BMW X1problems, repair costs and recalls
Problems reported across 2013–2025. Pick your model year below to see what applies to your vehicle.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems
31 documented issues across all years, most serious first.
Timing chain guides wear and break
- What you'll notice
- A whine or rattle from the front of the engine, loudest on a cold start or when revving. It can progress to misfires, a check engine light, a stall or an engine that will not start.
- Why it happens
- The first N20 engines used plastic timing chain guides that turn brittle and break. Loose pieces fall into the oil pan, the chain gets slack and can jump a tooth or snap, which can wreck the engine. BMW changed the parts in early 2015.
- What to do
- Do not ignore a new whine or rattle. Have a BMW specialist inspect the chain soon, and ask about any remaining extended coverage from the class-action settlement. Replacing the chain before it fails is far cheaper than a new engine.
Coolant leaks and electric water pump failure
- What you'll notice
- Low coolant warnings, puddles or a sweet smell under the hood, the temperature gauge climbing, or a sudden overheating warning with reduced power.
- Why it happens
- Many cooling parts are plastic: the water pump housing, thermostat housing, expansion tank, hoses and radiator ends. They crack with age and heat. The electric water pump can also quit with little warning.
- What to do
- If the overheating warning comes on, pull over and shut the engine off. Have the cooling system pressure-tested to find the leak; replacing the failed part early avoids head gasket damage.
Coolant pump connector can short and start a fire (recall)
- What you'll notice
- Often no warning. Some owners see a coolant temperature or water pump warning, or smell burning plastic from the engine bay.
- Why it happens
- The electrical connector on the electric coolant pump may not seal out water. Moisture can short the connector and start a fire, even with the car parked.
- What to do
- Check your VIN for recall 24V-608 and book the free dealer repair. Until then, park outside and away from buildings if you can.
Free under recall 24V-608.
Driver airbag inflator can rupture (recalls)
- What you'll notice
- No symptoms before a crash.
- Why it happens
- The driver frontal airbag inflator, including some interim replacement inflators, can degrade with heat and humidity and burst in a crash, throwing metal fragments.
- What to do
- Ask the dealer to check your VIN for open recalls. If recall 16V-071, 19V-016 or 20V-017 is open, get the free airbag replacement right away.
Free under recalls 16V-071, 19V-016 and 20V-017.
Brake vacuum pump can fail and stiffen the pedal (recalls)
- What you'll notice
- The brake pedal suddenly feels hard and you need much more force to stop. A brake warning may appear.
- Why it happens
- The engine-driven brake vacuum pump may not get enough oil, so it wears out and stops making the vacuum that powers the brake booster.
- What to do
- Check for recalls 13V-454 and 14V-627 and have the free dealer repair done. If the pedal goes hard, press firmly and get the car checked before driving further.
Free under recalls 13V-454 and 14V-627.
Battery cable connection can overheat and stall the engine (recall)
- What you'll notice
- The engine stalls while driving and may not restart. Electrical systems can cut out.
- Why it happens
- The main positive battery cable connection at the fuse box can develop high resistance and lose power.
- What to do
- Check your VIN for recall 17V-087 and have the free connector replacement done.
Free under recall 17V-087.
Passenger airbag may be blocked by the dashboard (recall)
- What you'll notice
- No symptoms before a crash.
- Why it happens
- The instrument panel may stop the front passenger airbag from opening the way it should.
- What to do
- Check your VIN for recall 17V-062 and get the free dealer repair.
Free under recall 17V-062.
Driver seat belt may not lock (recall)
- What you'll notice
- No obvious symptom in daily driving.
- Why it happens
- The locking mechanism in the driver's seat belt retractor may not lock as designed in a crash or hard stop.
- What to do
- Check your VIN for recall 16V-747 and have the free repair done.
Free under recall 16V-747.
Seat side airbags may not deploy (recall)
- What you'll notice
- Usually no symptom; an airbag warning light may come on.
- Why it happens
- The igniters for the seat-mounted side airbags may fail to fire, so the side airbag would not inflate in a crash.
- What to do
- Check your VIN for recall 16V-914 and have the free repair done.
Free under recall 16V-914.
Crankshaft sensor software can stall the engine (recall)
- What you'll notice
- The engine can shut off while driving, and may restart only after a short wait.
- Why it happens
- The crankshaft position sensor was built with incorrect software, which can cause the engine to stall.
- What to do
- Check your VIN for recall 18V-465 and have the free sensor replacement done.
