Why is my engine sputtering or misfiring while driving?
A misfire happens when one or more cylinders fail to burn their fuel properly, which you feel as a sputter, shake or stumble. Some misfires are a quick spark plug fix; others can damage the engine or exhaust if you keep driving. The questions below sort out which you're dealing with.
- If the check engine light is flashing, pull over when it's safe and stop driving. A severe misfire can overheat the catalytic converter.
- If you smell raw fuel or see smoke, pull over, turn the engine off and step away from the car.
- If the temperature gauge is in the red or there's steam from under the hood, pull over and turn the engine off.
- If the engine cuts out completely while you're moving, steer to a safe spot. Steering and braking will feel heavier.
Do you notice any of these along with the sputtering?
The check engine light is the orange engine-shaped light on the dash. Flashing means a misfire is happening right now and is serious.
Full guide: every possible outcome
Prefer to read it all? Here's every result this guide can reach.
A severe misfire may be happening. Stop driving to avoid damageStop — don't drive it
What to do now: Pull over when it's safe and turn the engine off. Have the car towed or call a mobile mechanic.
Why: A flashing check engine light means misfires are severe enough to send unburned fuel into the exhaust. That fuel burns inside the catalytic converter and can overheat it, destroying it and creating a fire risk. Violent shaking usually means at least one cylinder has stopped working.
Possible causes: Failed ignition coil or spark plug; Fuel injector stuck open or not firing; Mechanical damage, like a burnt valve or low compression.
A shop will usually test: Code scan and misfire counts by cylinder; Ignition coil swap test; Injector test; Compression or leak-down test.
A fuel leak or a stuck injector is possible. Don't drive itStop — don't drive it
What to do now: Pull over, turn the engine off and step away from the car. Have it towed.
Why: Sputtering together with a strong fuel smell can mean fuel is leaking onto the engine, or an injector is dumping too much fuel into a cylinder. Either way, raw fuel near hot engine and exhaust parts is a fire risk.
Possible causes: Leaking fuel line, rail or injector seal; Fuel injector stuck open; Misfire sending unburned fuel into the exhaust.
A shop will usually test: Fuel system leak inspection; Injector leak test; Code scan.
Coolant may be getting into the engine, often from a head gasket problemStop — don't drive it
What to do now: Pull over and turn the engine off. Don't open the radiator cap while it's hot. Have the car towed.
Why: A misfire with overheating or sweet-smelling white smoke points to coolant leaking into a cylinder. Coolant doesn't burn, so that cylinder misfires. Driving an overheating engine can warp or crack major parts quickly.
Possible causes: Blown head gasket; Cracked cylinder head; Overheating from a cooling system failure, causing misfires.
A shop will usually test: Cooling system pressure test; Combustion gas (block) test; Compression or leak-down test; Code scan.
One cylinder may not be firing, often from a coil or plug problemGet it checked in the next few days
What to do now: If the check engine light starts flashing or the engine shakes hard, pull over when it's safe and stop driving. Otherwise: Have it checked within the next few days. Keep trips short and gentle until then.
Why: A steady miss you can feel even at idle usually means one cylinder isn't firing at all. Common reasons are a failed ignition coil or spark plug, and a shop will usually read the code and swap the coil between cylinders to confirm before replacing parts. Driving on it for long wastes fuel and can damage the catalytic converter.
Possible causes: Failed ignition coil; Worn or fouled spark plug; Clogged or failed fuel injector; Low compression in one cylinder.
A shop will usually test: Code scan and misfire counts by cylinder; Ignition coil swap test; Spark plug inspection; Injector and compression tests if needed.
Possibly worn spark plugs or a weakening ignition coilGet it checked in the next few days
What to do now: If the check engine light starts flashing or the engine shakes hard, pull over when it's safe and stop driving. Otherwise: Have the ignition system checked within the next few days, and avoid hard acceleration until then.
Why: Under load, the engine needs a stronger spark to light the fuel. Worn plugs or a tired coil can get by at idle but miss when you accelerate, which feels like sputtering or jerking. Misfires that are left alone tend to get worse.
Possible causes: Worn spark plugs; Weak ignition coil or cracked coil boot; Worn spark plug wires (older cars).
A shop will usually test: Code scan and misfire counts; Spark plug inspection; Ignition coil test.
Damp or cold-start misfires often point to worn ignition partsBook a check when convenient
What to do now: If the check engine light starts flashing or the engine shakes hard, pull over when it's safe and stop driving. Otherwise: Book an ignition system check when convenient. Try to bring it in on a damp day or for a cold start so the shop can see it happen.
Why: Moisture lets spark escape through cracked coil boots, plug wires or dirty plugs before it reaches the cylinder. Cold engines are also harder to fire, so weak ignition parts show up first in damp or cold conditions.
Possible causes: Cracked coil boots or spark plug wires; Worn or fouled spark plugs; Water collecting around the spark plugs.
A shop will usually test: Code scan and misfire counts; Coil boot and plug wire inspection; Spark plug inspection.
The engine may not be getting enough fuelGet it checked in the next few days
What to do now: Have it checked within the next few days. Avoid long trips and highways until then.
Why: Sputtering that comes and goes, or that's worse when you need more power, can mean fuel supply is falling short. A weak pump or clogged filter may keep up at light throttle and then run short when demand rises. Left alone, it can leave you stranded. A shop will usually test fuel pressure and volume before replacing the pump.
Possible causes: Weak or failing fuel pump; Clogged fuel filter; Dirty mass airflow sensor or vacuum leak.
A shop will usually test: Fuel pressure and volume test; Code scan and fuel trim data; Smoke test for vacuum leaks.
The engine may be running short of fuel when the tank is lowSafe to check yourself first
What to do now: Keep the tank at least a quarter full and see if the sputtering stops.
Why: On turns, hills or hard braking, fuel sloshes away from the pump's pickup when the tank is low, and the engine briefly runs short. A pump that's getting weak shows this sooner. Keeping more fuel in the tank also helps the pump stay cool.
Possible causes: Fuel sloshing away from the pickup; Weakening fuel pump; Fuel gauge reading higher than the actual level.
A shop will usually test: Fuel pressure test; Fuel pump current test; Fuel gauge sender check.
You may have a tank of contaminated or wrong fuelSafe to check yourself first
What to do now: If the check engine light starts flashing or the engine shakes hard, pull over when it's safe and stop driving. Otherwise: Check your receipt for the right fuel grade, drive gently, and refill with fresh fuel from a busy station once the tank is low.
Why: Water or dirt in the fuel, or the wrong fuel type, makes the engine run rough and sputter. When the problem starts right after filling up, the fuel is a likely link.
Possible causes: Water or contamination in the fuel; Lower octane than your engine requires; Wrong fuel type.
A shop will usually test: Fuel sample check; Code scan; Fuel pressure test.
Get the codes read, then have the misfire diagnosedBook a check when convenient
What to do now: If the check engine light starts flashing or the engine shakes hard, pull over when it's safe and stop driving. Otherwise: Have the check engine codes read (many parts stores do this free), then book a check soon and describe when the sputtering happens.
Why: Misfires come from spark, fuel or compression problems. Stored codes often name the cylinder involved, which narrows it down quickly. A note of when it happens helps the shop find the cause without guessing.
Possible causes: Ignition problem (plugs, coils, wires); Fuel delivery problem; Vacuum leak or sensor problem.
A shop will usually test: Code scan and misfire counts; Ignition system check; Fuel pressure test.
Related guides
Sources and references: Edmunds · AA1Car · National Highway Traffic Safety Administration (NHTSA)