Your 2004 Chrysler Crossfireproblems, repair costs and recalls
What we've documented about the 2004 Chrysler Crossfire: problems owners and shops report, typical repair and upkeep costs, and safety recalls.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems for your 2004 Chrysler Crossfire
8 documented issues apply to 2004, most serious first.
Engine cuts out while driving
- What you'll notice
- The engine suddenly shuts off at speed, sometimes with no warning light. Steering gets heavy. It may restart after a few minutes or not until it cools down.
- Why it happens
- Failing crankshaft or camshaft position sensors are the most common finds. Some owners also traced it to the relay control module or ignition parts, and some cases were never diagnosed.
- What to do
- Get to the side of the road safely. Have the crank and cam sensors and their wiring tested first, since they are the most common cause and fairly cheap.
Relay control module failure causes stalling or no-start
- What you'll notice
- The car won't crank or stalls, while the dash lights and radio still work. The problem comes and goes.
- Why it happens
- The relay control module, which powers the engine circuits, can fail inside; owners blame weak solder joints and relays.
- What to do
- Ask the shop to test the relay control module when the car won't start or stalls with no sensor codes.
Alternator overcharges and ruins the battery
- What you'll notice
- A rotten-egg smell, electrical problems and warning lights, and possibly the engine dying on the highway.
- Why it happens
- A failed voltage regulator in the alternator pushes too much voltage, boiling the battery and stressing other electronics.
- What to do
- If you smell sulfur, have the charging voltage checked right away. Replace the alternator and battery together.
Brake lights stop working with a brake assist warning
- What you'll notice
- The brake assist (BAS) warning light comes on when you brake, and the brake lights quit working.
- Why it happens
- The brake light switch also feeds the brake assist system, so a fault there disables both.
- What to do
- Have someone confirm your brake lights work. Get the brake light switch and its circuit checked soon, since other drivers can't see you stopping.
Key won't turn or sticks in the ignition
- What you'll notice
- The key is hard to turn, gets stuck, or won't turn at all. Sometimes the car only starts after jiggling the key or turning the steering wheel.
- Why it happens
- The ignition switch and lock housing wear, and the steering lock can bind.
- What to do
- Don't force the key. Try turning the wheel gently while turning the key. Have the ignition switch and lock assembly replaced if it keeps happening.
Anti-theft module failure stops the car from starting
- What you'll notice
- The alarm sounds at random, or the car won't start because the anti-theft system doesn't recognize the key.
- Why it happens
- The SKREEM module that controls the immobilizer, key and alarm can fail. A replacement must be programmed by a dealer.
- What to do
- Note any security light or alarm behavior and go to a dealer or a shop with Chrysler programming tools.
Rear sway bar brackets break loose
- What you'll notice
- A squeak from the rear that turns into a clunk over bumps.
- Why it happens
- The brackets that hold the rear sway bar to the body rust or crack apart.
- What to do
- Have the rear suspension mounts inspected. New brackets usually need to be welded in by a body shop.
Heated seats stop working
- What you'll notice
- One or both heated seats stay cold even though the switch light comes on.
- Why it happens
- The heating element in the seat breaks, which is the most reported Crossfire problem on RepairPal. Chrysler offers repair kits.
- What to do
- Ask a dealer or upholstery shop about the seat heater repair kit instead of a whole new seat pad.
Repair prices for your 2004 Chrysler Crossfire
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace crankshaft position sensor
- Replace ignition switch and lock housing
- Replace and program the anti-theft (SKREEM) module
- Replace alternator (and battery if damaged)
- Replace brake light switch
- Weld in new rear sway bar brackets
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Checking the NHTSA recall database…