Free under recall 18V-465.
Tie rods may wear and break (recall)
- What you'll notice
- Steering feels loose or wanders, a clunk from the front, or in the worst case a loss of steering control.
- Why it happens
- Some tie rods were assembled incorrectly and can wear and break.
- What to do
- Check your VIN for recall 19V-601. Get it repaired right away, and stop driving if the steering feels loose.
Free under recall 19V-601.
Rollover sensor fault can stop airbags firing (recall)
- What you'll notice
- An airbag warning light may come on.
- Why it happens
- A fault in the rollover sensor inside the airbag control unit may keep the head airbags and seat belt pretensioners from firing in a rollover.
- What to do
- Check your VIN for recall 20V-283 and have the free control unit replacement done.
Free under recall 20V-283.
Passenger seat belt retractor may release too early (recall)
- What you'll notice
- No symptoms in daily driving.
- Why it happens
- The front passenger seat belt retractor can switch off its force limiting too soon in a crash.
- What to do
- Check your VIN for recall 21V-554 and have the free inspection and repair done.
Free under recall 21V-554.
High-pressure fuel rail can crack and leak fuel (recall)
- What you'll notice
- A fuel smell, especially near the engine, or a check engine light.
- Why it happens
- The high-pressure fuel rail may crack and leak gasoline onto the engine, which can start a fire.
- What to do
- If you smell fuel, stop driving and have it towed. Check your VIN for recall 22V-513 and get the free fuel rail replacement.
Free under recall 22V-513.
Driver front airbag may not deploy properly (recall)
- What you'll notice
- No symptoms before a crash.
- Why it happens
- Some driver airbags were built incorrectly and may not inflate as intended.
- What to do
- Check your VIN for recall 23V-079 and have the free airbag replacement done.
Free under recall 23V-079.
Integrated brake system can lose power assist (recalls)
- What you'll notice
- Brake and stability control warnings, a hard brake pedal, and longer stopping distances. ABS and stability control may stop working.
- Why it happens
- The integrated brake unit, which combines the brake booster with ABS and stability control, can malfunction. BMW has issued several campaigns, and earlier repairs may need a newer fix.
- What to do
- If brake warnings come on, drive gently to a dealer or have it towed. Check your VIN for recalls 24V-104, 24V-739 and 26V-422.
Free under recalls 24V-104, 24V-739 and 26V-422.
Brake module motor welds can break (recall)
- What you'll notice
- Brake warning lights, reduced brake assist, and ABS or stability control turning off. Rear brakes may not apply as they should.
- Why it happens
- Welds inside the servomotor of the integrated brake control module may break.
- What to do
- Check your VIN for recall 24V-697 and have the free module replacement done.
Free under recall 24V-697.
B-pillar reinforcement plates may be too weak (recall)
- What you'll notice
- No symptoms in daily driving.
- Why it happens
- Some reinforcement plates in the pillars between the doors may not be as strong as designed, which weakens side-crash protection.
- What to do
- Check your VIN for recall 24V-829 and have the free inspection done.
Free under recall 24V-829.
Front seat belt retractors may not hold (recall)
- What you'll notice
- No symptoms in daily driving.
- Why it happens
- A damaged torsion bar in the front seat belt retractors may not restrain the occupant properly in a crash.
- What to do
- Check your VIN for recall 25V-616 and have the free seat belt replacement done.
Free under recall 25V-616.
Oil leaks from the valve cover and oil filter housing
- What you'll notice
- Burning oil smell, light smoke from the engine bay, oil spots under the car, or the oil level dropping between changes.
- Why it happens
- The plastic valve cover and its rubber gasket, and the oil filter housing gasket, harden and crack from years of heat cycles. Oil then drips onto the hot exhaust. Newer engines have fewer reports, but filter housing and crankcase vent leaks still show up.
- What to do
- Have the leak traced to its source. Fix it soon, since oil on the exhaust is a fire risk and oil on belts and engine mounts damages them.
Cracked engine mounts
- What you'll notice
- Clunking or thumping from the front when shifting or pulling away, extra vibration at idle, and the engine shaking more than it should.
- Why it happens
- The engine mounts, usually the upper passenger-side mount first, crack or wear out. Some fail before 20,000 miles; most go by around 100,000.
- What to do
- Have the mounts inspected if the car shakes or clunks. A failed mount is not an emergency, but leaving it lets the engine move and strains hoses and other mounts.
