Acura RL / RLXproblems, repair costs and recalls
Problems reported across 1996–2020. Pick your model year below to see what applies to your vehicle.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems
35 documented issues across all years, most serious first.
Passenger airbag inflator can rupture (recall)
- What you'll notice
- Usually nothing you can notice. The danger only appears if the front passenger airbag goes off in a crash.
- Why it happens
- The RL's Takata passenger airbag inflator can break down after years of heat and humidity. When it fires, the metal housing can burst and throw sharp fragments into the cabin. Acura has run several recalls on these inflators.
- What to do
- Ask an Acura dealer to check your VIN for open recalls today. If a passenger inflator recall is open, book the free replacement and keep people out of the front passenger seat until it is done.
Driver airbag inflator can rupture (recall)
- What you'll notice
- No warning signs before a crash. The problem only shows up when the steering wheel airbag deploys.
- Why it happens
- Moisture can get into the driver's dual-stage Takata inflator over time, and the aged propellant can burn too fast and split the inflator housing when the airbag fires.
- What to do
- Check your VIN for open airbag recalls and have the free driver inflator replacement done as soon as the dealer can fit you in.
Older driver airbag inflator can rupture (recall)
- What you'll notice
- Nothing to notice day to day. The fault only matters if the driver airbag deploys.
- Why it happens
- The driver airbag inflators in these older RLs (including some replacement units) can absorb moisture and then rupture or underinflate the bag in a crash.
- What to do
- Look up the VIN for open recalls and get the free inflator inspection or replacement. This applies even if the car has had an airbag replaced before.
Front lower ball joints can wear and separate (recall)
- What you'll notice
- Clunking from the front end over bumps, loose or wandering steering, or uneven front tire wear. In the worst case the front wheel can fold under the car.
- Why it happens
- The front lower ball joints on early RLs could wear out faster than normal. A badly worn joint can pull apart and collapse the front suspension.
- What to do
- If you hear clunks from the front, stop driving fast and have the ball joints checked. Confirm the recall replacement was done on your VIN.
If the recall was done long ago and the joints are worn again, expect a paid repair of about 1.5-2.5 hours per side; ask for a written quote.
Transmission case bolt can loosen and lose Park (recall)
- What you'll notice
- The car may lose drive or may roll even with the shifter in Park.
- Why it happens
- A bolt inside the automatic transmission case can work loose. When it does, the parking mechanism and gear engagement can stop working properly.
- What to do
- Always set the parking brake until you confirm the recall was done. A dealer installs a redesigned bolt for free.
Brake lights may not work from a contaminated switch (recall)
- What you'll notice
- Brake lights that stay off or work only some of the time when you press the pedal.
- Why it happens
- Oil left over from manufacturing could get onto the brake light switch and stop it from making contact. Drivers behind you then get no warning when you slow down.
- What to do
- Have someone watch the brake lights while you press the pedal. If they fail, get the free recall repair, which cleans the pedal area and replaces the switch.
Corroded brake master cylinder reduces braking (recall)
- What you'll notice
- A brake pedal that sinks lower than normal or a car that takes longer to stop.
- Why it happens
- The inside of the brake master cylinder on some 2000 RLs could corrode, which lowers the pressure it sends to the brakes.
- What to do
- If the pedal feels low or soft, have the brakes checked right away. Confirm the recall master cylinder replacement was done.
Power steering hose can crack and leak (recall)
- What you'll notice
- Power steering fluid drips under the front of the car, a burning smell, whining steering, or steering that gets heavy.
- Why it happens
- Engine heat can make the power steering hose crack. Leaking fluid can land on hot engine parts and, in rare cases, catch fire.
- What to do
- If you smell burning fluid or see a leak, stop and have it checked. The recall replaces the hose with a heat-resistant one for free.
Stability control can brake on its own (recall)
- What you'll notice
- The car brakes or pulls without you pressing the pedal, possibly with the VSA warning light on.
- Why it happens
- A capacitor in the vehicle stability assist (VSA) module can be damaged and a ground connection can be loose. That can make the system apply the brakes when it should not.
- What to do
- Check that the recall was done on your VIN. The dealer installs a new wiring harness and tightens the ground at no cost.
