Home › Chrysler › Concorde
Vehicle guide

Chrysler Concordeproblems, repair costs and recalls

Problems reported across 1996–2004. Pick your model year below to see what applies to your vehicle.

Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.

Ownership snapshot

Averages, not quotes
Problems documented2211 rated serious
Safety recalls—Pick a year

Routine maintenance costs (model-wide, not specific to one year or engine)

Oil and filter changeEvery 3,000–5,000 miles · Short intervals matter on the sludge-prone 2.7L V6.
Price not verified
Ask for an estimate
Front brake pads (and rotors if worn)About every 30,000–50,000 miles
Price not verified
Ask for an estimate
Rear brake pads/rotorsAbout every 40,000–70,000 miles
Price not verified
Ask for an estimate
12V battery replacementAbout every 3–5 years
Price not verified
Ask for an estimate
Spark plugs (set of 6)Per owner's manual, often 30,000–100,000 miles depending on plug type · Inspect coil boots for cracks at the same time.
Price not verified
Ask for an estimate
Engine coolant drain and refillAbout every 5 years · 2001 and newer models use HOAT coolant.
Price not verified
Ask for an estimate

The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.

Known problems

22 documented issues across all years, most serious first.

Stop soon1998–2004Engine2.7L V6

Oil sludge leading to engine failure

What you'll notice
Ticking or knocking from the engine, an oil pressure light that flickers at idle, low idle speed, and in bad cases the engine shuts off or seizes while driving, often around 80,000 to 100,000 miles.
Why it happens
The 2.7L V6 is widely known for building up thick oil sludge that blocks oil passages and starves the bearings and timing chain. Long oil-change intervals and heat make it worse, and a leaking internal water pump can add coolant to the oil.
What to do
Change the oil and filter every 3,000 to 5,000 miles with a quality oil, and watch the oil light. If you hear knocking or the oil light flickers, stop driving and have oil pressure checked. A failed engine usually means a replacement engine.
Repair costInsufficient verified pricing for this vehicle and repair
Replace engine with used or remanufactured 2.7L. Prepare an itemized shop request.
Stop soon1998–2004Cooling2.7L V6

Internal water pump leaks coolant into the oil

What you'll notice
Coolant level keeps dropping with no puddle under the car, a sweet smell, milky or foamy oil on the dipstick, overheating, or the engine stalling or seizing.
Why it happens
On the 2.7L the water pump sits inside the engine behind the timing cover and is driven by the timing chain. When its seal fails, coolant can leak straight into the oil, ruining the bearings.
What to do
If coolant is disappearing or the oil looks milky, stop driving and have the cooling system pressure tested. Replacing the pump means removing the timing cover, so most shops replace the timing chain parts at the same time.
Repair costInsufficient verified pricing for this vehicle and repair
Replace water pump (timing cover removal), often with timing chain parts. Prepare an itemized shop request.
Stop soon1998–2004Engine2.7L V6

Timing chain stretch or breakage

What you'll notice
A rattle from the front of the engine, a check engine light, rough running, or the engine suddenly quitting and refusing to restart. A broken chain can bend the valves.
Why it happens
Sludge and poor oil flow wear the 2.7L's timing chain, guides and tensioners, and metal debris in the oil is often found with a stretched chain.
What to do
Have any new rattle checked right away. Catching a stretched chain before it breaks keeps the repair to the timing parts instead of a cylinder head or engine.
Repair costInsufficient verified pricing for this vehicle and repair
Replace timing chain, guides and tensioners. Prepare an itemized shop request.
Stop soon1998–2004Engine2.7L V6

Connecting rod bearing knock

What you'll notice
A deep knocking from the bottom of the engine that gets louder with speed, often with a flickering oil light.
Why it happens
Bearings wear out when oil flow is restricted by sludge, a common outcome on the 2.7L V6.
What to do
Stop driving as soon as you hear a deep knock; continuing can break a rod. Have oil pressure tested. A worn-out bottom end usually needs a replacement engine.
Repair costInsufficient verified pricing for this vehicle and repair
Replace engine with used or remanufactured unit. Prepare an itemized shop request.
Walk through this symptom: Engine knocking or pinging →
Stop soon1996–2004Transmission

Automatic transmission slipping, harsh shifting or failure

What you'll notice
Slipping between gears, delayed or harsh shifts, the car stuck in one gear (limp mode), refusal to shift out of first, or no drive at all.
Why it happens
The front-drive automatic used in these cars wears internally, and solenoid, servo and torque converter faults are commonly reported. Old or low fluid speeds up the wear.
What to do
Check the fluid level and condition and have codes read. Chrysler requires its own ATF+4-type fluid, so make sure the shop uses the right one. A slipping unit usually needs a rebuild or a remanufactured transmission.
Repair costInsufficient verified pricing for this vehicle and repair
Replace automatic transmission with remanufactured unit. Prepare an itemized shop request.
Walk through this symptom: Transmission slipping →
Stop soon1998–2004Engine3.2L or 3.5L V6

