Dodge Chargerproblems, repair costs and recalls
Problems reported across 2006–2023. Pick your model year below to see what applies to your vehicle.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems
34 documented issues across all years, most serious first.
Oil sludge and engine failure (2.7L)
- What you'll notice
- Oil pressure light, knocking, overheating, or the engine seizing, often with thick sludgy oil found at an oil change.
- Why it happens
- The 2.7L V6 is known for sludging. Its internal water pump can leak coolant into the oil, and the engine runs hot on its oil, so neglected or contaminated oil breaks down and starves the bearings.
- What to do
- Stop driving if the oil light comes on or the engine knocks. Change the oil often with the correct grade, watch for coolant loss, and have any milky oil checked right away.
Takata air bag inflators (do-not-drive recall)
- What you'll notice
- Usually no warning. In a crash, a defective inflator can rupture and throw metal fragments.
- Why it happens
- Driver and passenger front air bag inflators in these cars were recalled because they can break apart after years of heat and humidity. The affected cars are under a do-not-drive warning until repaired.
- What to do
- Check your VIN right away. If a recall is open, do not drive the car; ask the dealer for a tow or mobile repair.
Rear brake lines can wear through (recall)
- What you'll notice
- Brake fluid leaking near a rear wheel, a soft pedal, or a brake warning light.
- Why it happens
- Rear brake tubes could rub against nearby parts and wear through, causing a fluid leak and reduced braking. Chrysler recalled affected cars.
- What to do
- Check your VIN for this recall. If the pedal feels soft or fluid is leaking, do not drive the car.
ABS software can lock the rear brakes (recall)
- What you'll notice
- The rear wheels lock or skid unexpectedly during braking.
- Why it happens
- A software fault in the anti-lock brake module could lock the rear brakes. Chrysler recalled affected cars for a reflash.
- What to do
- Check your VIN for this recall and have it done before regular driving.
Drive wheels can briefly lock during shifts (recall)
- What you'll notice
- A sudden jolt or momentary skid from the rear wheels during a gear change at highway speed.
- Why it happens
- Engine computer software could briefly lock the drive wheels during certain shifts above about 40 mph. Chrysler recalled affected cars for a software update.
- What to do
- Check your VIN for this recall and have the update done right away.
Rear axle hub nuts can loosen (recall)
- What you'll notice
- Clicking or clunking from a rear wheel, vibration, or loss of drive.
- Why it happens
- The rear axle hub nuts could loosen and let a half shaft separate. Chrysler recalled affected cars.
- What to do
- Check your VIN for this recall. Stop driving and have it inspected if you hear new clunks from the rear.
Key can stick between Start and On and stall (recall)
- What you'll notice
- The engine shuts off while driving, or the key does not return fully to On after starting.
- Why it happens
- The ignition key could stay partway between Start and On, which can shut the engine off and disable air bags. Chrysler recalled affected cars.
- What to do
- Check your VIN for this recall. Make sure the key returns fully to On after starting until the repair is done.
Front spindle nut may be missing (recall)
- What you'll notice
- A clunk or wobble from a front wheel. In the worst case the wheel can come loose.
- Why it happens
- Some cars left the factory without a front wheel spindle nut installed. Chrysler recalled them for inspection.
- What to do
- Check your VIN for this recall. Stop driving if a front wheel feels loose or noisy.
Key can be removed when not in Park (recall)
- What you'll notice
- The key fob comes out of the ignition even though the shifter is not in Park, and the car can roll.
- Why it happens
- The wireless ignition node could bind and release the key before the car is in Park. Chrysler recalled affected cars.
- What to do
- Check your VIN for this recall. Always confirm Park and set the parking brake before leaving the car.
HEMI lifter tick and camshaft wear
- What you'll notice
- A ticking or tapping from the engine, often louder at idle or on a cold start, sometimes with a misfire and check engine light.
- Why it happens
- The roller lifters, especially those used by the cylinder-deactivation system, can stop rolling properly. That wears the lifter and the camshaft lobe it rides on.
- What to do
- Do not ignore a new tick. Have the engine inspected soon, because a failed lifter destroys the camshaft and spreads metal through the engine. Use the correct oil grade and keep up with changes.
Sudden alternator failure (recalls)
- What you'll notice
- The battery light comes on, lights may dim, and the car can stall or refuse to restart. Some owners notice a hot or burning smell near the engine.
- Why it happens
- The alternator on these cars can fail without much warning. Chrysler recalled many of them, partly because a failing unit could short internally and create a fire risk.
- What to do
- Have the charging system tested right away and check your VIN for open recalls. Avoid driving with the battery light on, because the car can shut down once the battery runs flat.
Left cylinder head valve seat wear (3.6L)
- What you'll notice
- Check engine light with a misfire, usually on cylinder 2, plus a rough idle, ticking, and a loss of power.