Fuel pump relay can fail and stall the engine (recall)
- What you'll notice
- The engine stalls while driving or will not start because the fuel pump gets no power.
- Why it happens
- A coil wire inside the fuel pump relay can break, cutting power to the fuel pump.
- What to do
- If your 2005 RL stalls without warning, have the recall checked. The dealer replaces the relay for free.
Brake master cylinder seal can leak (recall)
- What you'll notice
- Low brake fluid, a brake warning light, or a brake pedal that slowly sinks.
- Why it happens
- Some service brake fluid without the right additives could dry out a seal in the master cylinder, letting fluid leak past it.
- What to do
- Watch the brake fluid level and pedal feel. Have the free recall seal replacement done and use only Honda/Acura-approved brake fluid.
Fuel pump can fail and stall the engine (recall)
- What you'll notice
- The engine may run rough, refuse to start, or stall while driving.
- Why it happens
- The impeller inside the in-tank fuel pump can swell and rub until the pump stops working. Acura has recalled these pumps.
- What to do
- Check the VIN for open fuel pump recalls. If the engine sputters or stalls, get off the road safely and have the car towed to a dealer.
Early RLX fuel pump can fail (recall)
- What you'll notice
- Hard starting, a rough-running engine, or a stall while driving.
- Why it happens
- The in-tank fuel pump in some early RLXs can fail, which cuts fuel to the engine.
- What to do
- Look up your VIN for open recalls. The dealer replaces the fuel pump module at no cost.
Timing belt teeth can separate (recall)
- What you'll notice
- The engine can suddenly stall and not restart.
- Why it happens
- Some timing belts were made with teeth that can peel off the belt. If that happens the engine loses timing and stops.
- What to do
- Confirm the recall was done. The dealer replaces the belt and checks the engine for damage free of charge.
Collision braking may brake for guardrails (recall)
- What you'll notice
- The car brakes hard on its own when passing roadside metal fences or guardrails.
- Why it happens
- The collision mitigation braking system could mistake roadside metal barriers for an obstacle ahead and apply the brakes.
- What to do
- Have the free software update done. Until then, stay alert to unexpected braking on roads lined with guardrails.
Front seat belts may not extend or retract in cold weather (recall)
- What you'll notice
- In cold weather, the driver or passenger seat belt will not pull out or wind back in.
- Why it happens
- The front seat belt retractors in some 2014 RLXs can stick in low temperatures.
- What to do
- Check for the open recall. The dealer replaces both front seat belts at no cost.
Rear lower control arm bolts can loosen (recall)
- What you'll notice
- Clunking from the rear, or the car feels loose or hard to control.
- Why it happens
- The bolts holding the rear lower control arms on some 2014 RLXs were not tightened correctly and can work loose.
- What to do
- Confirm the recall was done. The dealer replaces the bolts for free.
Harsh or delayed shift from 1st to 2nd gear
- What you'll notice
- A bump, shudder or clunk when the automatic shifts from first to second, often worse when the car is cold. Some cars hum or whine in certain gears.
- Why it happens
- Acura issued several service bulletins for 1-2 shift complaints on these RLs. Worn or dirty transmission fluid and internal wear make it worse. Leaks of transmission fluid were also covered by a bulletin.
- What to do
- Check the transmission fluid level and color. Have a shop drain and refill with genuine Honda ATF and check for codes before deciding on bigger repairs.
Engine starts then dies when the key is released
- What you'll notice
- The engine fires up while you hold the key in Start, then stalls as soon as you let go to the Run position.
- Why it happens
- Acura's bulletins point to the ignition switch, which can wear so the Run position no longer powers the engine systems after the starter is released.
- What to do
- Have the ignition switch tested. Replacing the switch usually fixes it, and it is far cheaper than chasing fuel or ignition parts.
A/C stops cooling or the compressor fails
- What you'll notice
- Warm air from the vents, weak cooling when you accelerate hard, or a noisy A/C compressor that eventually quits.
- Why it happens
- Owners report A/C compressor failures on these RLs, sometimes more than once. Acura also released bulletins on compressor control logic and poor cooling under hard acceleration.