Timing belt failure if replacement is overdue

What you'll notice
No warning in most cases: the engine suddenly quits and won't restart. Because these engines are interference designs, the valves can be damaged.
Why it happens
The 3.2L and 3.5L V6 use a rubber timing belt with a 100,000-mile factory interval. A belt that is overdue can snap.
What to do
If your car is near or past 100,000 miles with no record of a belt change, have it replaced along with the water pump and tensioner.
Repair costInsufficient verified pricing for this vehicle and repair
Replace timing belt, tensioner and water pump. Prepare an itemized shop request.
Stop soon1996–1997Fuel3.5L V6

Fuel rail can crack and leak (recall)

What you'll notice
Fuel smell under the hood or wetness around the fuel injectors.
Why it happens
On cars with the 3.5L engine, the fuel rail O-rings can leak or the plastic rail can crack, a fire risk. Chrysler recalled them to reinforce or replace the rail.
What to do
If you smell fuel, don't drive the car. Have a dealer check that this recall was done.
Typical repair costNo charge if your vehicle is in the recall
Recall repair at a Chrysler dealer
Free under the recall if not already done. Ask the dealer to check your VIN for open recalls.
Stop soon1996–1999Transmission

Shifter interlock can let the car roll away (recall)

What you'll notice
The shifter can be moved out of Park with the key out, or the key can come out when the shifter is not in Park.
Why it happens
The ignition-park interlock in the floor shifter can fail. Chrysler recalled cars to install a new push rod in the shifter.
What to do
Always set the parking brake, and have a dealer confirm the recall was completed.
Typical repair costNo charge if your vehicle is in the recall
Recall repair at a Chrysler dealer
Free under the recall if not already done. Ask the dealer to check your VIN for open recalls.
Stop soon1998–2002Safety

Front seat back can suddenly recline (recall)

What you'll notice
The front seat back drops backward while driving.
Why it happens
The recliner bolts in the front seat can break. Chrysler recalled cars to replace the bolts.
What to do
Have a dealer check the recall status; the fix is free.
Typical repair costNo charge if your vehicle is in the recall
Recall repair at a Chrysler dealer
Free under the recall if not already done. Ask the dealer to check your VIN for open recalls.
Stop soon2000Safety

Passenger airbag has the wrong inflator charge (recall)

What you'll notice
No symptom; the passenger airbag may not protect correctly in a crash.
Why it happens
Some passenger airbag inflators were built with the wrong charge amount. The airbag module is replaced under recall.
What to do
Check your VIN for open recalls and have it done.
Typical repair costNo charge if your vehicle is in the recall
Recall repair at a Chrysler dealer
Free under the recall if not already done. Ask the dealer to check your VIN for open recalls.
Stop soon2004Body

Hood latch can fail (recall)

What you'll notice
The hood may not stay latched and could open while driving.
Why it happens
Both the main and safety hood latch could lose their function on some cars. Chrysler recalled them.
What to do
Make sure the hood is fully latched and have a dealer check the recall.
Typical repair costNo charge if your vehicle is in the recall
Recall repair at a Chrysler dealer
Free under the recall if not already done. Ask the dealer to check your VIN for open recalls.
Get checked1996–2004Steering

Steering rack and tie rod wear

What you'll notice
Clunking or creaking when turning, especially when cold, loose or wandering steering, a car that won't hold an alignment, or uneven tire wear.
Why it happens
Worn steering rack mounting bushings, inner tie rods and the rack itself are among the most reported complaints on these LH-platform cars.
What to do
Have the rack mounts and tie rods inspected for play. Worn parts make the car harder to control, so do not put this off. A rack replacement is followed by an alignment.
Repair costInsufficient verified pricing for this vehicle and repair
Replace power steering rack and pinion, then align. Prepare an itemized shop request.
Get checked1996–2004Engine

Stalling or no-start from cam or crank sensor

What you'll notice
The engine cranks but won't start, stalls while driving or at a stop, or stumbles, often with a check engine light.
Why it happens
A failing camshaft or crankshaft position sensor, or damaged wiring to it, stops the computer from knowing engine position.
What to do
Have the codes read. These sensors are inexpensive, but test the wiring and connector too so the problem doesn't come back.
Repair costInsufficient verified pricing for this vehicle and repair
Replace crankshaft or camshaft position sensor. Prepare an itemized shop request.
Walk through this symptom: Engine stalls while driving →
Get checked1998–2004Engine2.7L V6

Oil pressure light flickers at idle

What you'll notice
The oil light flickers or comes on at idle or when stopped, then goes out when you press the gas.
Why it happens
Low oil pressure at idle is often an early sign of sludge or worn bearings in the 2.7L V6, though a bad sender can also cause it.
What to do
Check the oil level now. Have a mechanic measure real oil pressure with a gauge before assuming it is just the sensor.
Repair costInsufficient verified pricing for this vehicle and repair
Test oil pressure; replace oil pressure sender and change oil. Prepare an itemized shop request.
Walk through this symptom: Oil pressure light on →
Get checked1998–2004Cooling3.2L or 3.5L V6

