Your 2009 Chrysler Aspenproblems, repair costs and recalls
What we've documented about the 2009 Chrysler Aspen: problems owners and shops report, typical repair and upkeep costs, and safety recalls.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems for your 2009 Chrysler Aspen
11 documented issues apply to 2009, most serious first.
Dropped valve seat on the 4.7L V8
- What you'll notice
- A sudden misfire, flashing check engine light, rough running and loss of power, often on one cylinder.
- Why it happens
- A valve seat pressed into the aluminum cylinder head can loosen, usually after the engine has run hot. The valve then can't seal and the cylinder loses compression; a loose seat can also damage the piston.
- What to do
- Stop driving if the engine is misfiring badly. Ask for a compression or leak-down test to confirm. The fix is a cylinder head rebuild or replacement, and sometimes a replacement engine.
Hemi lifter or camshaft failure causing a tick or rattle
- What you'll notice
- A ticking or rattling from the top of the engine that gets louder over weeks, sometimes with a misfire or check engine light.
- Why it happens
- Hydraulic lifters on the 5.7L Hemi can wear or collapse, and a worn lifter can chew up its camshaft lobe.
- What to do
- Have the noise diagnosed early. Oil additives rarely fix it. Replacing lifters before the camshaft is damaged keeps the bill lower.
Rear axle bearing howl or failure
- What you'll notice
- A hum, howl or popping from under the rear that grows with speed. In bad cases the axle overheats, smokes or the truck leans.
- Why it happens
- Rear axle bearings wear out, sometimes after the differential ran low on oil. Some owners saw this after the pinion nut recall work.
- What to do
- Don't ignore a new rear-end noise. Check the differential oil level and have the bearings inspected before the axle is damaged.
Rear axle pinion nut can loosen (recall 13V-038)
- What you'll notice
- Often no warning. A clunk or noise from the rear axle can show up before it fails.
- Why it happens
- The nut holding the rear axle pinion gear can loosen, which can let the axle lock up and cause a loss of control.
- What to do
- Check your VIN for open recalls. A dealer will do the fix for free.
Free at a Chrysler/Dodge dealer if not already done. Ask the dealer to check your VIN for open recalls.
Takata airbag inflators can rupture (recalls)
- What you'll notice
- Usually no symptom. You may get a recall letter or see the airbag light on.
- Why it happens
- The driver and passenger front airbag inflators can break apart in a crash and spray metal pieces into the cabin because the propellant breaks down over time.
- What to do
- Check your VIN for open recalls right away and get the replacement done at a dealer for free.
Free at a Chrysler/Dodge dealer if not already done. Ask the dealer to check your VIN for open recalls.
Hybrid won't start or shuts down, and few shops can fix it
- What you'll notice
- The Aspen Hybrid shuts down while driving or won't start, and a jump-start doesn't help.
- Why it happens
- The hybrid system starts the engine using the high-voltage battery and electric motors, so faults there leave it dead. The cause varies, and few dealers are trained on this rare hybrid.
- What to do
- Call a dealer before towing to make sure it services the Aspen Hybrid. Expect to tow it to a hybrid-capable shop for diagnosis.
Head gasket failure on the 4.7L
- What you'll notice
- White exhaust smoke with a sweet smell, coolant disappearing with no visible leak, milky oil, or overheating.
- Why it happens
- The head gasket fails most often after the engine overheats, letting coolant leak into the cylinders or oil.
- What to do
- Stop driving if it overheats or the oil looks milky. A shop can confirm with a cooling-system pressure or combustion-gas test.
Broken exhaust manifold bolts cause a ticking noise
- What you'll notice
- A ticking or puffing sound from the engine bay, loudest on a cold start and fading as the engine warms. You may smell exhaust under the hood.
- Why it happens
- The bolts holding the exhaust manifolds to the cylinder heads rust and snap from repeated heating and cooling, letting exhaust leak past the gasket.
- What to do
- It is not an emergency, but get it fixed before more bolts break and the leak gets worse. A shop will extract the broken bolts and fit new gaskets and hardware.
Transfer case shift motor fails or 4WD shifts on its own
- What you'll notice
- The 4WD system won't change modes, a 4WD warning light comes on, or the truck unexpectedly drops into 4-Low while driving.
- Why it happens
- The electric motor that shifts the transfer case, or its control, can fail or lose position.
- What to do
- If it shifts into 4-Low at speed, slow down and stop safely. Have the transfer case motor and its wiring tested.
Valve cover gasket oil leaks on the 4.7L
- What you'll notice
- Oil on top of the engine, a burning oil smell after driving, or light smoke from under the hood.
- Why it happens
- The rubber valve cover gaskets harden and crack with age, especially past 100,000 miles, and drip oil onto the hot exhaust.
- What to do
- Watch the oil level and get both gaskets replaced at the same time.
Coolant leaks and overheating on the 4.7L
- What you'll notice
- Coolant puddles, a low coolant warning, steam from under the hood, or the temperature gauge climbing, especially in traffic.
- Why it happens
- Water pumps, radiators, hoses and the fan clutch wear out with age. Overheating is dangerous for this engine because it can lead to head gasket and valve seat damage.
- What to do
- Stop driving if it overheats. Find and fix the leak or failed part quickly to protect the engine.
Repair prices for your 2009 Chrysler Aspen
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Extract broken bolts and replace exhaust manifold gaskets and bolts
- Rebuild or replace the affected cylinder head
- Replace lifters (and camshaft if worn)
- Replace the transfer case shift motor/encoder
- Replace rear axle bearings or overhaul the rear axle
- Replace valve cover gaskets (both sides)
- Replace failed cooling part (water pump, hose, radiator or fan clutch)
- Replace head gasket
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Recall repair of the rear axle pinion nutNo charge if your vehicle is included
- Replace front airbag inflators under recallNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Checking the NHTSA recall database…