- What to do
- Have the A/C system checked for leaks and pressures before refilling. If the compressor has failed, flushing the system and replacing the receiver-dryer helps the new one last.
SRS airbag warning light stays on
- What you'll notice
- The airbag (SRS) light stays lit on the dash, sometimes along with other warning lights.
- Why it happens
- Faulty airbag sensors are the most common problem RepairPal lists for the RL. Acura bulletins cover SRS codes from the passenger position sensor, the driver inflator circuit and the SRS control unit itself.
- What to do
- Have the SRS codes read with a proper scan tool. The airbags may not work correctly while the light is on, so do not ignore it.
Cranks but won't start with the immobilizer light flashing
- What you'll notice
- The engine turns over but will not fire, or starts and dies, and the green key (immobilizer) light blinks.
- Why it happens
- The anti-theft immobilizer is not recognizing the key, which can come from a damaged key chip, a weak key, or a fault in the immobilizer system. Acura issued bulletins for this on several model years.
- What to do
- Try your spare key first. If the spare works, the original key needs replacing. If neither works, a dealer or locksmith with the right tool can check the immobilizer.
Engine shudder or no shift into 4th gear
- What you'll notice
- A shudder while cruising, or the automatic will not upshift into fourth gear.
- Why it happens
- Acura found the engine computer software on early 2005 RLs could cause the shudder and block the upshift. Updated software was released.
- What to do
- Ask an Acura dealer to check whether the PCM software update has been done. It is a quick reflash rather than a transmission repair.
Torque converter judder while cruising
- What you'll notice
- A shudder or rumble like driving over rumble strips, usually at steady speeds with light throttle.
- Why it happens
- The lock-up clutch in the torque converter can grab unevenly. Acura released a software update and extended the warranty on the torque converter.
- What to do
- Ask a dealer about the software update and whether the extended torque converter coverage still applies to your car.
Headlight reflector can peel and dim the lights (recall)
- What you'll notice
- Headlights look dim or throw less light down the road at night.
- Why it happens
- A thin aluminum coating inside the headlight reflector can peel away, so less light is reflected forward.
- What to do
- If your headlights seem weak, check for the open recall. The dealer replaces both headlights for free.
Moaning or rubbing noise from the rear while steering
- What you'll notice
- A moan, groan or rubbing sound from the back of the car when driving straight or making small steering corrections.
- Why it happens
- Acura traced it to manufacturing errors in rear steering and suspension parts and issued a service bulletin and a warranty extension.
- What to do
- Ask an Acura dealer whether your car is covered by the warranty extension before paying for any repair.
Covered by an Acura warranty extension; out-of-coverage repairs vary widely.
Torque converter shudder at 20-60 mph
- What you'll notice
- A vibration or shudder like rumble strips when cruising at roughly 20 to 60 mph.
- Why it happens
- The torque converter lock-up clutch can judder as the transmission fluid ages. Acura's bulletins call for updated software and fresh fluid, and warn the shudder can return if the fluid breaks down again.
- What to do
- Ask a dealer about the transmission software update and a fluid change before anyone replaces the torque converter.
Rough running at cruise with a flashing check engine light
- What you'll notice
- The engine rattles or runs rough at a steady 30 to 65 mph and the check engine light blinks.
- Why it happens
- Acura linked this to the Variable Cylinder Management system, which shuts off some cylinders at cruise to save fuel.
- What to do
- A flashing check engine light means a misfire, so drive gently and get it checked soon. Ask the dealer about the related bulletin and software update.
Check engine light for misfire or lean codes
- What you'll notice
- The check engine light comes on, sometimes with a rough idle or hesitation. A scan shows misfire codes (P030X) or lean codes (P0171, P0174).
- Why it happens
- Acura opened a technical investigation into certain 2016-2020 MDX, RLX and TLX V6 models with these codes.
- What to do
- Have the codes read and ask the dealer whether your car is part of Acura's investigation or any related campaign before replacing parts.
Flashing D indicator and rough shifting
- What you'll notice
- The D or D4 indicator flashes, the check engine light comes on, the transmission shifts roughly, or more than one gear light shows at once.
- Why it happens
- A fault in the transmission range sensor (code P26C3), sometimes caused by debris, can confuse the transmission computer. RepairPal also lists rough shifting with a flashing D4 light for these years.
