses drive and won't move or barely moves, get to the side of the road and have it towed.
- If you smell burning or see smoke, pull over, turn the engine off and step away from the car.
- If a transmission temperature warning comes on, pull over when it's safe and let it cool before deciding what to do.
- Avoid highways and fast traffic while the transmission is slipping. It may not respond when you need power.
Which of these best describes it right now?
Full guide: every possible outcome
Prefer to read it all? Here's every result this guide can reach.
The transmission has lost most of its ability to drive the carStop — don't drive it
What to do now: Don't try to force it by revving the engine. Put it in Park, turn it off and have the car towed.
Why: When the engine runs but the car barely moves, the transmission isn't holding. Revving it harder makes the slipping parts even hotter and can turn a repair into a full replacement.
Possible causes: Very low fluid from a leak; Badly worn internal clutches or bands; Failed pump or torque converter.
A shop will usually test: Fluid level and condition check; Line pressure test; Transmission code scan.
The transmission may be leaking fluid or overheatingStop — don't drive it
What to do now: Pull over when it's safe, turn the engine off and have the car towed.
Why: Transmission fluid cools and lubricates the transmission and gives it the pressure to hold each gear. A leak lowers that pressure and causes slipping, and a burning smell means fluid or parts are overheating. Both cause fast, expensive wear.
Possible causes: Leaking pan gasket, cooler line or seal; Overheating from slipping; Fluid dripping onto the hot exhaust.
A shop will usually test: Leak inspection; Fluid level and condition check; Transmission code scan.
The transmission may be overheating or has detected a faultStop — don't drive it
What to do now: Pull over when it's safe, put it in Park and let it cool. Then have it towed or call a mobile mechanic.
Why: Transmission fluid breaks down quickly when it gets too hot, which leads to more slipping and more heat. A warning light plus slipping means the transmission is already protecting itself or warning you that damage is possible.
Possible causes: Low fluid; Slipping clutches making heat; Blocked or damaged transmission cooler.
A shop will usually test: Transmission code scan; Fluid level and condition check; Transmission cooler inspection.
On a manual, the clutch is the first thing to checkGet it checked in the next few days
What to do now: Have the clutch checked within the next few days. Until then, drive gently and avoid hard acceleration in high gears.
Why: A clutch grips the engine to the transmission. When it wears thin, or gets oil on it, it may not hold full power, so the revs jump without more speed. It's usually most noticeable in higher gears and going uphill.
Possible causes: Worn clutch disc; Oil or fluid on the clutch; Clutch hydraulic problem.
A shop will usually test: Road test for clutch slip; Clutch hydraulic inspection; Inspection for oil leaks at the clutch.
Low transmission fluid may be causing the slip, and a leak is likelyGet it checked in the next few days
What to do now: If your car has a dipstick, top up with the exact fluid type listed in your owner's manual, following its check procedure and not overfilling. Then have the leak found within the next few days. If you're unsure of the fluid type or procedure, let a shop do it.
Why: An automatic transmission uses fluid pressure to hold each gear. When the level is low, pressure drops and the clutches inside slip. Fluid doesn't get used up like fuel, so a low level usually means a leak.
Possible causes: Leaking pan gasket or seal; Leaking cooler line; Wrong level after a recent service.
A shop will usually test: Leak inspection; Correct fluid level check to factory procedure; Transmission code scan.
Burnt-smelling fluid suggests the transmission has been running hot and may be worn insideGet it checked in the next few days
What to do now: Have the transmission inspected within the next few days. Keep trips short and gentle until then.
Why: Dark, burnt-smelling fluid has usually been overheated, often by the very slipping you're feeling. Overheated fluid protects poorly, so wear speeds up. A shop can tell from the fluid and pan whether a service may help or whether there's internal damage.
Possible causes: Worn clutches inside the transmission; Overdue fluid service; Overheating from towing or a cooler problem.
A shop will usually test: Fluid and pan debris inspection; Line pressure test; Transmission code scan.
Slipping only when cold can point to early wear or hardened internal sealsBook a check when convenient
What to do now: Let the car warm up for a minute or two before driving off, go easy until it's warm, and book a transmission check when convenient.
Why: Cold fluid is thicker, and rubber seals inside the transmission shrink and harden with age. Worn seals can leak pressure when cold, so a gear doesn't fully grip until things warm up and expand. It tends to get worse over time, so it's worth having it looked at before it does.
Possible causes: Hardened or worn internal seals; Slightly low fluid; Old or wrong-type fluid.
A shop will usually test: Fluid level and condition check; Transmission code scan; Line pressure test cold and warm.
Slipping when hot can point to worn parts or fluid that's breaking downGet it checked in the next few days
What to do now: Have the transmission checked within the next few days. Until then, avoid towing, long highway runs and heavy traffic when you can.
Why: As fluid heats up it gets thinner, and worn parts that seal fine when cold start leaking pressure. Heat also breaks the fluid down further. Slipping when hot tends to make the transmission run even hotter, so it can get worse quickly.
Possible causes: Worn internal clutches or seals; Worn or overheated fluid; Transmission cooler blocked or not working.
A shop will usually test: Transmission temperature and pressure check; Fluid condition check; Transmission cooler inspection.
Slipping on one shift is often traced to a shift solenoid or the clutch for that gearGet it checked in the next few days
What to do now: Have the transmission checked within the next few days, and note exactly which shift slips so you can tell the shop.
Why: Each gear change is controlled by an electric solenoid that sends fluid to a set of clutches. If one solenoid sticks, or one clutch pack wears, you get slipping on that shift only while the others feel normal. A shop will usually test the solenoid and read live data before deciding whether the problem is electrical or inside the transmission.
Possible causes: Sticking or failing shift solenoid; Worn clutch pack for that gear; Valve body problem.
A shop will usually test: Transmission code scan; Solenoid tests; Road test with live transmission data; Line pressure test.
The torque converter's lockup may be slippingGet it checked in the next few days
What to do now: Have it checked within the next few days. Keep highway trips short until then.
Why: At cruising speed, an automatic locks the torque converter so the engine and transmission turn together. If that lockup clutch slips, or isn't being told to lock, the revs creep up a few hundred without any gear change and fuel economy drops.
Possible causes: Worn torque converter lockup clutch; Faulty lockup solenoid; Worn or wrong fluid.
A shop will usually test: Transmission code scan; Road test watching converter slip data; Lockup solenoid test.
An electronic fault may be causing the slipping. Get the codes readGet it checked in the next few days
What to do now: Have the codes read within the next few days. Many parts stores read engine codes free, but transmission codes may need a shop scan tool.
Why: Modern automatics are computer-controlled. A bad speed sensor, solenoid or wiring problem can make the transmission shift wrong or slip, and the computer usually stores a code. Reading it first avoids guessing.
Possible causes: Faulty shift or pressure control solenoid; Faulty speed sensor or wiring; Internal wear the computer detected.
A shop will usually test: Full transmission code scan; Solenoid and sensor tests; Wiring inspection.
Have the transmission checked before the slipping gets worseGet it checked in the next few days
What to do now: Book a transmission check within the next few days, and keep trips short and gentle until then.
Why: Slipping almost never fixes itself, and each slip adds heat and wear. Catching it early gives you the best chance that a fluid service, solenoid or seal repair fixes it rather than a rebuild.
Possible causes: Low or worn fluid; Solenoid or sensor fault; Internal wear.
A shop will usually test: Transmission code scan; Fluid level and condition check; Road test.
Related guides
Sources and references: AAA · Cars Commerce · National Highway Traffic Safety Administration (NHTSA)