Rough idle or stalling after a cold start
- What you'll notice
- The engine idles roughly or the rpm bounces after a cold start. It may sputter, shake or stall when you shift into gear.
- Why it happens
- An engine software issue on early second-generation cars. BMW released a bulletin in late 2017 with an engine computer software update.
- What to do
- Ask the dealer to check whether the latest engine software is installed. Letting the engine idle a little longer before shifting is a short-term workaround.
Front control arm clunk over bumps
- What you'll notice
- A clunk or crunching noise from the front, often the passenger side, when going over speed bumps or potholes.
- Why it happens
- The front lower control arms (wishbones) on early cars can develop play. BMW issued a 2016 bulletin to replace both with an updated part.
- What to do
- Have the front suspension checked and ask the dealer about the bulletin and updated control arms.
Transmission message asks you to use the parking brake
- What you'll notice
- A random warning when parking says to secure the car with the parking brake and see a service center. The car may not seem to go into Park properly.
- Why it happens
- A small spring in the gear selector's shift-lock solenoid does not engage reliably, so the car cannot confirm it is in Park.
- What to do
- Always set the parking brake until it is fixed. Ask a shop whether the selector spring can be repaired before paying for a whole new gear selector.
B-pillar trim may not cushion a head impact (recall)
- What you'll notice
- No symptoms in daily driving.
- Why it happens
- The upper trim on the pillar between the front and rear doors may not absorb enough energy if an occupant's head hits it in a crash.
- What to do
- Check your VIN for recall 19V-349 and have the free trim replacement done.
Free under recall 19V-349.
Rear seat belts can be pinched by trim (recall)
- What you'll notice
- A rear outer seat belt that is hard to pull out or does not retract smoothly.
- Why it happens
- An interior trim panel can pinch the second-row outer seat belts, which were trapped during assembly.
- What to do
- Check your VIN for recall 23V-260 and have the free trim adjustment done.
Free under recall 23V-260.
Hesitation when pulling away from a stop
- What you'll notice
- After you press the gas from a stop or rolling stop, the car pauses for a second or two and then surges. On a slight slope it may roll before Drive or Reverse engages. Downshifts can lag after hard acceleration.
- Why it happens
- Owners trace it to how the dual-clutch transmission and engine software manage launch. Dealer software updates have not cured it for everyone.
- What to do
- Ask the dealer to check for transmission and engine software updates and to document the complaint. Leave extra room when pulling into traffic.
Rattles and squeaks from the dashboard and trim
- What you'll notice
- Rattling, buzzing or squeaking from the dashboard, doors or rear of the car, especially on rough roads.
- Why it happens
- Loose or rubbing interior trim panels and clips. Owners report it as one of the most common complaints on this generation.
- What to do
- Note exactly where and when it happens and have the dealer or a trim shop pad or re-clip the panel.
Brake pads and rotors wear out quickly
- What you'll notice
- Brake wear warnings or squealing as soon as about 20,000 miles, and frequent pad changes front and rear.
- Why it happens
- Pad compounds chosen for strong braking, plus the stability control system applying the brakes, wear pads and rotors faster than on many other small SUVs.
- What to do
- Budget for brake service more often than usual. Rear pad changes need a scan tool to retract the electronic parking brake.
Taillight mounts can crack and loosen (recall)
- What you'll notice
- A taillight that sits loose, moves, or falls out.
- Why it happens
- The plastic brackets that hold the taillight housing can crack.
- What to do
- Check your VIN for recall 19V-074 and have the free repair done.
Free under recall 19V-074.
Infotainment screen freezes and CarPlay drops out
- What you'll notice
- The center screen freezes or lags, the radio locks up until the system reboots, and Apple CarPlay disconnects or will not reconnect.
- Why it happens
- Software glitches in the newer iDrive system.
- What to do
- Ask the dealer for the latest iDrive software update. A system reboot (holding the volume knob) usually clears a freeze.
Repair prices for your BMW X1
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace timing chain, guides, tensioner and sprockets
- Replace electric water pump and thermostat
- Replace valve cover with gasket or oil filter housing gasket
- Locate rattle and secure or pad trim panels
- Replace upper engine mount(s)
- Engine computer software update
- Replace both front lower control arms with updated parts
- Repair or replace gear selector assembly
- Front brake pads, rotors and wear sensor
- Transmission and engine software update
- iDrive software update
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Dealer recall repairNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Pick a model year to see its safety recalls.