- Why it happens
- Early 3.6L engines could wear a valve seat in the left cylinder head, letting compression leak from that cylinder. Chrysler revised the head and extended warranty coverage on it.
- What to do
- Have the misfire diagnosed with a compression or leak-down test. Ask a dealer whether any extended coverage still applies to your VIN.
Overheated power center can disable ABS and stability control (recall)
- What you'll notice
- ABS and stability control warning lights come on, and those systems stop working.
- Why it happens
- A connection in the power distribution center could overheat and cut power to the anti-lock brake and stability systems. Chrysler recalled affected cars.
- What to do
- Check your VIN for this recall. Brake gently and allow extra distance until it is repaired.
Headlamp wiring can overheat (recall)
- What you'll notice
- The low beam headlights flicker or go out.
- Why it happens
- A headlamp sub-harness could overheat at its connection and cut power to the low beams. Chrysler recalled affected cars.
- What to do
- Check your VIN for this recall. Avoid night driving if the low beams are failing.
Side air bags can deploy unexpectedly (recall)
- What you'll notice
- Side air bags go off without a crash, for example after a door slam or a bump.
- Why it happens
- The side impact sensors were too sensitive. Chrysler recalled affected cars for a software update.
- What to do
- Check your VIN for this recall and have it done promptly.
Connecting rod bearing failure (recall)
- What you'll notice
- A knocking sound from the engine, low oil pressure warning, or the engine quitting.
- Why it happens
- Debris left in some engines could damage a connecting rod bearing. Chrysler recalled affected cars built from late summer 2011.
- What to do
- Check your VIN for this recall. Stop driving if the engine starts knocking or the oil light comes on.
Shifter confusion and roll-away risk (recall)
- What you'll notice
- The car is not actually in Park when the driver thinks it is, and it can roll after the driver gets out.
- Why it happens
- The electronic shift lever springs back to center after each selection, which made it easy to misjudge the gear. Chrysler recalled these cars and added software that shifts to Park if the driver door opens while in gear.
- What to do
- Check your VIN for the recall and have it completed. Until then, always confirm the dash shows P and set the parking brake.
AWD transmission output shaft can break (recall)
- What you'll notice
- A bang or clunk, then loss of drive power. The car may roll if parked without the parking brake.
- Why it happens
- The transmission output shaft on some all-wheel-drive cars could fracture. Chrysler recalled them.
- What to do
- Check your VIN for this recall. Always set the parking brake when parked until it is done.
Loose front driveshaft bolts on AWD (recall)
- What you'll notice
- A clunk or vibration from under the car, and in the worst case a loss of drive power.
- Why it happens
- Bolts holding the front driveshaft on some all-wheel-drive V6 cars could loosen, letting the shaft disconnect. Chrysler recalled them.
- What to do
- Check your VIN for open recalls. If you hear a new clunk or feel vibration, have the driveline inspected before driving further.
Cruise control may not turn off (recall)
- What you'll notice
- Cruise control keeps holding speed after you try to cancel it.
- Why it happens
- A software fault could stop cruise control from disengaging in certain conditions. Chrysler recalled affected cars for an update.
- What to do
- Check your VIN for this recall and avoid using cruise control until it is done. Firm braking still overrides it.
Fuel rail hose can leak (recall)
- What you'll notice
- A strong gasoline smell from the engine bay or visible fuel wetness.
- Why it happens
- Damage to an O-ring and the fuel rail crossover hose could let fuel leak near hot engine parts. Chrysler recalled affected SRT cars.
- What to do
- Do not drive the car if you smell fuel. Check your VIN for this recall and have it towed if needed.
Oil cooler hoses can burst (recall)
- What you'll notice
- Sudden oil loss, oil spray or smoke from under the car, and an oil pressure warning.
- Why it happens
- The engine oil cooler hoses could fail and dump oil quickly, which can coat the tires or catch fire. Chrysler recalled affected Hellcats.
- What to do
- Check your VIN for this recall. If oil sprays or the oil light comes on, pull over and shut the engine off.
Engine computer voltage regulator can fail and stall (recall)
- What you'll notice
- The engine shuts off while driving and may not restart.
- Why it happens
- A voltage regulator inside the engine control module could fail. Chrysler recalled affected cars.
- What to do
- Check your VIN for this recall and get it done before regular driving.
Wrong park lock rod (recall)
- What you'll notice
- The car may not stay in Park and can roll.
- Why it happens
- An incorrect park lock rod could stop the transmission from fully engaging Park. Chrysler recalled affected cars.
- What to do
- Check your VIN for this recall. Always set the parking brake until it is repaired.
Side curtain air bag inflators can rupture (recall)
- What you'll notice
- Usually no warning beforehand.
- Why it happens
- A manufacturing defect could make the side curtain air bag inflators break apart in a crash and send metal pieces toward occupants. Chrysler recalled affected cars.