Coolant leak from heater tube O-ring

What you'll notice
Coolant dripping at the front of the engine, a low coolant level, or a sweet smell after driving.
Why it happens
On the 3.2L and 3.5L the front heater tube O-ring hardens with age, and the metal tube can rust through from the inside.
What to do
Top up with the correct coolant and have the leak found. Replace the tube and O-ring together.
Repair costInsufficient verified pricing for this vehicle and repair
Replace front heater tube and O-ring. Prepare an itemized shop request.
Get checked1998–2004Cooling3.2L or 3.5L V6

Overheating from worn water pump impeller

What you'll notice
The temperature gauge climbs, especially in traffic, even though no leak is visible.
Why it happens
The water pump on the 3.2L and 3.5L has a plastic impeller that can erode from rust and sediment, so it moves less coolant.
What to do
Stop if the gauge goes into the red. Have the cooling system pressure tested and the pump checked; it is usually replaced with the timing belt.
Repair costInsufficient verified pricing for this vehicle and repair
Replace water pump (usually with timing belt). Prepare an itemized shop request.
Walk through this symptom: Engine overheating →
Get checked1996–1997Engine

Head gasket failure on older V6 engines

What you'll notice
Overheating, coolant loss, white exhaust smoke, or oil and coolant mixing.
Why it happens
Owners of high-mileage 1996-1997 LH cars report blown head gaskets, often after the engine has overheated.
What to do
Stop driving if it overheats. A cooling system pressure test and combustion leak test will confirm it.
Repair costInsufficient verified pricing for this vehicle and repair
Replace head gaskets. Prepare an itemized shop request.
Get checked2000Brakes

Brake master cylinder can make brakes drag (recall)

What you'll notice
Brakes that drag, a burning smell from the wheels, or brakes that fade after heavy use.
Why it happens
On some cars without ABS, a snap ring in the master cylinder was bent during assembly and can hold the brakes partly on. The master cylinder is replaced under recall.
What to do
Have a dealer check the recall status, especially if the brakes feel like they are dragging.
Typical repair costNo charge if your vehicle is in the recall
Recall repair at a Chrysler dealer
Free under the recall if not already done. Ask the dealer to check your VIN for open recalls.
Walk through this symptom: Brakes dragging →
Get checked1999–2000Safety

Seat belt mounting bolts may not hold (recall)

What you'll notice
No symptom in normal driving.
Why it happens
Some seat belt mounting bolts may not withstand crash forces. They are replaced under recall.
What to do
Check your VIN for open recalls.
Typical repair costNo charge if your vehicle is in the recall
Recall repair at a Chrysler dealer
Free under the recall if not already done. Ask the dealer to check your VIN for open recalls.
Get checked2000–2001Safety

Child seat anchors may not hold (recall)

What you'll notice
No symptom; a child seat may not stay properly attached in a crash.
Why it happens
The child seat anchor system did not meet the federal standard, so Chrysler recalled affected cars.
What to do
If you use a child seat, have a dealer confirm this recall was done.
Typical repair costNo charge if your vehicle is in the recall
Recall repair at a Chrysler dealer
Free under the recall if not already done. Ask the dealer to check your VIN for open recalls.
Monitor1999–2001Body

Power window stops working

What you'll notice
A window will not go up or down, moves slowly, or drops into the door.
Why it happens
Power window motors and regulators are a frequently reported failure on these years.
What to do
Have the motor and regulator checked; a failed regulator is replaced as a unit. Tape or brace a dropped window until it is fixed.
Walk through this symptom: Windows, locks or radio stopped working →
Monitor2002–2004HVAC

Heater blows cold air

What you'll notice
The heater blows cold or lukewarm air, sometimes only at idle or at stoplights.
Why it happens
Low coolant, a stuck thermostat, a clogged heater core or a faulty blend door can all cause it; owners report trouble getting a lasting fix.
What to do
Check the coolant level first. If it is full, have the thermostat, heater core flow and blend door checked in that order.
Walk through this symptom: Heater blows cold air →
Price guide

Repair prices for your Chrysler Concorde

Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.

  • Replace engine with used or remanufactured 2.7L
  • Replace water pump (timing cover removal), often with timing chain parts
  • Replace timing chain, guides and tensioners
  • Replace engine with used or remanufactured unit
  • Replace automatic transmission with remanufactured unit
  • Replace power steering rack and pinion, then align
  • Replace crankshaft or camshaft position sensor
  • Test oil pressure; replace oil pressure sender and change oil
  • Replace timing belt, tensioner and water pump
  • Replace front heater tube and O-ring
  • Replace water pump (usually with timing belt)
  • Replace head gaskets

Recall repairs: usually free at the dealer

A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.

  • Recall repair at a Chrysler dealerNo charge if your vehicle is included
Get help with a shop quote →

Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.

Safety recalls
Pick a model year to see its safety recalls.
Keep a copy of this pageDownload the snapshot, every problem, the repair costs and the recalls for the Chrysler Concorde as a PDF you can save, print or bring to your shop.
This page is a general guide based on widely reported problems. Not every vehicle is affected, and it doesn't replace an in-person diagnosis.