Your 2008 Chrysler Aspenproblems, repair costs and recalls
What we've documented about the 2008 Chrysler Aspen: problems owners and shops report, typical repair and upkeep costs, and safety recalls.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems for your 2008 Chrysler Aspen
11 documented issues apply to 2008, most serious first.
Electrical problems after rain from water in the fuse panel
- What you'll notice
- After heavy rain or a car wash the dash lights up with warnings, gauges jump around, the horn or door-ajar chime may go off, and the truck may not start until it dries out. Some owners find a wet driver-side floor.
- Why it happens
- Rainwater gets into the cabin near the driver's left leg and drips onto the fuse and relay panel. Clogged body and cowl drains are a common reason. Wet fuses and connectors then corrode and cause random electrical faults.
- What to do
- Look for water on the driver-side floor and around the side fuse panel. Have a shop clear the drains, find the leak and clean or replace corroded fuses and connectors before modules are damaged.
Dropped valve seat on the 4.7L V8
- What you'll notice
- A sudden misfire, flashing check engine light, rough running and loss of power, often on one cylinder.
- Why it happens
- A valve seat pressed into the aluminum cylinder head can loosen, usually after the engine has run hot. The valve then can't seal and the cylinder loses compression; a loose seat can also damage the piston.
- What to do
- Stop driving if the engine is misfiring badly. Ask for a compression or leak-down test to confirm. The fix is a cylinder head rebuild or replacement, and sometimes a replacement engine.
Engine stalls from a failing camshaft position sensor
- What you'll notice
- The engine shuts off without warning at any speed, taking power steering and brake assist with it. It may not restart for several minutes. Often no warning light comes on.
- Why it happens
- A camshaft or crankshaft position sensor that fails on and off cuts the engine computer's timing signal. Because it may not store a code, dealers often can't reproduce it.
- What to do
- Pull over safely if it stalls. Ask the shop to check the cam and crank sensors and their wiring even if no code is stored; replacing them is cheap compared with other guesses.
Steering jerks or wanders over bumps
- What you'll notice
- The steering wheel jerks in your hands over bumps or potholes, and the truck feels loose or wanders on the highway. Alignments don't hold.
- Why it happens
- Worn front suspension and steering parts such as ball joints let the front wheels move on their own over bumps.
- What to do
- Have the front end inspected for play in the ball joints, tie rods and steering parts. Replace worn parts, then get an alignment.
Takata airbag inflators can rupture (recalls)
- What you'll notice
- Usually no symptom. You may get a recall letter or see the airbag light on.
- Why it happens
- The driver and passenger front airbag inflators can break apart in a crash and spray metal pieces into the cabin because the propellant breaks down over time.
- What to do
- Check your VIN for open recalls right away and get the replacement done at a dealer for free.
Free at a Chrysler/Dodge dealer if not already done. Ask the dealer to check your VIN for open recalls.
Head gasket failure on the 4.7L
- What you'll notice
- White exhaust smoke with a sweet smell, coolant disappearing with no visible leak, milky oil, or overheating.
- Why it happens
- The head gasket fails most often after the engine overheats, letting coolant leak into the cylinders or oil.
- What to do
- Stop driving if it overheats or the oil looks milky. A shop can confirm with a cooling-system pressure or combustion-gas test.
Broken exhaust manifold bolts cause a ticking noise
- What you'll notice
- A ticking or puffing sound from the engine bay, loudest on a cold start and fading as the engine warms. You may smell exhaust under the hood.
- Why it happens
- The bolts holding the exhaust manifolds to the cylinder heads rust and snap from repeated heating and cooling, letting exhaust leak past the gasket.
- What to do
- It is not an emergency, but get it fixed before more bolts break and the leak gets worse. A shop will extract the broken bolts and fit new gaskets and hardware.
Transfer case shift motor fails or 4WD shifts on its own
- What you'll notice
- The 4WD system won't change modes, a 4WD warning light comes on, or the truck unexpectedly drops into 4-Low while driving.
- Why it happens
- The electric motor that shifts the transfer case, or its control, can fail or lose position.
- What to do
- If it shifts into 4-Low at speed, slow down and stop safely. Have the transfer case motor and its wiring tested.
Valve cover gasket oil leaks on the 4.7L
- What you'll notice
- Oil on top of the engine, a burning oil smell after driving, or light smoke from under the hood.
- Why it happens
- The rubber valve cover gaskets harden and crack with age, especially past 100,000 miles, and drip oil onto the hot exhaust.
- What to do
- Watch the oil level and get both gaskets replaced at the same time.
Coolant leaks and overheating on the 4.7L
- What you'll notice
- Coolant puddles, a low coolant warning, steam from under the hood, or the temperature gauge climbing, especially in traffic.
- Why it happens
- Water pumps, radiators, hoses and the fan clutch wear out with age. Overheating is dangerous for this engine because it can lead to head gasket and valve seat damage.
- What to do
- Stop driving if it overheats. Find and fix the leak or failed part quickly to protect the engine.
Power liftgate won't open
- What you'll notice
- Pressing the liftgate button or handle only gives two beeps and the gate stays shut.
- Why it happens
- A sticking latch or lock mechanism stops the power liftgate from releasing.
- What to do
- Try pulling and holding the outside handle while tugging the gate firmly. If it keeps happening, have the latch inspected.
Repair prices for your 2008 Chrysler Aspen
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Clear body drains, seal the leak and clean or replace the wet fuse panel/junction box
- Extract broken bolts and replace exhaust manifold gaskets and bolts
- Rebuild or replace the affected cylinder head
- Replace camshaft position sensor (and crank sensor if suspect)
- Replace worn ball joints/steering parts and align
- Replace the transfer case shift motor/encoder
- Free up or replace the liftgate latch
- Replace valve cover gaskets (both sides)
- Replace failed cooling part (water pump, hose, radiator or fan clutch)
- Replace head gasket
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Replace front airbag inflators under recallNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Checking the NHTSA recall database…