- What to do
- Have the codes read promptly. A dealer can check the range sensor under the related bulletin before any major transmission work.
Check engine light from an EVAP leak code
- What you'll notice
- The check engine light comes on with no change in how the car drives. A scan shows P1456 or P1457.
- Why it happens
- These codes point to a leak in the fuel vapor (EVAP) system. A binding or worn gas cap and a failed EVAP bypass solenoid are common causes, and Acura issued bulletins for both.
- What to do
- First check that the gas cap clicks tight and the seal is not cracked. If the light comes back, have the EVAP system smoke-tested.
Doors won't lock or unlock from the handle sensor
- What you'll notice
- Touching the door handle no longer unlocks or locks the car with the smart key, or the doors lock at random while driving.
- Why it happens
- The touch sensors in the outer door handles fail on these RLs. Acura also issued a bulletin saying water leaking into the door can damage the circuit so the doors stop unlocking.
- What to do
- Use the key fob buttons in the meantime. A shop can test the handle sensor and check for water inside the door before replacing parts.
Navigation clock or date shows the wrong time
- What you'll notice
- The clock reads the wrong time or 00:00, or the navigation shows the wrong date.
- Why it happens
- The GPS receiver in the navigation unit has a date counter that rolled over, so it calculates the wrong time and date. Acura issued bulletins for it.
- What to do
- This does not affect how the car drives. Ask a dealer whether a fix or update is available for your navigation unit.
Chirp from the timing belt area after warm-up
- What you'll notice
- A chirping or squeaking noise from the front of the engine once it is warm.
- Why it happens
- Acura says the timing belt can rub against the back edge of the crankshaft pulley.
- What to do
- Ask the dealer about the timing belt chirp bulletin. Have it looked at during your next service so it is not confused with a failing belt or pulley.
Tires slowly lose air
- What you'll notice
- The low tire pressure light keeps coming back and one or more tires need air every few weeks.
- Why it happens
- Acura issued bulletins on slow air leaks for these RLX and RLX Hybrid years, including corrosion of the valve stems from road salt.
- What to do
- Have the tire shop check the valve stems and wheel bead area. Ask the dealer about the related bulletins.
Repair prices for your Acura RL / RLX
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Transmission fluid drain-and-fill and diagnosis
- Replace ignition switch
- Replace A/C compressor, receiver-dryer and recharge
- Diagnose SRS codes and replace faulty sensor
- Replace gas cap or EVAP bypass solenoid
- Replace and program a new key (or diagnose immobilizer)
- Replace outer door handle with touch sensor
- Update engine computer (PCM) software
- Update transmission software and replace torque converter if needed
- Navigation software update or GPS unit service
- Transmission software update and fluid replacement
- Diagnose misfire and update engine software
- Inspect and service timing belt area per bulletin
- Diagnose misfire or lean condition
- Replace transmission range sensor
- Replace valve stems and reseal tire beads
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Replace passenger airbag inflatorNo charge if your vehicle is included
- Replace driver airbag inflatorNo charge if your vehicle is included
- Inspect and replace driver airbag inflatorNo charge if your vehicle is included
- Replace front lower ball jointsNo charge if your vehicle is included
- Install redesigned transmission case boltNo charge if your vehicle is included
- Clean pedal area and replace brake light switchNo charge if your vehicle is included
- Replace brake master cylinder, reservoir and fluidNo charge if your vehicle is included
- Install heat-resistant power steering hoseNo charge if your vehicle is included
- Install VSA wiring harness and tighten groundNo charge if your vehicle is included
- Replace fuel pump relayNo charge if your vehicle is included
- Replace master cylinder sealNo charge if your vehicle is included
- Replace fuel pump moduleNo charge if your vehicle is included
- Replace timing belt and inspect engineNo charge if your vehicle is included
- Update collision braking softwareNo charge if your vehicle is included
- Replace both headlight assembliesNo charge if your vehicle is included
- Replace front seat beltsNo charge if your vehicle is included
- Repair rear steering/suspension per bulletinNo charge if your vehicle is included
- Replace rear lower control arm boltsNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Pick a model year to see its safety recalls.