- What to do
- Check your VIN for this recall and have it repaired as soon as parts are available.
Shifter can slip out of Drive (recall)
- What you'll notice
- The car unexpectedly shifts out of Drive and loses power while moving.
- Why it happens
- A problem in the shifter assembly could let the transmission leave Drive. Chrysler recalled affected cars.
- What to do
- Check your VIN for this recall and get it done before regular driving.
Parking brake may not hold (recall)
- What you'll notice
- The car creeps or rolls with the parking brake set.
- Why it happens
- The parking brake on some cars was not adjusted correctly at the factory. Chrysler recalled affected cars.
- What to do
- Check your VIN for this recall. Always confirm Park and park on level ground until it is fixed.
Stalls right after refueling
- What you'll notice
- The engine stalls or runs rough a short time after filling the tank, usually when stopping or idling. It typically restarts.
- Why it happens
- A float valve inside the fuel tank can swell from ethanol fuel and stick open, letting liquid fuel flood the vapor recovery system. Chrysler responded with extended coverage on the fuel tank.
- What to do
- Stop filling at the first pump click and do not top off. Have a dealer check the tank valve and ask about the extended tank coverage for your VIN.
Early front suspension and tie rod wear
- What you'll notice
- Clunks over bumps, loose or wandering steering, uneven tire wear, or a steering wheel that is off center.
- Why it happens
- These heavy sedans are known for wearing out front tie rods, sway bar links and lower ball joints earlier than expected.
- What to do
- Have the front end inspected and aligned. Replace worn ball joints and tie rods promptly, since a failed joint can affect steering control.
Oil filter housing leak (3.6L)
- What you'll notice
- Oil drips under the back of the engine, a burning-oil smell after driving, or the oil level dropping between changes. Some cases also lose coolant.
- Why it happens
- The oil filter and cooler housing is plastic and sits in the valley under the intake. Heat cycling can crack it or harden its seals.
- What to do
- Have a shop find the exact source of the leak. Keep the oil topped up until it is fixed, and use an updated replacement housing.
Instrument cluster may not show warnings (recall)
- What you'll notice
- Warning lights do not come on at startup or when there is a fault.
- Why it happens
- The instrument cluster in some cars could fail to light its warning lamps. Chrysler recalled affected cars.
- What to do
- Check your VIN for this recall and have it done soon so you do not miss a real warning.
Windshield may not be bonded properly (recall)
- What you'll notice
- Usually nothing noticeable. Some cars may show gaps, wind noise or leaks around the glass.
- Why it happens
- The windshield on some cars was not bonded correctly and could come out in a crash. Chrysler recalled affected cars.
- What to do
- Check your VIN for this recall and have the windshield inspected and rebonded soon.
Broken exhaust manifold bolts (HEMI)
- What you'll notice
- A ticking or puffing sound from the engine bay that is loudest on a cold start and fades as the engine warms up.
- Why it happens
- The manifold bolts go through many heat cycles and can snap, letting exhaust leak at the manifold. It is often mistaken for lifter tick.
- What to do
- Have the manifold area checked so a lifter problem is ruled out. The leak itself is not urgent, but it tends to get worse.
Paint bubbling on aluminum body panels
- What you'll notice
- Bubbles, blisters or flaking paint on the hood, fenders or doors, often along edges.
- Why it happens
- Corrosion can form under the paint on aluminum panels. Chrysler published a service bulletin on inspecting and refinishing these panels.
- What to do
- Show it to a dealer early, especially if the car is under warranty, before the corrosion spreads.
Repair prices for your Dodge Charger
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace engine with a used 2.7L V6
- Replace fuel tank vent/control valve assembly
- Replace front tension struts and tie rod ends, then align
- Replace air bag inflator/module
- Replace rear brake lines and bleed brakes
- Reprogram ABS control module
- Reprogram transmission control software
- Replace and torque rear axle hub nuts
- Replace ignition switch (key module)
- Install and torque front spindle nut
- Repair shifter and ignition park interlock
- Replace camshaft and lifters
- Extract broken bolts and replace manifold gasket
- Replace alternator
- Replace left cylinder head
- Replace oil filter housing and oil cooler assembly
- Replace ABS fuse/relay and inspect power center
- Repair headlamp wiring connectors
- Update or replace side air bag control unit
- Replace engine with a used or remanufactured 3.6L
- Software update that adds Auto Park
- Replace transfer case output shaft parts
- Replace and torque front driveshaft bolts
- Reprogram engine computer software
- Replace fuel rail supply hose
- Replace engine oil cooler hoses
- Replace and program engine computer (PCM)
- Replace transmission park lock rod
- Replace side curtain air bags
- Reprogram instrument cluster software
- Remove and rebond windshield
- Repair or replace gear shifter assembly
- Repair rear parking brake system
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Pick a model year to see its safety recalls.