Your 1999 Chevrolet Metroproblems, repair costs and recalls
What we've documented about the 1999 Chevrolet Metro: problems owners and shops report, typical repair and upkeep costs, and safety recalls.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems for your 1999 Chevrolet Metro
16 documented issues apply to 1999, most serious first.
Engine stalls or dies while driving
- What you'll notice
- The engine cuts out while driving or stalls when slowing down or stopping, and may be hard to restart.
- Why it happens
- Stalling while driving is the top engine complaint for these years. Owners and mechanics point to a misadjusted or failing throttle position sensor, idle problems, or fuel delivery faults.
- What to do
- Have the codes read and the throttle position sensor, idle setting and fuel pressure checked. Stalling in traffic is dangerous, so don't put it off.
Crankshaft pulley bolt loosens or breaks
- What you'll notice
- A wobble or knock from the front of the engine, belts squealing or coming off, loss of power, or the engine shutting off.
- Why it happens
- The bolt that holds the crankshaft pulley (harmonic balancer) can back out or break. A loose pulley can wear through the timing belt cover and damage the timing belt.
- What to do
- If you hear a new knock or see the pulley wobble, stop driving and have it checked. Fixing it early avoids timing belt and engine damage.
Head gasket leak on the 1.0L
- What you'll notice
- Coolant loss, overheating, white exhaust smoke, or an oil level that rises because coolant is getting into it.
- Why it happens
- A failing head gasket lets coolant leak into the oil or cylinders. Overheating makes it more likely.
- What to do
- Stop driving if it overheats or the oil looks milky. A head gasket job usually includes resurfacing the head and a new timing belt.
Misfires and stumbling from worn ignition parts
- What you'll notice
- Misfires, stuttering on acceleration, rough running, stalling or a no-start, sometimes worse in rain.
- Why it happens
- These small engines are sensitive to worn spark plugs and plug wires. Moisture in the distributor cap or wires can also cause misfires.
- What to do
- Replace plugs, wires, cap and rotor with parts made for this engine. It is a cheap first step for most running problems.
Cranks but won't start from failed distributor pickup
- What you'll notice
- The engine turns over normally but won't start, or it fires briefly and then loses spark.
- Why it happens
- The pickup or module inside the distributor can fail and stop the spark. Owners report cranking with no start at high mileage.
- What to do
- Have a shop check for spark while cranking. If spark is missing, the distributor or its pickup is a common fix.
Timing belt tensioner noise
- What you'll notice
- A whirring or chirping from the timing belt area at the front of the engine.
- Why it happens
- The timing belt tensioner pulley bearing wears. The belt and tensioner are usually replaced together.
- What to do
- Have the timing belt and tensioner inspected and replace them if worn or due. Follow the mileage interval in the owner's manual.
Front CV axles wear out
- What you'll notice
- Clicking when turning, a torn rubber boot with grease thrown around the wheel, or vibration when accelerating.
- Why it happens
- Front axle failures are among the most reported Metro problems, often around 95,000 miles. A torn boot lets dirt into the joint.
- What to do
- Have the CV boots checked at oil changes. Replacing a boot early is cheaper than an axle.
Front struts wear out
- What you'll notice
- A bouncy, floaty ride at highway speeds, nose-diving when braking, or uneven tire wear.
- Why it happens
- RepairPal lists worn front struts, around 75,000 miles, as the most common Metro problem.
- What to do
- Have the struts and mounts inspected. Replace them in pairs and get an alignment.
Manual clutch slips
- What you'll notice
- The engine revs but the car doesn't speed up, especially going uphill, or the car hesitates and jerks between shifts.
- Why it happens
- The clutch cable needs adjustment as the clutch wears. Once the adjustment is used up, the clutch disc is worn out.
- What to do
- Have the clutch pedal free play adjusted. If there is no adjustment left, the clutch needs replacing.
Water pump leaks at high mileage
- What you'll notice
- Coolant drips near the front of the engine, the coolant level drops, or the engine runs hot.
- Why it happens
- The water pump seal wears and starts to leak at high mileage. It sits behind the timing belt.
- What to do
- Watch the coolant level. Replace the water pump when the timing belt is done to save labor.
Rough idle from leaking throttle body gasket
- What you'll notice
- Uneven or high idle, or stumbling when you press the gas.
- Why it happens
- The throttle body gasket can leak air, letting unmeasured air into the engine.
- What to do
- Have a shop smoke-test for vacuum leaks. Replacing the gasket is inexpensive.
Engine clatters until warm on the 1.0L
- What you'll notice
- A rattling or clattering from the engine on cold starts that quiets down once warm.
- Why it happens
- Owners describe this as normal wear on the three-cylinder engine, most often from worn pistons and bearings.
- What to do
- Check the oil level and use the correct oil. If the noise stays when warm or gets louder, have it checked.
Drive belt squeals on cold mornings
- What you'll notice
- A squeal from the engine at startup in cold weather, worse with the lights, heater and radio on.
- Why it happens
- The alternator and water pump belt slips when it is loose or glazed.
- What to do
- Tighten the belt to spec or replace it. Don't over-tighten it, which can wear out the water pump bearing.
Check engine light from loose or worn gas cap
- What you'll notice
- The check engine light comes on with no change in how the car drives.
- Why it happens
- A gas cap that doesn't seal sets an evaporative emissions code.
- What to do
- Tighten the cap until it clicks. If the light stays on after a few drives, replace the cap and have the codes read.
Loses power with a full tank on automatics
- What you'll notice
- The car feels sluggish or idles high, mainly right after filling the tank.
- Why it happens
- A blocked vent hose between the fuel tank and the charcoal canister can keep the tank from venting properly.
- What to do
- Have the tank vent hose and charcoal canister checked for blockage.
Headlights go out while other lights work
- What you'll notice
- The headlights stop working while the taillights or other lights still work.
- Why it happens
- A loose or corroded ground wire from the light assemblies or between the battery and body is a common cause.
- What to do
- Have the ground wires and connectors cleaned and tightened before replacing switches or bulbs.
Repair prices for your 1999 Chevrolet Metro
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Stalling diagnosis
- Replace ignition control module
- Replace ignition control module or distributor pickup
- Vacuum leak diagnosis and throttle body gasket
- Replace crankshaft pulley (harmonic balancer) and bolt
- Replace timing belt and tensioner
- Replace and tension the drive belt
- Replace front CV axle (one side)
- Replace front struts (pair)
- Check engine light diagnosis
- Adjust clutch cable free play
- Replace water pump
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Checking the NHTSA recall database…